SMD Package Sizes: Chip Codes, SOT, SOIC, QFN, TO

Body size, lead pitch and pin count of the packages on a circuit board, from 0.4 mm chip resistors to TO-247 power transistors. The most common mix-up: chip codes exist in inches and millimetres. An imperial 0603 is 1.6 × 0.8 mm, while a metric 0603 is the tiny imperial 0201.

49 packagesChecked 2026-11-156 sources
010050402M02010603M04021005M06031608M08052012M12063216M12103225M18124532M20105025M25126332M1 mm
Imperial code above, metric code below. The bar is 1 mm.Drawn to scale · Dimensions in mmDimensions in inches

Package chartTap a package for its drawing

49 of 49 packages
PackageMetric codeLBody lengthmminWBody widthmminEWidth over leadsmminHHeight (max.; chips: typ.)mminePitchmminPinsPower rating (thick-film, typ.)W
Chip resistors and capacitors
010050402M0.40.0160.20.008—0.130.005—20.031
02010603M0.60.0240.30.012—0.230.009—20.05
04021005M10.0390.50.020—0.350.014—20.0625
06031608M1.60.0630.80.031—0.450.018—20.1
08052012M20.0791.250.049—0.50.020—20.125
12063216M3.20.1261.60.063—0.550.022—20.25
12103225M3.20.1262.50.098—0.550.022—20.5
18124532M4.50.1773.20.126———20.75
20105025M50.1972.50.098—0.550.022—20.75
25126332M6.30.2483.20.126—0.550.022—21
Diodes and small transistors
SOD-123—2.70.1061.60.0633.70.1461.350.053—2—
SOD-323—1.70.0671.250.0492.50.0981.10.043—2—
SOD-523—1.20.0470.80.0311.60.0630.70.028—2—
SOT-23—2.90.1141.30.0512.1–2.640.083–0.1041.120.0440.950.0373—
SOT-23-5—2.90.1141.60.0632.80.1101.450.0570.950.0375—
SOT-23-6—2.90.1141.60.0632.80.1101.450.0570.950.0376—
SOT-323 (SC-70)—20.0791.250.0492.10.0831.10.0430.650.0263—
SOT-363 (SC-88)—20.0791.250.0492.10.0831.10.0430.650.0266—
SOT-563—1.60.0631.20.0471.60.0630.60.0240.50.0206—
Power SMD packages
SOT-89—4.50.1772.50.098—1.60.0631.50.0593—
SOT-223—6.50.2563.50.13870.2761.80.0712.30.0914—
TO-252 (DPAK)—6.60.2606.10.2409.35–10.40.368–0.4092.390.0942.280.0903—
TO-263 (D2PAK)—10.10.398—14.6–15.90.575–0.626—2.540.1003—
Through-hole packages
TO-92—4.45–5.20.175–0.2053.18–4.190.125–0.165—4.32–5.330.170–0.2101.270.0503—
TO-220—100.3944.3–4.70.169–0.185——2.540.1003—
TO-247—15.90.62650.197——5.450.2153—
DIP-8—9.02–10.160.355–0.4006.350.2507.620.3005.330.2102.540.1008—
DIP-14—18.67–19.690.735–0.7756.350.2507.620.3005.330.2102.540.10014—
DIP-16—18.67–19.690.735–0.7756.350.2507.620.3005.330.2102.540.10016—
IC packages
SOIC-8—4.90.1933.90.15460.2361.750.0691.270.0508—
SOIC-14—8.650.3413.90.15460.2361.750.0691.270.05014—
SOIC-16 (narrow)—9.90.3903.90.15460.2361.750.0691.270.05016—
SOIC-16 (wide)—10.30.4067.50.29510.30.4062.650.1041.270.05016—
TSSOP-8—30.1184.40.1736.40.2521.20.0470.650.0268—
TSSOP-14—50.1974.40.1736.40.2521.20.0470.650.02614—
TSSOP-16—50.1974.40.1736.40.2521.20.0470.650.02616—
TSSOP-20—6.50.2564.40.1736.40.2521.20.0470.650.02620—
MSOP-8—30.11830.1184.90.1931.10.0430.650.0268—
QFN-16 (3×3 mm)—30.11830.118—10.0390.50.02016—
QFN-20 (4×4 mm)—40.15740.157—10.0390.50.02020—
QFN-24 (4×4 mm)—40.15740.157—10.0390.50.02024—
QFN-32 (5×5 mm)—50.19750.197—10.0390.50.02032—
QFN-48 (7×7 mm)—70.27670.276—10.0390.50.02048—
LQFP-32—70.27670.27690.3541.60.0630.80.03132—
LQFP-44—100.394100.394120.4721.60.0630.80.03144—
LQFP-48—70.27670.27690.3541.60.0630.50.02048—
LQFP-64—100.394100.394120.4721.60.0630.50.02064—
LQFP-100—140.551140.551160.6301.60.0630.50.020100—
LQFP-144—200.787200.787220.8661.60.0630.50.020144—

How to read package names and dimensions

Chip codes give length and width. The imperial (EIA) code is in hundredths of an inch: 0805 = 0.08 × 0.05 in. The metric code is in tenths of a millimetre: 2012 = 2.0 × 1.25 mm, the same part. US and most distributor listings use the imperial code; Japanese makers often use metric. When only four digits are given and the size matters, check which system: the codes 0402 and 0603 exist in both and mean different parts.

