Trailer Hitch Classes and Ball Sizes: Receiver Openings, GTW and Tongue Weight

Receiver hitches are grouped in classes by opening and rating: Class I–II, 1-1/4 in receiver (up to 2,000 / 3,500 lb); Class III–IV, 2 in (up to 8,000 / 10,000 lb); Class V, 2-1/2 in (up to about 20,000 lb). Tongue weight is rated at about 10 % of the trailer weight. The ball must match the coupler: 1-7/8, 2 or 2-5/16 in, or 50 mm in Europe.

9 sizesChecked 2026-11-155 sources
Receiver openings1-1/4 in · I–II2 in · III–IV2-1/2 in · VHitch balls1-7/8 in50 mm2 in2-5/16 in
Receiver openings (squares) and ball diameters (circles), one scale.Drawn to scale

Size chartTap a size for its drawing and full specs

9 of 9
Class / ball□Receiver openingmmin⌀Ball diametermminMax. gross trailer weight (GTW)kglbMax. tongue weight (TW)kglbHitch pin diametermminShank
Receiver hitch classes
Class I hitch31.81 1/4—9072,0009120012.71/2—
Class II hitch31.81 1/4—1,5883,50015935012.71/2—
Class III hitch50.82—2,268–3,6295,000–8,000227–363500–80015.95/8—
Class IV hitch50.82—4,53610,000454100015.95/8—
Class V hitch63.52 1/2—5,443–9,07212,000–20,000544–12251200–270015.95/8—
Hitch balls
1-7/8 in hitch ball—47.61 7/89072,000——3/4 in
2 in hitch ball—50.821,588–4,5363,500–10,000——3/4, 1, 1-1/4 or 1-3/8 in
2-5/16 in hitch ball—58.72 5/162,722–13,6086,000–30,000——1 or 1-1/4 in
50 mm tow ball (ISO)—50.01.969set by towbar D-value and vehicle——flange or swan-neck (detachable)

Which rating counts

GTW (gross trailer weight) is the loaded trailer's total weight. TW (tongue weight) is the downward load on the ball, normally 10–15 % of GTW for a bumper-pull trailer; less than about 10 % makes a trailer sway. A 6,000 lb camper should put 600–900 lb on the ball.

The towing system is only as strong as its weakest part: hitch (label on the receiver), ball mount, ball (stamped on top), coupler (stamped on the trailer tongue), safety chains and the vehicle's own tow rating from the owner's manual. A Class IV hitch on a vehicle rated for 5,000 lb is a 5,000 lb system.

Weight-distribution hitches spread tongue weight to the front axle and the trailer axles; many Class III–IV hitches carry two ratings, a lower one for weight-carrying and a higher one with weight distribution.

About Hitch Classes & Balls

The receiver class tells you which ball mounts and accessories fit: 1-1/4 in shanks (Class I–II) and 2 in shanks (Class III–IV) are the common sizes for bike racks and cargo carriers. Adapters allow a 1-1/4 in accessory in a 2 in receiver, but never the reverse, and adapters reduce the rating and add leverage.

Ball size must match the trailer's coupler exactly: a 2 in ball in a 2-5/16 in coupler can pop out on a bump. The coupler is stamped with its ball size and rating; the ball carries its rating on top. Shank diameter (3/4, 1 or 1-1/4 in) must match the hole in the ball mount.

In Europe, cars tow with a 50 mm ball (ISO 1103) on a type-approved towbar rated by its D-value; the caravan or trailer coupling is also 50 mm. Static nose weight is typically limited to 50–100 kg by the car, much less than US tongue weights for similar trailers.

Questions

What size is a Class 3 hitch receiver?

2 in square. Class III hitches are typically rated 5,000–8,000 lb gross trailer weight and 500–800 lb tongue weight.

What are the hitch classes?

Class I: 1-1/4 in, 2,000 lb. Class II: 1-1/4 in, 3,500 lb. Class III: 2 in, up to 8,000 lb. Class IV: 2 in, up to 10,000 lb. Class V: 2 or 2-1/2 in, about 12,000–20,000 lb.

What size hitch ball do I need?

The size stamped on the trailer's coupler: 1-7/8 in for light trailers up to about 2,000 lb, 2 in for most boat and camper trailers, 2-5/16 in for heavy trailers.

How much tongue weight should a trailer have?

About 10–15 % of the loaded trailer weight. A 5,000 lb trailer: 500–750 lb.

Is a 50 mm ball the same as a 2 inch ball?

No. 50 mm is about 1.97 in. Use a 50 mm coupling on a 50 mm ball and a 2 in coupler on a 2 in ball.

Sources

  1. SAE J684: Trailer couplings, hitches and safety chains, automotive type
  2. CURT: Trailer hitch classes explained
  3. Horizon Global (Draw-Tite, Reese): Hitch class and ball rating guide
  4. etrailer: Trailer hitch classes and ball size guide
  5. ISO 1103: Road vehicles, coupling balls for caravans and light trailers, dimensions

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.