Roller Chain Size Chart
A roller chain is identified by its pitch, roller diameter and inner width. ANSI chain numbers encode the pitch in eighths of an inch (#40 = 4/8 = 1/2 in); ISO B-series codes give it in sixteenths (08B = 8/16 = 1/2 in). #40 and 08B share the pitch but not the roller or width, so they do not run on each other's sprockets.
Chain chartTap a chain for its drawing and full specs
| Chain | pPitchmmin | d1Roller diametermmin | b1Inner widthmmin | d2Pin diametermmin | h2Plate height (max.)mmin | FuMin. tensile strengthkNlbf | ISO 606 code |
|---|---|---|---|---|---|---|---|
| ANSI / ASME B29.1 (ISO 606 A series) | |||||||
| #25 | 6.350.250 | 3.300.130 | 3.180.125 | 2.300.091 | 6.020.237 | — | 04C |
| #35 | 9.5250.375 | 5.080.200 | 4.780.188 | 3.580.141 | 9.050.356 | — | 06C |
| #40 | 12.70.500 | 7.920.312 | 7.920.312 | 3.960.156 | 12.070.475 | — | 08A |
| #41 | 12.70.500 | 7.770.306 | 6.350.250 | 3.580.141 | 9.910.390 | — | 085 |
| #50 | 15.8750.625 | 10.160.400 | 9.530.375 | 5.080.200 | 15.090.594 | — | 10A |
| #60 | 19.050.750 | 11.910.469 | 12.700.500 | 5.940.234 | 18.080.712 | — | 12A |
| #80 | 25.41.000 | 15.880.625 | 15.880.625 | 7.920.312 | 24.130.950 | — | 16A |
| #100 | 31.751.250 | 19.050.750 | 19.050.750 | 9.530.375 | 30.181.188 | — | 20A |
| #120 | 38.11.500 | 22.230.875 | 25.401.000 | 11.100.437 | 36.201.425 | — | 24A |
| #140 | 44.451.750 | 25.401.000 | 25.401.000 | 12.700.500 | 42.241.663 | — | 28A |
| #160 | 50.82.000 | 28.581.125 | 31.751.250 | 14.270.562 | 48.261.900 | — | 32A |
| #180 | 57.152.250 | 35.711.406 | 35.711.406 | 17.450.687 | 54.302.138 | — | 36A |
| #200 | 63.52.500 | 39.671.562 | 38.101.500 | 19.840.781 | 60.332.375 | — | 40A |
| #240 | 76.23.000 | 47.631.875 | 47.631.875 | 23.800.937 | 72.392.850 | — | 48A |
| ISO 606 B series (BS 228 / DIN 8187, European) | |||||||
| 04B | 60.236 | 4.000.157 | 2.800.110 | 1.850.073 | 5.000.197 | 3.0674 | 04B |
| 05B | 80.315 | 5.000.197 | 3.000.118 | 2.310.091 | 7.110.280 | 4.4989 | 05B |
| 06B | 9.5250.375 | 6.350.250 | 5.720.225 | 3.280.129 | 8.260.325 | 8.92,001 | 06B |
| 08B | 12.70.500 | 8.510.335 | 7.750.305 | 4.450.175 | 11.810.465 | 17.84,002 | 08B |
| 10B | 15.8750.625 | 10.160.400 | 9.650.380 | 5.080.200 | 14.730.580 | 22.24,991 | 10B |
| 12B | 19.050.750 | 12.070.475 | 11.680.460 | 5.720.225 | 16.130.635 | 28.96,497 | 12B |
| 16B | 25.41.000 | 15.880.625 | 17.020.670 | 8.280.326 | 21.080.830 | 60.013,489 | 16B |
| 20B | 31.751.250 | 19.050.750 | 19.560.770 | 10.190.401 | 26.421.040 | 95.021,357 | 20B |
| 24B | 38.11.500 | 25.401.000 | 25.401.000 | 14.630.576 | 33.401.315 | 160.035,969 | 24B |
| 28B | 44.451.750 | 27.941.100 | 30.991.220 | 15.900.626 | 37.081.460 | 200.044,962 | 28B |
| 32B | 50.82.000 | 29.211.150 | 30.991.220 | 17.810.701 | 42.291.665 | 250.056,202 | 32B |
| 40B | 63.52.500 | 39.371.550 | 38.101.500 | 22.890.901 | 52.962.085 | 355.079,807 | 40B |
| 48B | 76.23.000 | 48.261.900 | 45.721.800 | 29.241.151 | 63.882.515 | 560.0125,893 | 48B |
No exact match. The nearest sizes:
How to read a chain number
ANSI chains (ASME B29.1): the digits before the last one give the pitch in eighths of an inch: #40 is 4/8 = 1/2 in, #60 is 6/8 = 3/4 in, #100 is 10/8 = 1-1/4 in. The last digit is the type: 0 = standard roller chain, 1 = lightweight (#41), 5 = rollerless bushing chain (#25, #35). Suffixes: -2, -3 for double and triple strand (40-2), H for heavy series with thicker plates (80H), SS for stainless steel, O-ring or X-ring for sealed chains. Brands add letters in front: RS40 (Tsubaki), C40, 40-1R.
