Drill Size Chart: Number, Letter, Fraction and Metric

Every number, letter and fractional drill with its decimal inch and millimetre size, the nearest drill in the other systems and the thread it is used to tap. Number drills get smaller as the number rises (#1 = 0.228″, #80 = 0.0135″); letter drills continue upward from A = 0.234″ to Z = 0.413″.

174 sizesChecked 2026-11-154 sources
024681012mmNumber#80#1LetterAZFraction1/64″1/2″Metric11300.10.20.30.40.5inch
Each tick is one drill size. Number drills cover the fine steps up to 0.228″, letter drills continue to 0.413″.Drawn to scale · Dimensions in mmDimensions in inches

Size chartTap a size for its drawing and full specs

174 of 174
Drill⌀Diametermminmm · inNearest fractional drillNearest 0.1 mm metric drillNearest number / letter drillTap drill for
Number (wire gauge) drills #1–#80
#15.7910.228015/64″ (.2344″)5.8 mm (.2283″)——
#25.6130.22107/32″ (.2188″)5.6 mm (.2205″)——
#35.4100.21307/32″ (.2188″)5.4 mm (.2126″)—1/4-28 UNF
#45.3090.209013/64″ (.2031″)5.3 mm (.2087″)——
#55.2200.205513/64″ (.2031″)5.2 mm (.2047″)——
#65.1820.204013/64″ (.2031″)5.2 mm (.2047″)——
#75.1050.201013/64″ (.2031″)5.1 mm (.2008″)—1/4-20 UNC
#85.0550.199013/64″ (.2031″)5.1 mm (.2008″)——
#94.9780.196013/64″ (.2031″)5.0 mm (.1969″)——
#104.9150.19353/16″ (.1875″)4.9 mm (.1929″)——
#114.8510.19103/16″ (.1875″)4.9 mm (.1929″)——
#124.8010.18903/16″ (.1875″)4.8 mm (.1890″)——
#134.6990.18503/16″ (.1875″)4.7 mm (.1850″)——
#144.6230.18203/16″ (.1875″)4.6 mm (.1811″)—#12-28 UNF
#154.5720.18003/16″ (.1875″)4.6 mm (.1811″)——
#164.4960.177011/64″ (.1719″)4.5 mm (.1772″)—#12-24 UNC
#174.3940.173011/64″ (.1719″)4.4 mm (.1732″)——
#184.3050.169511/64″ (.1719″)4.3 mm (.1693″)——
#194.2160.166011/64″ (.1719″)4.2 mm (.1654″)——
#204.0890.16105/32″ (.1563″)4.1 mm (.1614″)——
#214.0390.15905/32″ (.1563″)4.0 mm (.1575″)—#10-32 UNF
#223.9880.15705/32″ (.1563″)4.0 mm (.1575″)——
#233.9120.15405/32″ (.1563″)3.9 mm (.1535″)——
#243.8610.15205/32″ (.1563″)3.9 mm (.1535″)——
#253.7970.14955/32″ (.1563″)3.8 mm (.1496″)—#10-24 UNC
#263.7340.14709/64″ (.1406″)3.7 mm (.1457″)——
#273.6580.14409/64″ (.1406″)3.7 mm (.1457″)——
#283.5690.14059/64″ (.1406″)3.6 mm (.1417″)——
#293.4540.13609/64″ (.1406″)3.5 mm (.1378″)—#8-32 UNC, #8-36 UNF
#303.2640.12851/8″ (.1250″)3.3 mm (.1299″)——
