Resistor Color Code Chart and Calculator: 4, 5 and 6 Bands, E-Series, SMD Codes
Read a resistor from the end where the bands are bunched together: digits first, then the multiplier, then tolerance. Yellow-violet-red-gold is 4 7 × 100 = 4.7 kΩ ±5 %. Five-band resistors have three digits (brown-black-black-red-brown = 10.0 kΩ ±1 %); a sixth band gives the temperature coefficient.
Color codeDigit, multiplier, tolerance and tempco of every band color
| Color | Swatch | Digit | Multiplier | Tolerance (letter) | Temp. coefficient (6th band) |
|---|---|---|---|---|---|
| Black | #1B1B1B | 0 | ×1 | — | 250 ppm/K |
| Brown | #7A4A24 | 1 | ×10 | ±1 % (F) | 100 ppm/K |
| Red | #D8261F | 2 | ×100 | ±2 % (G) | 50 ppm/K |
| Orange | #F08A1C | 3 | ×1 k | ±0.05 % (W) | 15 ppm/K |
| Yellow | #F4CF1A | 4 | ×10 k | ±0.02 % (P) | 25 ppm/K |
| Green | #2E9A43 | 5 | ×100 k | ±0.5 % (D) | 20 ppm/K |
| Blue | #1F5FBF | 6 | ×1 M | ±0.25 % (C) | 10 ppm/K |
| Violet | #7B4FB3 | 7 | ×10 M | ±0.1 % (B) | 5 ppm/K |
| Grey | #8A8D91 | 8 | ×100 M | ±0.01 % (L) | 1 ppm/K |
| White | #F3F1EA | 9 | ×1 G | — | — |
| Gold | #C9A227 | — | ×0.1 | ±5 % (J) | — |
| Silver | #B8BCC2 | — | ×0.01 | ±10 % (K) | — |
| Pink | #F19BBF | — | ×0.001 | — | — |
| None (no band) | — | — | — | ±20 % (M) | — |
No exact match. The nearest sizes:
How to read the bands
Find the start. The tolerance band (gold, silver, brown …) is usually set a little apart or is wider; start from the other end. Gold and silver are never first bands. If in doubt, check both readings against the E-series: only one of them is normally a standard value.
4 bands: digit, digit, multiplier, tolerance. Red-red-orange-gold = 22 × 1000 = 22 kΩ ±5 %.
5 bands: digit, digit, digit, multiplier, tolerance. Used on 1 % and better metal-film resistors. Orange-orange-black-brown-brown = 330 × 10 = 3.30 kΩ ±1 %.
6 bands: as 5 bands plus temperature coefficient in ppm/K (brown 100, red 50, yellow 25, orange 15, blue 10, violet 5).
3 bands (old carbon resistors): digit, digit, multiplier, no tolerance band = ±20 %. A single black band marks a 0 Ω jumper.
Gold and silver multipliers give values below 10 Ω: green-blue-gold = 5.6 Ω; brown-black-silver = 0.10 Ω.
About Resistor Color Codes
The color code is defined in IEC 60062. Each color is a digit 0–9 in the same order as the visible spectrum after black and brown: black 0, brown 1, red 2, orange 3, yellow 4, green 5, blue 6, violet 7, grey 8, white 9. As a multiplier the color is the power of ten; gold ×0.1, silver ×0.01.
Values are not arbitrary: they come from the E series of IEC 60063, geometric series with 6, 12, 24, 48, 96 or 192 values per decade. A ±5 % resistor is almost always an E24 value (10, 11, 12, 13, 15, 16 …), a ±1 % resistor an E96 value (100, 102, 105 …). If the bands give 4.8 kΩ you have read them wrongly; 4.7 kΩ is the E24 value.
Colors fade and heat-darken: brown, red and orange are easy to confuse, and violet can look grey. Measure with a meter when it matters, out of circuit, since parallel paths on a board make in-circuit readings low.
Surface-mount resistors carry a printed code instead (or nothing, on 0402 and smaller). The tool decodes 3-digit (±5 %), 4-digit (±1 %) and EIA-96 codes; the tables below list the series.
Tolerance letters
The tolerance letter is also used in part numbers and on capacitors: B ±0.1 %, C ±0.25 %, D ±0.5 %, F ±1 %, G ±2 %, J ±5 %, K ±10 %, M ±20 %. Orange (±0.05 %, W) and yellow (±0.02 %, P) were added as tolerance colors in IEC 60062:2016; older charts leave them blank.
