Motorcycle Chain Sizes: 415, 420, 428, 520, 525, 530, 532, 630
A motorcycle chain number gives pitch and width: the first digit is the pitch in eighths of an inch (4 = 1/2 in, 5 = 5/8 in), the rest the width class. A 520 chain is 5/8 in pitch and 1/4 in wide inside; 525 and 530 have the same pitch but are 5/16 and 3/8 in wide. Sprockets must match both pitch and width.
Size chartTap a size for its drawing and full specs
| Size | pPitchmmin | b1Inner widthmmin | d1Roller diametermmin | Typical bikes |
|---|---|---|---|---|
| 1/2 in pitch | ||||
| 415 chain | 12.71/2 | 4.763/16 | 7.750.305 | mopeds, 50 cc racing and pit bikes |
| 420 chain | 12.71/2 | 6.351/4 | 7.770.306 | 50–110 cc: small dirt bikes, mopeds, scooters |
| 428 chain | 12.71/2 | 7.945/16 | 8.510.335 | 100–250 cc: small road bikes, 125 cc dirt bikes |
| 5/8 in pitch | ||||
| 520 chain | 15.8755/8 | 6.351/4 | 10.160.400 | 250–600 cc road bikes, most dirt bikes 125 cc and up, track conversions |
| 525 chain | 15.8755/8 | 7.945/16 | 10.160.400 | 600–1000 cc sport and touring bikes |
| 530 chain | 15.8755/8 | 9.523/8 | 10.160.400 | 750 cc and up, older large bikes, heavy sport bikes |
| 532 chain | 15.8755/8 | 9.523/8 | 11.100.437 | older large bikes (larger rollers than 530) |
| 3/4 in pitch | ||||
| 630 chain | 19.053/4 | 9.523/8 | 11.910.469 | older large-capacity bikes (1970s–80s) |
No exact match. The nearest sizes:
Reading the size and choosing a chain
The number is read as pitch digit + width code: 5|20, 5|25, 5|30. The pitch is the distance between pin centers; measure it over several links (for example 10 pitches of a 520 chain = 6.25 in, 158.75 mm) because a worn chain is longer. The inner width is between the inner plates, which matches the sprocket tooth width.
Within one pitch, a wider chain is stronger and heavier. 520 is the lightest of the 5/8 in sizes and is used on dirt bikes and as a 'conversion' on road bikes for less rotating weight; 530 is the heaviest. Changing between 520, 525 and 530 needs new front and rear sprockets.
Chains come as standard (no seals), O-ring, X-ring or similar sealed types, which keep grease in the pins and last several times longer. Length is given in links (e.g. 520 × 120). Riveted master links are preferred over clip links on powerful bikes.
About Motorcycle Chains
Motorcycle chains use the ANSI pitch system but are built with thicker plates, hardened pins and seals, so a 530 motorcycle chain and an industrial ANSI 50 chain share a pitch and roller size but are not the same chain. Fit only chains made for motorcycles to a motorcycle.
The bike maker specifies chain size, link count and often the strength grade. Change chain and both sprockets together: a new chain on worn sprockets wears quickly and skips. A chain is usually worn out when it can be pulled away from the rear sprocket at the 3 o'clock position by more than about half a tooth, or when 20 pitches measure more than the maker's limit.
Dimensions in the chart are pitch, inner width and roller diameter, which decide sprocket fit. Pin diameter, plate height and tensile strength differ between grades and makers and are left out.
Questions
What does 520 mean on a motorcycle chain?
5 = 5/8 in pitch (15.875 mm), 20 = 1/4 in (6.35 mm) inner width. 525 is 5/16 in wide and 530 is 3/8 in wide at the same pitch.
Can I put a 520 chain on 525 sprockets?
No. The pitch is the same but the width differs; use sprockets of the same width as the chain.
What size chain does a 125 cc motorcycle use?
Usually 428 on road bikes and 520 on 125 cc dirt bikes; check the manual or the number stamped on the side plates.
How do I measure chain size?
Measure pin center to pin center over several links and divide (1/2 in or 5/8 in pitch), then measure between the inner plates: 1/4, 5/16 or 3/8 in. The size is also stamped on the link plates.
Sources
- D.I.D: Motorcycle chain size and dimension table
- RK Excel: Chain dimensions (pitch, inner width, roller diameter)
- ASME B29.1: Precision power transmission roller chains (ANSI 40/50/60 base dimensions)
- Wikipedia: Roller chain (ANSI numbering)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.