For leaded packages, L is the body length along the rows of pins, W the body width, and E the tip-to-tip width over the leads, which is the width your PCB footprint must allow for (for DIP, E is the 7.62 mm spacing between the two lead rows). e is the lead pitch (centre to centre). H is the maximum seated height above the board.

The number after a package name is the pin count (SOIC-8, TSSOP-20, LQFP-64). The body size of QFN and LQFP is not fixed by the pin count (a QFN-20 comes in 3 × 3 and 4 × 4 mm), so check the datasheet's package code (for example TI "RGT", "PW", "DBV") before laying out a board.

Values here are nominal. Use the land pattern from the part's datasheet or IPC-7351 for the actual footprint. Pads are larger than the leads.

About SMD & IC Packages

Surface-mount resistors and ceramic capacitors share the same case sizes. The power rating in the chart is the typical value for general-purpose thick-film resistors at 70 °C; anti-surge, thin-film and metal-strip parts in the same size can differ. Capacitor height depends on capacitance and voltage (a 22 µF 0805 can be 1.25 mm thick), so it is not listed.

For hand soldering, 0805 and 1206 are comfortable, 0603 is manageable with tweezers and a fine tip, and 0402 and smaller need magnification and practice. Pitch is the limit for ICs: 1.27 mm SOIC is easy, 0.65 mm TSSOP needs a fine tip and flux, 0.5 mm QFN with an exposed pad needs hot air or reflow.

Many packages have several names. SOT-23 is JEDEC TO-236; SOT-323 is SC-70; SOT-363 is SC-88; SOT-23-5 is also called SOT-25 or SC-74A; DPAK is TO-252 and D2PAK is TO-263. Manufacturers add their own codes on top (TI "DBV" for SOT-23-5, Maxim "µMAX" for MSOP).

Leaded package outlines are taken from the JEDEC registered outlines in JEP95; within one JEDEC variant, dimensions match across manufacturers to the tolerance given in the outline drawing.

Thermal pads and power packages

QFN, DPAK, D2PAK, SOT-89 and SOT-223 move heat through a large tab or exposed pad soldered to the board. Their power rating depends almost entirely on copper area: a SOT-223 manages around 1 W on a small pad and noticeably more on a large copper pour. Use the thermal resistance θJA from the datasheet for the board layout you plan.

Through-hole pitch

DIP packages use 2.54 mm (0.1 in) pitch with rows 7.62 mm (0.3 in) apart, so they fit breadboards and stripboard. TO-92 leads are 1.27 mm apart as moulded; many parts ship with the leads formed to 2.54 mm. TO-220 uses 2.54 mm and TO-247 5.45 mm lead pitch.

Questions

What size is an 0603 resistor?

An imperial 0603 is 1.6 × 0.8 mm (0.063 × 0.031 in), about 0.45 mm thick, rated 1/10 W as a thick-film resistor. Its metric code is 1608. A metric 0603 is the imperial 0201: 0.6 × 0.3 mm.

What is the difference between 0402 and 0603?

0402 is 1.0 × 0.5 mm, 0603 is 1.6 × 0.8 mm (imperial codes). 0603 has about 2.5 times the area, is easier to hand-solder and is typically rated 1/10 W against 1/16 W.

What are the dimensions of SOT-23?

Body 2.9 × 1.3 mm, 2.1–2.64 mm over the leads, 0.95 mm pitch between adjacent pins (1.9 mm between pins 1 and 2), maximum height 1.12 mm for TO-236AB.

What is the difference between SOIC and TSSOP?

SOIC has 1.27 mm pitch and a 3.9 mm (narrow) or 7.5 mm (wide) body. TSSOP has 0.65 mm pitch and a 4.4 mm body, about half the board area and 1.2 mm high instead of 1.75 mm.

How much power can a 1206 resistor handle?

A standard thick-film 1206 is rated 1/4 W at 70 °C ambient, derating to zero at 155 °C. High-power 1206 series reach 1/2 W; check the datasheet.

Sources

  1. JEDEC JEP95: JEDEC Registered and Standard Outlines for Semiconductor Devices
  2. IEC 60115-8 / EIA-576: Fixed chip resistors, case sizes
  3. Yageo: RC series general purpose chip resistors datasheet
  4. Vishay: CRCW thick film chip resistors datasheet
  5. Texas Instruments: Package outline drawings (DBV, DCK, D, PW, DGK, RGT, PM)
  6. Nexperia: Package information (SOT23, SOT323, SOT363, SOD123, SOD323, SOT89, SOT223)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.