#313.0480.12001/8″ (.1250″)3.0 mm (.1181″)——
#322.9460.11607/64″ (.1094″)2.9 mm (.1142″)——
#332.8700.11307/64″ (.1094″)2.9 mm (.1142″)—#6-40 UNF
#342.8190.11107/64″ (.1094″)2.8 mm (.1102″)——
#352.7940.11007/64″ (.1094″)2.8 mm (.1102″)——
#362.7050.10657/64″ (.1094″)2.7 mm (.1063″)—#6-32 UNC
#372.6420.10407/64″ (.1094″)2.6 mm (.1024″)—#5-44 UNF
#382.5780.10153/32″ (.0938″)2.6 mm (.1024″)—#5-40 UNC
#392.5270.09953/32″ (.0938″)2.5 mm (.0984″)——
#402.4890.09803/32″ (.0938″)2.5 mm (.0984″)——
#412.4380.09603/32″ (.0938″)2.4 mm (.0945″)——
#422.3750.09353/32″ (.0938″)2.4 mm (.0945″)—#4-48 UNF
#432.2610.08903/32″ (.0938″)2.3 mm (.0906″)—#4-40 UNC
#442.1840.08603/32″ (.0938″)2.2 mm (.0866″)——
#452.0830.08205/64″ (.0781″)2.1 mm (.0827″)—#3-56 UNF
#462.0570.08105/64″ (.0781″)2.1 mm (.0827″)——
#471.9940.07855/64″ (.0781″)2.0 mm (.0787″)—#3-48 UNC
#481.9300.07605/64″ (.0781″)1.9 mm (.0748″)——
#491.8540.07305/64″ (.0781″)1.9 mm (.0748″)——
#501.7780.07001/16″ (.0625″)1.8 mm (.0709″)—#2-56 UNC, #2-64 UNF
#511.7020.06701/16″ (.0625″)1.7 mm (.0669″)——
#521.6130.06351/16″ (.0625″)1.6 mm (.0630″)——
#531.5110.05951/16″ (.0625″)1.5 mm (.0591″)—#1-64 UNC, #1-72 UNF
#541.3970.05501/16″ (.0625″)1.4 mm (.0551″)——
#551.3210.05203/64″ (.0469″)1.3 mm (.0512″)——
#561.1810.04653/64″ (.0469″)1.2 mm (.0472″)——
#571.0920.04303/64″ (.0469″)1.1 mm (.0433″)——
#581.0670.04203/64″ (.0469″)1.1 mm (.0433″)——
#591.0410.04103/64″ (.0469″)1.0 mm (.0394″)——
#601.0160.04003/64″ (.0469″)1.0 mm (.0394″)——
#610.9910.03901/32″ (.0313″)1.0 mm (.0394″)——
#620.9650.03801/32″ (.0313″)1.0 mm (.0394″)——
#630.9400.03701/32″ (.0313″)0.9 mm (.0354″)——
#640.9140.03601/32″ (.0313″)0.9 mm (.0354″)——
#650.8890.03501/32″ (.0313″)0.9 mm (.0354″)——
#660.8380.03301/32″ (.0313″)0.8 mm (.0315″)——
#670.8130.03201/32″ (.0313″)0.8 mm (.0315″)——
#680.7870.03101/32″ (.0313″)0.8 mm (.0315″)——
#690.7420.02921/32″ (.0313″)0.7 mm (.0276″)——
#700.7110.02801/32″ (.0313″)0.7 mm (.0276″)——
#710.6600.02601/32″ (.0313″)0.7 mm (.0276″)——
#720.6350.02501/32″ (.0313″)0.6 mm (.0236″)——
#730.6100.02401/32″ (.0313″)0.6 mm (.0236″)——
#740.5710.02251/64″ (.0156″)0.6 mm (.0236″)——
#750.5330.02101/64″ (.0156″)0.5 mm (.0197″)——
#760.5080.02001/64″ (.0156″)0.5 mm (.0197″)——
#770.4570.01801/64″ (.0156″)0.5 mm (.0197″)——
#780.4060.01601/64″ (.0156″)0.4 mm (.0157″)——
