3D Printer Nozzle Size Chart: Layer Heights, Line Widths and Thread Types
Layer height should stay between about 25 % and 75 % of the nozzle diameter: a standard 0.4 mm nozzle prints 0.1–0.3 mm layers, a 0.6 mm nozzle 0.15–0.45 mm. E3D V6, Volcano and MK8 nozzles all screw in with an M6 × 1 thread but differ in length, so they are not interchangeable between heater blocks.
Size chartSort by any column, or filter to find a row
| Nozzle | Nozzle diametermmin | Layer height (25–75 %)mmin | Line width (100–120 %)mmin | Thread | Wrench sizemm | Overall lengthmmin | Typical use |
|---|---|---|---|---|---|---|---|
| Nozzle diameters | |||||||
| 0.15 mm | 0.150.006 | 0.04–0.110.002–0.004 | 0.15–0.180.006–0.007 | — | — | — | Miniatures and very fine detail; slow, clogs easily, needs clean filament |
| 0.2 mm | 0.20.008 | 0.05–0.150.002–0.006 | 0.2–0.240.008–0.009 | — | — | — | Miniatures and very fine detail; slow, clogs easily, needs clean filament |
| 0.25 mm | 0.250.01 | 0.06–0.190.002–0.007 | 0.25–0.30.01–0.012 | — | — | — | Fine detail and small text with faster printing than 0.2 mm |
| 0.3 mm | 0.30.012 | 0.08–0.220.003–0.009 | 0.3–0.360.012–0.014 | — | — | — | Fine detail and small text with faster printing than 0.2 mm |
| 0.4 mm | 0.40.016 | 0.1–0.30.004–0.012 | 0.4–0.480.016–0.019 | — | — | — | Standard nozzle on almost every printer; the best all-round balance |
| 0.5 mm | 0.50.02 | 0.13–0.380.005–0.015 | 0.5–0.60.02–0.024 | — | — | — | Faster prints and stronger parts with little loss of detail; good for PETG and functional parts |
| 0.6 mm | 0.60.024 | 0.15–0.450.006–0.018 | 0.6–0.720.024–0.028 | — | — | — | Faster prints and stronger parts with little loss of detail; good for PETG and functional parts |
| 0.8 mm | 0.80.031 | 0.2–0.60.008–0.024 | 0.8–0.960.031–0.038 | — | — | — | Large parts, vases and drafts; needs a high-flow hotend (Volcano or similar) to reach full speed |
| 1.0 mm | 10.039 | 0.25–0.750.01–0.03 | 1–1.20.039–0.047 | — | — | — | Large parts, vases and drafts; needs a high-flow hotend (Volcano or similar) to reach full speed |
| 1.2 mm | 1.20.047 | 0.3–0.90.012–0.035 | 1.2–1.440.047–0.057 | — | — | — | Large parts, vases and drafts; needs a high-flow hotend (Volcano or similar) to reach full speed |
| Nozzle types (thread and size) | |||||||
| E3D V6 type | — | — | — | M6 × 1 | 7 | 12.50.492 | E3D V6 and most Prusa printers; short nozzle with a long thread |
| Volcano type | — | — | — | M6 × 1 | 7 | 210.827 | E3D Volcano and similar long melt-zone heater blocks for high flow |
| MK8 type | — | — | — | M6 × 1 | 6 | — | Creality Ender and CR series and many other budget printers |
No exact match. The nearest sizes:
Choosing layer height and line width
Layer height above about 75 % of the nozzle diameter gives poor layer bonding, because the bead is no longer pressed onto the layer below. Below about 25 % the slicer struggles to meter such a small flow and prints get slow. Within the range, thinner layers mean smoother curved surfaces and longer print times.
Line (extrusion) width is normally 100–120 % of the nozzle diameter; slicers use about 0.42–0.45 mm for a 0.4 mm nozzle. Wider lines (up to about 150 %) give stronger walls; narrower than the nozzle is unreliable.
Flow limit: a larger nozzle only prints faster if the hotend can melt enough plastic. A standard V6-type hotend tops out around 10–15 mm³/s with PLA; 0.8 mm and larger nozzles are best used with a long melt zone such as a Volcano.
About 3D Printer Nozzle Sizes
Nozzle diameter is stamped on the hex (0.4, 0.6) or shown by a colour code on some brands. Brass nozzles are standard; hardened steel, ruby-tipped or tungsten-carbide nozzles are needed for abrasive filaments (carbon fibre, glass fibre, glow-in-the-dark), and hardened steel conducts heat less well, so print 5–10 °C hotter.
V6 and MK8 nozzles share the M6 × 1 thread but not the geometry: the V6 nozzle has a longer thread and shorter overall length; an MK8 nozzle in a V6 block (or the reverse) leaves a gap or bottoms out and leaks. Volcano nozzles are about 21 mm long against 12.5 mm for V6. Many newer printers use proprietary quick-swap nozzles that fit only their own hotend.
Change nozzles hot (about 250–285 °C, per the hotend maker), holding the heater block with a wrench so the heat break is not twisted, and tighten to the torque the hotend maker specifies.
Questions
What layer height for a 0.4 mm nozzle?
0.1–0.3 mm; 0.2 mm is the usual default. 0.08–0.1 mm is possible for fine detail but slow.
What layer height for a 0.6 mm nozzle?
About 0.15–0.45 mm; 0.3 mm is a common default.
What thread is a 3D printer nozzle?
E3D V6, Volcano and MK8 nozzles are all M6 × 1 (6 mm, 1 mm pitch). They differ in length, so use the type made for your heater block.
What size wrench for a 3D printer nozzle?
7 mm for E3D V6 and Volcano nozzles, 6 mm for MK8 (Creality) nozzles. Some clone nozzles differ; check before buying a socket.
Is a 0.6 mm nozzle better than 0.4 mm?
For functional parts it prints faster and stronger with slightly less fine detail. For small text and miniatures, 0.4 mm or smaller is better.
Sources
- Prusa Knowledge Base: Layer height and nozzle diameter (25–75 % rule, 0.45 mm default width for 0.4 mm)
- E3D: V6 and Volcano nozzle specifications (M6 × 1 thread)
- Filament2Print: Compatibility of E3D nozzles (V6, Volcano, MK8; wrench sizes)
- Bondtech: Volcano-type CHT nozzle datasheet (21 mm total length)
- Anton Mansson: How to identify 3D printer nozzle type
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.