Flanged Ball Bearing Size Chart: F6xx and MF Series
A flanged bearing has a collar on the outer ring, so it locates itself axially in a plain through-bore with no shoulder or circlip. The size is that of the base bearing: F625ZZ is a 625 (5 × 16 × 5 mm) with an 18 mm flange; MF105ZZ is an MR105 (5 × 10 × 4 mm) with an 11.6 mm flange.
Size chartTap a size for its drawing and full specs
| Bearing | dBore diametermmin | DOutside diametermmin | BWidth (shielded ZZ)mmin | B₀Width, openmmin | D₁Flange diametermmin | C₁Flange widthmmin |
|---|---|---|---|---|---|---|
| F series: flanged 62x / 60x / 68x | ||||||
| F623 | 30.118 | 100.394 | 40.157 | — | 11.50.453 | 10.039 |
| F624 | 40.157 | 130.512 | 50.197 | — | 150.591 | 10.039 |
| F625 | 50.197 | 160.630 | 50.197 | — | 180.709 | 10.039 |
| F626 | 60.236 | 190.748 | 60.236 | — | 220.866 | 1.50.059 |
| F608 | 80.315 | 220.866 | 70.276 | — | 250.984 | 1.50.059 |
| F688 | 80.315 | 160.630 | 50.197 | 40.157 | 180.709 | 1.10.043 |
| MF series: flanged miniature (MR) | ||||||
| MF63 | 30.118 | 60.236 | 2.50.098 | 20.079 | 7.20.283 | 0.60.024 |
| MF74 | 40.157 | 70.276 | 2.50.098 | 20.079 | 8.20.323 | 0.60.024 |
| MF85 | 50.197 | 80.315 | 2.50.098 | 20.079 | 9.20.362 | 0.60.024 |
| MF105 | 50.197 | 100.394 | 40.157 | — | 11.60.457 | 0.80.031 |
| MF106 | 60.236 | 100.394 | 30.118 | — | 11.20.441 | 0.60.024 |
| MF115 | 50.197 | 110.433 | 40.157 | — | 12.60.496 | 0.80.031 |
| MF117 | 70.276 | 110.433 | 30.118 | — | 12.20.480 | 0.60.024 |
| MF128 | 80.315 | 120.472 | 3.50.138 | — | 13.60.535 | 0.80.031 |
No exact match. The nearest sizes:
How to read flanged bearing numbers
F in front of a ball bearing number means a flanged outer ring: F625 = flanged 625, F608 = flanged 608, F688 = flanged 688. MF is the flanged version of the MR miniature series, named by bore and OD: MF105 = 5 mm bore, 10 mm OD; MF128 = 8 × 12 mm.
ZZ / 2Z = metal shields, 2RS = rubber seals. Several MF and F68 sizes are wider shielded than open (MF105 is 3 mm open and 4 mm as MF105ZZ), and flange dimensions can differ between the open and shielded versions too. The chart lists the shielded bearing, which is what most suppliers stock.
About Flanged Bearings
The flange takes over the job of a housing shoulder: drill a straight hole to the bearing OD, push the bearing in until the flange seats, done. That is why flanged bearings are everywhere in 3D printers (F623 and F625 belt idlers, often stacked in pairs), small conveyors, model engineering and printers.
The flange can carry only light axial load toward the housing. Do not rely on it as a thrust face, and support it fully: a flange overhanging a chamfered hole edge can crack.
ISO 8443 standardises flange diameter and width for metric flanged bearings, and the F6xx sizes here agree between SKF, NSK and Koyo. MF miniature flanges vary slightly by maker (MF105: 11.6 mm in most tables), so check the drawing if the flange sits in a counterbore.
Questions
What size is an F625ZZ bearing?
5 mm bore, 16 mm outside diameter, 5 mm wide, with an 18 mm diameter, 1 mm thick flange.
What size is an MF105ZZ?
5 mm bore, 10 mm outside diameter, 4 mm wide, flange 11.6 mm diameter × 0.8 mm. The open MF105 is 3 mm wide.
Is F623 the same as 623 with a flange?
Yes: same 3 × 10 × 4 mm bearing, plus an 11.5 mm × 1 mm flange on the outer ring.
What hole do I need for a flanged bearing?
A straight bore equal to the bearing OD (for example 16 mm for F625), usually toleranced J7 or K7, with a square, burr-free face for the flange to seat on.
Sources
- ISO 8443:1999, Rolling bearings, radial ball bearings with flanged outer ring, flange dimensions
- NSK: Miniature ball bearings, metric series with flange (MF…, F6…)
- SKF: Deep groove ball bearings with flanged outer ring (F6.., F69..)
- Misumi: Small diameter flanged ball bearings, standard table
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.