#790.3680.01451/64″ (.0156″)0.4 mm (.0157″)——
#800.3430.01351/64″ (.0156″)0.3 mm (.0118″)——
Letter drills A–Z
Letter A5.9440.234015/64″ (.2344″)5.9 mm (.2323″)——
Letter B6.0450.238015/64″ (.2344″)6.0 mm (.2362″)——
Letter C6.1470.242015/64″ (.2344″)6.1 mm (.2402″)——
Letter D6.2480.24601/4″ (.2500″)6.2 mm (.2441″)——
Letter E6.3500.25001/4″ (.2500″)6.4 mm (.2520″)——
Letter F6.5280.25701/4″ (.2500″)6.5 mm (.2559″)—5/16-18 UNC
Letter G6.6290.261017/64″ (.2656″)6.6 mm (.2598″)——
Letter H6.7560.266017/64″ (.2656″)6.8 mm (.2677″)——
Letter I6.9090.272017/64″ (.2656″)6.9 mm (.2717″)—5/16-24 UNF
Letter J7.0360.27709/32″ (.2813″)7.0 mm (.2756″)——
Letter K7.1370.28109/32″ (.2813″)7.1 mm (.2795″)——
Letter L7.3660.290019/64″ (.2969″)7.4 mm (.2913″)——
Letter M7.4930.295019/64″ (.2969″)7.5 mm (.2953″)——
Letter N7.6710.302019/64″ (.2969″)7.7 mm (.3031″)——
Letter O8.0260.31605/16″ (.3125″)8.0 mm (.3150″)——
Letter P8.2040.323021/64″ (.3281″)8.2 mm (.3228″)——
Letter Q8.4330.332021/64″ (.3281″)8.4 mm (.3307″)—3/8-24 UNF
Letter R8.6110.339011/32″ (.3438″)8.6 mm (.3386″)——
Letter S8.8390.348011/32″ (.3438″)8.8 mm (.3465″)——
Letter T9.0930.358023/64″ (.3594″)9.1 mm (.3583″)——
Letter U9.3470.36803/8″ (.3750″)9.3 mm (.3661″)—7/16-14 UNC
Letter V9.5760.37703/8″ (.3750″)9.6 mm (.3780″)——
Letter W9.8040.386025/64″ (.3906″)9.8 mm (.3858″)——
Letter X10.0840.397025/64″ (.3906″)10.1 mm (.3976″)——
Letter Y10.2620.404013/32″ (.4063″)10.3 mm (.4055″)——
Letter Z10.4900.413013/32″ (.4063″)10.5 mm (.4134″)——
Fractional drills 1/64″–1/2″
1/64″0.3970.0156—0.4 mm (.0157″)#78 (.0160″)—
1/32″0.7940.0313—0.8 mm (.0315″)#68 (.0310″)—
3/64″1.1910.0469—1.2 mm (.0472″)#56 (.0465″)#0-80 UNF
1/16″1.5880.0625—1.6 mm (.0630″)#52 (.0635″)—
5/64″1.9840.0781—2.0 mm (.0787″)#47 (.0785″)—
3/32″2.3810.0938—2.4 mm (.0945″)#42 (.0935″)—
7/64″2.7780.1094—2.8 mm (.1102″)#35 (.1100″)—
1/8″3.1750.1250—3.2 mm (.1260″)#30 (.1285″)—
9/64″3.5720.1406—3.6 mm (.1417″)#28 (.1405″)—
5/32″3.9690.1563—4.0 mm (.1575″)#22 (.1570″)—
11/64″4.3660.1719—4.4 mm (.1732″)#17 (.1730″)—
3/16″4.7620.1875—4.8 mm (.1890″)#12 (.1890″)—
13/64″5.1590.2031—5.2 mm (.2047″)#6 (.2040″)—
7/32″5.5560.2188—5.6 mm (.2205″)#2 (.2210″)—
15/64″5.9530.2344—6.0 mm (.2362″)A (.2340″)—
1/4″6.3500.2500—6.4 mm (.2520″)E (.2500″)—
17/64″6.7470.2656—6.7 mm (.2638″)H (.2660″)—
