LED Size Chart: 3 mm, 5 mm, 10 mm and SMD 2835, 3528, 5050, 5730
SMD LED names are their size: 5050 is 5.0 × 5.0 mm, 2835 is 2.8 × 3.5 mm, 5730 is 5.7 × 3.0 mm. Through-hole LEDs are named by lens diameter (3 mm, 5 mm) with 2.54 mm lead spacing. Indicator LEDs run at around 20 mA; lighting LEDs such as 2835 and 5730 at 60–150 mA.
LED packagesTypical values; check the datasheet of your part
| Package | ⌀Diametermmin | LLengthmmin | WWidthmmin | HHeight (typical)mmin | pLead spacingmmin | Typical current | Typical power | Typical use |
|---|---|---|---|---|---|---|---|---|
| Through-hole (round) | ||||||||
| 3 mm (T-1) | 30.118 | — | — | 5.30.209 | 2.540.1000 | 20 mA | — | Indicators, panel lamps |
| 5 mm (T-1¾) | 50.197 | — | — | 8.60.339 | 2.540.1000 | 20 mA | — | Indicators, hobby projects, signs |
| 8 mm | 80.315 | — | — | — | 2.540.1000 | — | — | Larger indicators, signs |
| 10 mm | 100.394 | — | — | — | 2.540.1000 | — | — | Large indicators, decorative lighting |
| SMD packages | ||||||||
| 0402 (1005 metric) | — | 10.0394 | 0.50.0197 | — | — | — | — | Status lights on dense boards |
| 0603 (1608 metric) | — | 1.60.0630 | 0.80.0315 | — | — | — | — | Status and indicator LEDs |
| 0805 (2012 metric) | — | 20.0787 | 1.250.0492 | — | — | — | — | Indicators, easy to hand-solder |
| 1206 (3216 metric) | — | 3.20.1260 | 1.60.0630 | — | — | — | — | Indicators, backlighting |
| 3014 | — | 30.1181 | 1.40.0551 | — | — | — | — | Thin LED strips, backlights |
| 2835 | — | 2.80.1102 | 3.50.1378 | 0.80.031 | — | 60–150 mA | 0.2–0.5 W | LED strips, bulbs, panels; the common lighting LED |
| 3528 (PLCC-2) | — | 3.50.1378 | 2.80.1102 | 1.90.075 | — | 20 mA | 0.06–0.08 W | Older low-power LED strips, indicators |
| 3030 | — | 30.1181 | 30.1181 | — | — | — | — | High-power strips, high-bay and street lights |
| 4014 | — | 40.1575 | 1.40.0551 | — | — | — | — | Panels, strips |
| 5050 (PLCC-6) | — | 50.1969 | 50.1969 | 1.60.063 | — | 60 mA (3 × 20 mA) | 0.2 W | RGB and white LED strips (three chips) |
| 5630 | — | 5.60.2205 | 30.1181 | — | — | 150 mA | 0.5 W | Bulbs, tubes, strips |
| 5730 | — | 5.70.2244 | 30.1181 | — | — | 150 mA | 0.5 W | Bulbs, tubes, strips |
No exact match. The nearest sizes:
How to read LED package names
Four-digit lighting LEDs (2835, 3528, 5050, 5730 …): length and width in tenths of a millimetre. 5050 = 5.0 × 5.0 mm. The same footprint can come in several heights and powers: 2835 and 3528 share a 3.5 × 2.8 mm outline, but 2835 is about 0.8 mm thick with a large thermal pad, 3528 about 1.9 mm thick.
Chip LEDs (0402, 0603, 0805, 1206) use the inch-based EIA chip code like resistors: 0603 = 0.06 × 0.03 in = 1.6 × 0.8 mm. The metric name of 0603 is 1608; do not confuse the two systems.
Through-hole LEDs are named by lens diameter. Old lamp sizes are still used: T-1 = 3 mm, T-1¾ = 5 mm (T-sizes are in eighths of an inch). The longer lead is the anode (+); the flat on the flange marks the cathode (−).
Power class: low power ≈ 0.06–0.1 W (3528), mid power ≈ 0.2–0.5 W (2835, 5630/5730), high power ≥ 1 W (ceramic 3535 and larger). The package alone does not fix the rating. Read the datasheet.
