Linear Bearing Size Chart: LM UU, LM LUU, LME
A linear ball bushing runs on a hardened round shaft. The number is the shaft diameter: LM8UU fits an 8 mm shaft, is 15 mm outside and 24 mm long. The LM series (Asian / JIS dimensions) and the LME series (European ISO dimensions) fit the same shaft but not the same housing bore.
Size chartTap a size for its drawing and full specs
| Bushing | drShaft diametermmin | DOutside diametermmin | LLengthmmin | BGroove spacing (outer faces)mmin | WGroove widthmmin | D1Groove diametermmin |
|---|---|---|---|---|---|---|
| LM…UU standard (Asian / JIS) | ||||||
| LM3UU | 30.118 | 70.276 | 100.394 | — | — | — |
| LM4UU | 40.157 | 80.315 | 120.472 | — | — | — |
| LM5UU | 50.197 | 100.394 | 150.591 | — | — | — |
| LM6UU | 60.236 | 120.472 | 190.748 | 13.50.531 | 1.10.043 | 11.50.453 |
| LM8UU | 80.315 | 150.591 | 240.945 | 17.50.689 | 1.10.043 | 14.30.563 |
| LM10UU | 100.394 | 190.748 | 291.142 | 220.866 | 1.30.051 | 180.709 |
| LM12UU | 120.472 | 210.827 | 301.181 | 230.906 | 1.30.051 | 200.787 |
| LM13UU | 130.512 | 230.906 | 321.260 | 230.906 | 1.30.051 | 220.866 |
| LM16UU | 160.630 | 281.102 | 371.457 | 26.51.043 | 1.60.063 | 271.063 |
| LM20UU | 200.787 | 321.260 | 421.654 | 30.51.201 | 1.60.063 | 30.51.201 |
| LM25UU | 250.984 | 401.575 | 592.323 | 411.614 | 1.850.073 | 381.496 |
| LM30UU | 301.181 | 451.772 | 642.520 | 44.51.752 | 1.850.073 | 431.693 |
| LM35UU | 351.378 | 522.047 | 702.756 | 49.51.949 | 2.10.083 | 491.929 |
| LM40UU | 401.575 | 602.362 | 803.150 | 60.52.382 | 2.10.083 | 572.244 |
| LM50UU | 501.969 | 803.150 | 1003.937 | 742.913 | 2.60.102 | 76.53.012 |
| LM60UU | 602.362 | 903.543 | 1104.331 | 853.346 | 3.150.124 | 86.53.406 |
| LM…LUU long (double length) | ||||||
| LM8LUU | 80.315 | 150.591 | 451.772 | — | — | — |
| LM10LUU | 100.394 | 190.748 | 552.165 | — | — | — |
| LM12LUU | 120.472 | 210.827 | 572.244 | — | — | — |
| LM16LUU | 160.630 | 281.102 | 702.756 | — | — | — |
| LM20LUU | 200.787 | 321.260 | 803.150 | — | — | — |
| LM25LUU | 250.984 | 401.575 | 1124.409 | — | — | — |
| LM30LUU | 301.181 | 451.772 | 1234.843 | — | — | — |
| LM40LUU | 401.575 | 602.362 | 1546.063 | — | — | — |
| LME…UU European (ISO series 3) | ||||||
| LME8UU | 80.315 | 160.630 | 250.984 | — | — | — |
| LME12UU | 120.472 | 220.866 | 321.260 | — | — | — |
| LME16UU | 160.630 | 261.024 | 361.417 | — | — | — |
| LME20UU | 200.787 | 321.260 | 451.772 | — | — | — |
| LME25UU | 250.984 | 401.575 | 582.283 | — | — | — |
| LME30UU | 301.181 | 471.850 | 682.677 | — | — | — |
| LME40UU | 401.575 | 622.441 | 803.150 | — | — | — |
No exact match. The nearest sizes:
How to read linear bushing numbers
LM 12 UU: LM = linear ball bushing, 12 = shaft diameter in mm, UU = seals at both ends (U = one seal, none = open ends). L before UU (LM12LUU) = double length with two ball circuits in one sleeve. AJ = slit sleeve for clearance adjustment; OP = open type with a segment cut away, for shafts supported along their length (the bushing D and L stay the same).
LME 12 UU is the European series for the same 12 mm shaft, but 22 mm outside and 32 mm long instead of 21 × 30 mm. LMF / LMK add a round or square flange, LMH a cut-off flange; SC / SCS are aluminium housings with an LM bushing inside.
About Linear Bearings
Inside the sleeve, rows of balls circulate in closed tracks: the loaded balls roll between the shaft and the sleeve, then return through an unloaded channel. The shaft is the inner raceway, so it must be hardened (about 60 HRC) and ground (usually to g6 for LM bushings), or the balls quickly wear grooves into it.
The housing bore for an LM bushing is normally H7. The two retaining-ring grooves (spacing B, width W, groove diameter D1) take standard external circlips to fix the bushing axially; small sizes (LM3–LM5) have no grooves.
LM8UU is the bushing of countless 3D printers and small CNC machines; the long LM8LUU on the same 8 mm rod reduces rocking on a carriage with one bushing per rod.
Load ratings vary
Dimensions are standard across THK, IKO, Samick, NB, Misumi and generic makers, but load ratings and the number of ball circuits are not. Treat ratings in shop listings with caution and take them from the maker of the part you install.
Questions
What size is an LM8UU?
8 mm shaft, 15 mm outside diameter, 24 mm long, with circlip grooves 17.5 mm apart (1.1 mm wide, 14.3 mm groove diameter).
What is the difference between LM8UU and LME8UU?
Both run on an 8 mm shaft. LM8UU is 15 × 24 mm (Asian/JIS series), LME8UU is 16 × 25 mm (European series). They need different housing bores.
What does UU mean on a linear bearing?
Rubber seals at both ends. One U means one seal; no letters means open ends.
What shaft do linear bushings need?
A hardened (about 60 HRC), ground shaft, typically g6 for LM bushings. Soft or unground rod wears quickly.
Sources
- JIS B 1514 (Asian LM series) / ISO 10285: Linear motion rolling bearings, sleeve type, boundary dimensions
- THK: Linear bushing model LM, dimensional table
- Samick: Linear bushing LM, LM-L and LME catalogue pages
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.