9/32″7.1440.2813—7.1 mm (.2795″)K (.2810″)—
19/64″7.5410.2969—7.5 mm (.2953″)M (.2950″)—
5/16″7.9380.3125—7.9 mm (.3110″)O (.3160″)3/8-16 UNC
21/64″8.3340.3281—8.3 mm (.3268″)Q (.3320″)—
11/32″8.7310.3438—8.7 mm (.3425″)S (.3480″)—
23/64″9.1280.3594—9.1 mm (.3583″)T (.3580″)—
3/8″9.5250.3750—9.5 mm (.3740″)V (.3770″)—
25/64″9.9220.3906—9.9 mm (.3898″)W (.3860″)7/16-20 UNF
13/32″10.3190.4063—10.3 mm (.4055″)Y (.4040″)—
27/64″10.7160.4219—10.7 mm (.4213″)—1/2-13 UNC
7/16″11.1120.4375—11.1 mm (.4370″)——
29/64″11.5090.4531—11.5 mm (.4528″)—1/2-20 UNF
15/32″11.9060.4688—11.9 mm (.4685″)——
31/64″12.3030.4844—12.3 mm (.4843″)——
1/2″12.7000.5000—12.7 mm (.5000″)——
Common metric drills
1 mm1.0000.03943/64″ (.0469″)—#61 (.0390″)—
1.1 mm1.1000.04333/64″ (.0469″)—#57 (.0430″)M1.4
1.25 mm1.2500.04923/64″ (.0469″)—#56 (.0465″)M1.6
1.5 mm1.5000.05911/16″ (.0625″)—#53 (.0595″)—
1.6 mm1.6000.06301/16″ (.0625″)—#52 (.0635″)M2
2 mm2.0000.07875/64″ (.0781″)—#47 (.0785″)—
2.05 mm2.0500.08075/64″ (.0781″)—#46 (.0810″)M2.5
2.5 mm2.5000.09843/32″ (.0938″)—#40 (.0980″)M3
2.9 mm2.9000.11427/64″ (.1094″)—#33 (.1130″)M3.5
3 mm3.0000.11811/8″ (.1250″)—#31 (.1200″)—
3.3 mm3.3000.12991/8″ (.1250″)—#30 (.1285″)M4
3.5 mm3.5000.13789/64″ (.1406″)—#29 (.1360″)M4×0.5
4 mm4.0000.15755/32″ (.1563″)—#22 (.1570″)—
4.2 mm4.2000.165411/64″ (.1719″)—#19 (.1660″)M5
4.5 mm4.5000.177211/64″ (.1719″)—#16 (.1770″)M5×0.5
5 mm5.0000.196913/64″ (.2031″)—#9 (.1960″)M6
5.1 mm5.1000.200813/64″ (.2031″)—#7 (.2010″)—
5.5 mm5.5000.21657/32″ (.2188″)—#3 (.2130″)—
6 mm6.0000.236215/64″ (.2344″)—B (.2380″)M7
6.5 mm6.5000.25591/4″ (.2500″)—F (.2570″)—
6.8 mm6.8000.267717/64″ (.2656″)—H (.2660″)M8
7 mm7.0000.27569/32″ (.2813″)—J (.2770″)M8×1
7.5 mm7.5000.295319/64″ (.2969″)—M (.2950″)—
8 mm8.0000.31505/16″ (.3125″)—O (.3160″)—
8.5 mm8.5000.334621/64″ (.3281″)—Q (.3320″)M10
8.75 mm8.7500.344511/32″ (.3438″)—S (.3480″)M10×1.25
9 mm9.0000.354323/64″ (.3594″)—T (.3580″)M10×1
9.5 mm9.5000.37403/8″ (.3750″)—V (.3770″)—
10 mm10.0000.393725/64″ (.3906″)—X (.3970″)—
10.2 mm10.2000.401613/32″ (.4063″)—Y (.4040″)M12
10.5 mm10.5000.413413/32″ (.4063″)—Z (.4130″)M12×1.5
11 mm11.0000.43317/16″ (.4375″)———
11.5 mm11.5000.452829/64″ (.4531″)———
12 mm12.0000.472415/32″ (.4688″)——M14
12.5 mm12.5000.492131/64″ (.4844″)——M14×1.5
13 mm13.0000.511833/64″ (.5156″)———