E6, E12 and E24 values
Multiply by any power of ten: E12 4.7 → 4.7 Ω, 47 Ω, 470 Ω, 4.7 kΩ …
| Series | Tolerance | Values per decade |
|---|---|---|
| E6 | ±20 % | 1.0, 1.5, 2.2, 3.3, 4.7, 6.8 |
| E12 | ±10 % | 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 8.2 |
| E24 | ±5 % | 1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.8, 2.0, 2.2, 2.4, 2.7, 3.0, 3.3, 3.6, 3.9, 4.3, 4.7, 5.1, 5.6, 6.2, 6.8, 7.5, 8.2, 9.1 |
E48 values (±2 %)
| 100 | 105 | 110 | 115 | 121 | 127 | 133 | 140 | 147 | 154 | 162 | 169 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 178 | 187 | 196 | 205 | 215 | 226 | 237 | 249 | 261 | 274 | 287 | 301 |
| 316 | 332 | 348 | 365 | 383 | 402 | 422 | 442 | 464 | 487 | 511 | 536 |
| 562 | 590 | 619 | 649 | 681 | 715 | 750 | 787 | 825 | 866 | 909 | 953 |
E96 values (±1 %)
| 100 | 102 | 105 | 107 | 110 | 113 | 115 | 118 | 121 | 124 | 127 | 130 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 133 | 137 | 140 | 143 | 147 | 150 | 154 | 158 | 162 | 165 | 169 | 174 |
| 178 | 182 | 187 | 191 | 196 | 200 | 205 | 210 | 215 | 221 | 226 | 232 |
| 237 | 243 | 249 | 255 | 261 | 267 | 274 | 280 | 287 | 294 | 301 | 309 |
| 316 | 324 | 332 | 340 | 348 | 357 | 365 | 374 | 383 | 392 | 402 | 412 |
| 422 | 432 | 442 | 453 | 464 | 475 | 487 | 499 | 511 | 523 | 536 | 549 |
| 562 | 576 | 590 | 604 | 619 | 634 | 649 | 665 | 681 | 698 | 715 | 732 |
| 750 | 768 | 787 | 806 | 825 | 845 | 866 | 887 | 909 | 931 | 953 | 976 |
SMD resistor codes
3 digits (usually ±5 %, E24): two digits and a multiplier. 472 = 47 × 10² = 4.7 kΩ; 100 = 10 Ω; 000 or 0 = 0 Ω jumper.
4 digits (usually ±1 %): three digits and a multiplier. 4701 = 470 × 10 = 4.7 kΩ; 1002 = 10 kΩ.
R marks the decimal point: 4R7 = 4.7 Ω, R100 = 0.1 Ω. Current-sense resistors may use m for milliohms (5m0 = 5 mΩ).
EIA-96 (±1 %, small 0603 parts): two digits give the position in the E96 series, a letter the multiplier: Z ×0.001, Y or R ×0.01, X or S ×0.1, A ×1, B or H ×10, C ×100, D ×1000, E ×10 000, F ×100 000. 01C = 100 × 100 = 10 kΩ; 68X = 499 × 0.1 = 49.9 Ω.
EIA-96 code table
| Code | Value | Code | Value | Code | Value | Code | Value |
|---|---|---|---|---|---|---|---|
| 01 | 100 | 25 | 178 | 49 | 316 | 73 | 562 |
| 02 | 102 | 26 | 182 | 50 | 324 | 74 | 576 |
| 03 | 105 | 27 | 187 | 51 | 332 | 75 | 590 |
| 04 | 107 | 28 | 191 | 52 | 340 | 76 | 604 |
| 05 | 110 | 29 | 196 | 53 | 348 | 77 | 619 |
| 06 | 113 | 30 | 200 | 54 | 357 | 78 | 634 |
| 07 | 115 | 31 | 205 | 55 | 365 | 79 | 649 |
| 08 | 118 | 32 | 210 | 56 | 374 | 80 | 665 |
| 09 | 121 | 33 | 215 | 57 | 383 | 81 | 681 |
| 10 | 124 | 34 | 221 | 58 | 392 | 82 | 698 |
| 11 | 127 | 35 | 226 | 59 | 402 | 83 | 715 |
| 12 | 130 | 36 | 232 | 60 | 412 | 84 | 732 |
| 13 | 133 | 37 | 237 | 61 | 422 | 85 | 750 |
| 14 | 137 | 38 | 243 | 62 | 432 | 86 | 768 |
| 15 | 140 | 39 | 249 | 63 | 442 | 87 | 787 |
| 16 | 143 | 40 | 255 | 64 | 453 | 88 | 806 |
| 17 | 147 | 41 | 261 | 65 | 464 | 89 | 825 |
| 18 | 150 | 42 | 267 | 66 | 475 | 90 | 845 |
| 19 | 154 | 43 | 274 | 67 | 487 | 91 | 866 |
| 20 | 158 | 44 | 280 | 68 | 499 | 92 | 887 |
| 21 | 162 | 45 | 287 | 69 | 511 | 93 | 909 |
| 22 | 165 | 46 | 294 | 70 | 523 | 94 | 931 |
| 23 | 169 | 47 | 301 | 71 | 536 | 95 | 953 |
| 24 | 174 | 48 | 309 | 72 | 549 | 96 | 976 |
Questions
What color code is a 10k resistor?
4-band: brown-black-orange-gold (1 0 × 1000, ±5 %). 5-band: brown-black-black-red-brown (100 × 100, ±1 %).
What color code is a 220 ohm resistor?
4-band: red-red-brown-gold (22 × 10 = 220 Ω, ±5 %). 5-band: red-red-black-black-brown (220 × 1, ±1 %).
What color code is a 1k resistor?
4-band: brown-black-red-gold (10 × 100 = 1 kΩ). 5-band: brown-black-black-brown-brown (100 × 10 = 1.00 kΩ, ±1 %).
Which side do you start reading a resistor?
From the end with the bands closest together, away from the gold or silver tolerance band. On 5-band resistors with a brown tolerance band, the gap before the last band is wider; if unsure, the reading that gives an E-series value is the right one.
What does a resistor with one black band mean?
It is a 0 Ω link (jumper), used where an automatic inserter places a wire bridge. SMD jumpers are marked 0 or 000.
What is the SMD code for 4.7k?
472 (3-digit, ±5 %) or 4701 (4-digit, ±1 %). EIA-96 has no exact 4.7 kΩ: the nearest E96 value is 475 (position 66), so 4.75 kΩ is marked 66B.
Sources
- IEC 60062:2016, Marking codes for resistors and capacitors
- IEC 60063:2015, Preferred number series for resistors and capacitors (E series)
- Vishay: Resistor colour code and E-series application note
- Yageo / Panasonic: chip resistor marking (3-digit, 4-digit and EIA-96 codes)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.