About LED Sizes
An LED is a current-driven device: the forward voltage is almost fixed by the colour and chip material, and a small change in voltage gives a large change in current. Every LED therefore needs a current limit: a series resistor for indicators, a constant-current driver for lighting.
For indicators, 5 mm and 3 mm through-hole and 0603/0805 SMD parts are standard. Modern high-efficiency indicator LEDs are bright at 2–5 mA; the classic 20 mA figure is the test current, not a target.
For lighting, 2835 has largely replaced 3528 and 5630/5730 in strips and bulbs because it handles more power in the same footprint. 5050 houses three chips (either three whites, or red, green and blue in RGB strips) at about 20 mA each.
Heat decides lifetime. Mid-power LEDs are rated at a solder-point temperature (often 25 °C in the headline figure); on a strip without an aluminium channel they run hotter and dimmer. Derate the current if the board gets too hot to touch.
Forward voltage by colour (typical)
Typical values at rated current; check the datasheet bin. Use these for the resistor calculation and design for the maximum Vf too.
| Colour | Chip material | Typical Vf |
|---|---|---|
| Infrared (850–940 nm) | GaAs / AlGaAs | 1.2–1.6 V |
| Red | AlGaInP | 1.8–2.2 V |
| Orange / amber | AlGaInP | 1.9–2.3 V |
| Yellow | AlGaInP | 1.9–2.3 V |
| Green (old, yellow-green) | GaP | 2.0–2.4 V |
| Green (true green) | InGaN | 2.8–3.4 V |
| Blue | InGaN | 2.8–3.4 V |
| White (blue + phosphor) | InGaN | 2.8–3.4 V |
| UV (365–405 nm) | InGaN | 3.0–4.0 V |
Series resistor
R = (V supply − V f × number of LEDs in series) / I. Example: one red LED (2.0 V) at 10 mA from 5 V: (5 − 2.0) / 0.010 = 300 Ω → use 330 Ω (E12/E24), giving 9.1 mA. Resistor power: (5 − 2.0) × 0.0091 ≈ 27 mW, fine for a 1/8 W part.
Do not put LEDs in parallel on one resistor: the one with the lowest Vf takes most of the current. Give each string its own resistor.
LED strip voltages
12 V strips put three white LEDs (about 3 × 3.1 V) in series with one resistor per segment, so they can be cut every 3 LEDs; 24 V strips use six or seven in series and can be cut every 6–7 LEDs. 5 V strips (including addressable WS2812B, which is a 5050 package) have one LED per segment.
Questions
What size is a 5050 LED?
5.0 × 5.0 mm, about 1.6 mm high. It contains three LED chips, so it is used for RGB strips or bright white strips; typical current 60 mA (3 × 20 mA), about 0.2 W.
What is the difference between 2835 and 3528 LEDs?
Same 3.5 × 2.8 mm footprint, but 2835 is a thinner (about 0.8 mm) mid-power package with a large thermal pad, typically 0.2–0.5 W, while 3528 is about 1.9 mm high and runs at about 20 mA (≈ 0.07 W). 2835 gives roughly three times the light per LED.
How much current does a 5 mm LED need?
Standard 5 mm indicator LEDs are rated for 20 mA continuous (some up to 30 mA). Modern ones are clearly visible at 2–5 mA, which saves power and heat.
What resistor do I need for an LED on 12 V?
For one white LED (about 3.1 V) at 20 mA: (12 − 3.1) / 0.02 = 445 Ω → 470 Ω, dissipating about 0.17 W, so use a 1/4 W resistor. For a red LED (2.0 V): (12 − 2) / 0.02 = 500 Ω → 510 Ω.
Which leg of an LED is positive?
The longer leg is the anode (+). The cathode (−) is the shorter leg and sits next to the flat on the rim. On SMD LEDs the cathode is marked by a notch, a green dot or a T-shaped mark on the underside. Check the datasheet, because conventions differ.
Sources
- Kingbright: through-hole LED lamps (T-1, T-1¾) and SMD chip LED datasheets
- Everlight: 3 mm / 5 mm LED lamp and PLCC LED datasheets
- Samsung LED: mid-power LM281B (2835), LM301B (3030) datasheets
- Lumileds: LUXEON mid-power LED datasheets
- EIA / JEDEC chip size codes (0402, 0603, 0805, 1206)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.