How the drill size systems fit together

US shops use four overlapping series. Fractional drills step by 1/64″ (0.0156″). Number drills (#1–#80, from the old wire gauge) fill the gaps below 1/4″ in much finer steps, and letter drills (A–Z) fill the gaps between 15/64″ and 13/32″. Metric drills step by 0.1 mm (0.0039″) in jobber sets, with half sizes such as 6.75 or 8.75 mm made for tapping.

The series meet without a gap: #1 is 0.228″, letter A is 0.234″. A few sizes coincide or nearly so: letter E is exactly 1/4″, #28 (0.1405″) is within 0.0001″ of 9/64″, #12 (0.189″) is within 0.0015″ of 3/16″, letter H (0.266″) is 6.76 mm, practically a 6.75 mm tap drill.

To identify an unmarked drill, measure across the margins (the two narrow lands at the outer edge of the flutes) with a micrometer or caliper, not across the flutes or the shank of a reduced-shank bit. Then look up the nearest size in the chart.

About Drill Sizes

Number and letter drills exist mainly for tap drills and close clearance holes in inch work: the standard 75 % tap drill for most UNC and UNF threads below 1/2″ is a number or letter size (#7 for 1/4-20, F for 5/16-18, U for 7/16-14). If you only own fractional drills, the nearest fractional size is usually within 0.002–0.006″. That is fine for clearance holes, but it changes the thread percentage when tapping.

The decimal sizes come from ASME B94.11M and the long-standing ANSI tables used by every US drill maker; millimetre values are exact conversions (1″ = 25.4 mm). The nearest-equivalent columns are calculated, so a fractional drill shows the closest 1/64″ and the closest 0.1 mm metric size, with their own decimal values for comparison.

Metric drills are listed for the sizes most used in practice: 0.5 mm steps plus the ISO coarse tap drills (2.5, 3.3, 4.2, 5, 6.8, 8.5, 10.2 mm) and common fine-thread tap drills. Any 0.1 mm size up to 13 mm is a standard jobber drill.

Drill tolerance and hole size

A twist drill is ground to its nominal size within a few ten-thousandths of an inch (h8 tolerance for metric drills), but the hole it makes is usually 0.001–0.004″ oversize, more with a worn or badly sharpened point, less in soft plastics that close up. For a precise hole, drill slightly undersize and ream.

Very small number drills

Sizes #61–#80 (0.039″ down to 0.0135″) are used for PCB vias, jewelry, model making and carburetor jets. They are fragile: use a drill press or pin vise, high spindle speed and frequent pecking.

Questions

What size is a #7 drill bit?

0.201″ = 5.105 mm, slightly smaller than 13/64″ (0.2031″). It is the standard tap drill for 1/4-20 UNC.

What size is a letter F drill?

0.257″ = 6.528 mm, slightly larger than 1/4″. It is the tap drill for 5/16-18 UNC and a close-fit clearance hole for 1/4″ bolts.

Which is bigger, a #1 or a #60 drill?

#1. Number drills shrink as the number grows: #1 is 0.228″ (5.79 mm), #60 is 0.040″ (1.02 mm) and #80 is 0.0135″ (0.343 mm).

What size is a #29 drill in mm?

0.136″ = 3.454 mm. It is the tap drill for #8-32. The nearest metric drill is 3.5 mm.

What size is a letter Q drill?

0.332″ = 8.433 mm, the tap drill for 3/8-24 UNF. The closest fractional drill is 21/64″ (0.3281″).

Can I use a fractional drill instead of a number or letter drill?

For clearance holes, usually yes: pick the nearest size that is not smaller. For tapping, check the difference: 13/64″ for 1/4-20 (vs #7) is fine, but a hole 0.005″ too small in a small thread makes the tap bind and break.

Sources

  1. ASME B94.11M: Twist drills (number, letter, fractional and metric sizes)
  2. Starrett: Decimal equivalents and tap drill sizes chart
  3. Machinery's Handbook, 31st ed.: Twist drill sizes and tap drill tables
  4. ISO 235: Parallel shank jobber and stub series drills (metric diameters)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.