ISO B-series chains (British Standard, DIN 8187): the number before the B is the pitch in sixteenths of an inch: 08B is 8/16 = 1/2 in, 16B is 1 in. A suffix -1, -2, -3 gives the number of strands (08B-2 duplex). Metric B-series chains are common in Europe, Asia and on imported machinery; the 04B and 05B have metric pitches (6 and 8 mm).
To identify a chain, measure the pitch over several links (centre of one pin to the centre of the pin 10 pitches away, divided by 10), then the roller diameter and the inner width between the inner plates. Pitch alone is not enough: at 1/2 in pitch, #40 has a 7.92 mm roller and 7.92 mm inner width, #41 a 7.77 mm roller and 6.35 mm width, 08B an 8.51 mm roller and 7.75 mm width.
About Roller Chains
Two families of short-pitch transmission chain dominate: the American ANSI series, standardised in ASME B29.1 and adopted by ISO 606 as the A series, and the British B series (BS 228, DIN 8187, ISO 606 B). Most pitches exist in both, but rollers, plate thickness and inner widths differ, so the chains and sprockets are not interchangeable. A B-series chain on an ANSI sprocket wears both rapidly or climbs the teeth.
The chart gives the dimensions that decide fit: pitch p, roller diameter d1, inner width b1 (the space for the sprocket tooth), pin diameter d2 and maximum plate height h2 (which matters for chain guides and clearance). ANSI values are the nominal inch dimensions converted to mm; B-series values are ISO 606 limits (maximum roller and pin diameter, minimum inner width, maximum plate height).
Minimum tensile strength is listed for the ISO B series from ISO 606. For ANSI chains it is left out: ASME B29.1 raised its minimum values in 2011 and catalogues still mix old and new figures. Average breaking loads of brand-name chains are well above both. Take working loads from the manufacturer's power rating tables, not from the breaking load.
#25 and #35: bushing chains
The two smallest ANSI sizes have no separate rollers: the bushing itself contacts the sprocket. The value in the roller-diameter column is the bushing diameter (0.130 in for #25, 0.200 in for #35). They run quietly at high speed but wear faster than true roller chain under load. #35 is the classic chain for go-karts, small engines and light conveyors.
#41: the lightweight 1/2 in chain
#41 has the same 1/2 in pitch as #40 but a narrower inner width (1/4 in instead of 5/16 in), a smaller roller (0.306 in) and thinner, lower plates. It suits light-duty drives such as small conveyors, garage door openers and farm equipment. It needs its own #41 sprockets: a #41 chain is too narrow for #40 teeth, and #40 chain is too wide for #41 sprockets.
Motorcycle and bicycle chains
Motorcycle chains (420, 428, 520, 525, 530 …) use ANSI pitches (the first digit is the pitch in eighths, the rest the width) but have their own widths and much stronger plates. Bicycle chains are 1/2 in pitch with 1/8 in or 3/32 in inner width. Neither is covered by this chart.
Questions
What is the pitch of #40 chain?
1/2 in (12.7 mm). The first digit(s) of an ANSI number are the pitch in eighths of an inch: 4/8 in. #50 is 5/8 in, #60 3/4 in, #80 1 in.
Is 08B the same as #40 chain?
No. Both have a 1/2 in pitch, but 08B has an 8.51 mm roller and 7.75 mm inner width, #40 a 7.92 mm roller and 7.92 mm inner width. They need different sprockets.
What is the difference between #40 and #41 chain?
Same 1/2 in pitch, but #41 is narrower (1/4 in vs 5/16 in inner width), has a smaller roller (0.306 vs 0.312 in) and lighter plates. #41 is weaker and needs #41 sprockets.
How do I measure roller chain size?
Measure across 10 pitches (pin centre to pin centre) and divide by 10 for the pitch. Then measure the roller diameter and the inner width between the inner plates. Compare all three with the chart. The pitch alone does not tell ANSI from B series.
What does 40-2 mean?
Double-strand (duplex) #40 chain: two rows of rollers sharing long pins. 40-3 is triple strand. The ISO equivalents are written 08B-2, 08B-3.
What is #35 chain used for?
#35 (3/8 in pitch, rollerless bushing chain) is used on go-karts, minibikes, small engines and light conveyors. It runs smoothly at high speed but is lighter duty than #40.
Sources
- ASME B29.1-2011: Precision power transmission roller chains, attachments and sprockets
- ISO 606:2015, Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets
- Tsubaki: Drive chain catalogue, ANSI and BS/DIN roller chain dimensions
- Renold: Roller chain catalogue, ISO 606 B series
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.