3D Printer Filament Sizes and Temperatures

FFF/FDM printers take filament of 1.75 mm (most printers today) or 2.85 mm (Ultimaker, older Lulzbot and RepRap machines, often sold as '3 mm'). A 1 kg spool of 1.75 mm PLA holds about 335 m; the same weight of 2.85 mm holds only about 126 m.

16 diameters and materialsChecked 2026-11-155 sources
Typical ranges; the spool label wins. Tap a material for details.Drawn to scale

Filament chartTap a diameter or material for details

16 of 16
FilamentdDiametermminNozzle temperature (typical)°C°FBed temperature (typical)°C°FTgGlass transition (approx.)°C°FρDensity (typical)g/cm³lb/in³Length per kgmft
Diameters · length per kg of PLA
1.75 mm1.750.0689————3351099
2.85 mm2.850.1122————126413
3.00 mm3.000.1181————114374
Materials · length per kg at 1.75 mm
PLA—190–220374–42850–60122–140601401.240.04483351099
PETG—230–250446–48270–90158–194801761.270.04593271073
ABS—230–260446–50095–110203–2301052211.040.03764001312
ASA—240–260464–50090–110194–2301002121.070.03873891276
TPU 95A—210–240410–46430–6086–140—1.210.04373441129
Nylon PA6—250–280482–53670–100158–212—1.140.04123651198
Nylon PA12—245–275473–52780–110176–230—1.010.03654121352
PC—260–310500–590100–120212–2481472971.200.04343461135
HIPS—220–250428–48290–110194–2301002121.040.03764001312
PVA—185–210365–41045–60113–140—1.230.04443381109
PLA-CF—200–230392–44650–60122–14060140——
PETG-CF—240–260464–50070–90158–19480176——
PEEK—370–420698–788120–160248–3201432891.300.04703201050

How to choose diameter and settings

Diameter is fixed by the printer, not by preference: the extruder gears and the hotend bore are made for one size. Check the printer's spec sheet. 1.75 mm is standard on Prusa, Bambu Lab, Creality, Anycubic, Voron and most other current machines; 2.85 mm on Ultimaker and some older printers. 2.85 mm and '3 mm' filament are interchangeable in practice; measure your filament and enter the real value in the slicer.

Measure with a caliper at several points along a metre of filament and across two directions. Good filament stays within ±0.02 mm of nominal and is round; cheap filament can drift ±0.05 mm or more, which shows up as uneven extrusion. A 0.05 mm error on 1.75 mm filament is a 6 % error in extruded volume.

Temperatures in the chart are typical ranges. Start in the middle of the range printed on the spool, then adjust: hotter for stronger layer bonding and faster printing, cooler for less stringing and sharper overhangs. Bed temperatures assume a PEI or textured sheet; first layers often run 5 °C hotter.

Tg (glass transition) is roughly where a printed part starts to soften. PLA parts deform in a hot car (around 60 °C); PETG lasts to about 80 °C, ABS and ASA to about 100 °C, PC to about 145 °C.

About 3D Printer Filament

A filament's weight, length and diameter are tied together by its density. Length per kilogram is 1000 g divided by (density × cross-section). Because the cross-section grows with the square of the diameter, 2.85 mm filament has 2.65 times the area of 1.75 mm, so a kilogram is 2.65 times shorter. Dense materials are shorter per kilogram too: 1 kg of 1.75 mm PLA (1.24 g/cm³) is about 335 m, 1 kg of ABS (1.04 g/cm³) about 400 m.

Slicers estimate filament use from the extruded length; multiply by the weight per metre to get grams. The calculator converts both ways for any material and diameter.

The values here are generic. Blends and brands differ: 'PLA+', silk PLA, high-speed PLA, glass- and carbon-filled grades all shift temperatures and density. The spool label and the manufacturer's data sheet take precedence.

Materials in one paragraph each

PLA: easiest to print, stiff, little warping, low heat resistance. PETG: tougher and more heat-resistant than PLA, prints without an enclosure, strings more. ABS and ASA: heat resistant to about 100 °C, need an enclosure to stop warping and to contain fumes; ASA is UV-stable for outdoor parts. TPU 95A: flexible, rubber-like; print slowly with a direct-drive extruder. Nylon (PA6, PA12): tough and wear-resistant, absorbs moisture fast; dry before use. PC: strong and heat-resistant, needs high temperatures and an enclosure. HIPS: ABS-like, dissolves in limonene, used as support for ABS. PVA: water-soluble support for PLA. PLA-CF / PETG-CF: stiffer, matte, abrasive to brass nozzles. PEEK: engineering material for industrial printers with heated chambers.

Keep filament dry

Most filaments absorb water from the air. Wet filament pops and hisses in the nozzle, strings, and prints weak, rough parts. Nylon, TPU, PVA and PC are the most sensitive, PETG moderately, PLA least. Store spools sealed with desiccant and dry them in a filament dryer before printing: typically 45–55 °C for PLA and TPU, 60–70 °C for PETG, 70–80 °C for nylon and PC, for several hours (follow the manufacturer's values).

Questions

How many meters are on a 1 kg spool of 1.75 mm filament?

About 335 m of PLA (1.24 g/cm³), 330 m of PETG (1.27 g/cm³) and 400 m of ABS (1.04 g/cm³). The spool's own weight is not included.

Can I use 1.75 mm filament in a 2.85 mm printer?

No. The thin filament buckles inside the larger hotend bore and the extruder cannot feed it reliably. Use the diameter the printer was built for, or convert the extruder and hotend.

Is 2.85 mm the same as 3 mm filament?

In practice, yes. Almost all filament sold as '3 mm' is 2.85 mm nominal. Measure it and set the real diameter in the slicer.

What temperature should I print PLA at?

Typically 190–220 °C nozzle and 50–60 °C bed. Start at about 210 °C and adjust in 5 °C steps; follow the range on the spool.

Which filaments need an enclosure?

ABS, ASA, nylon and polycarbonate warp without one, and ABS/ASA release fumes that should be ventilated. HIPS benefits from one. PLA, PETG and TPU print fine in the open, and PLA actually prefers it.

Sources

  1. Prusa Knowledge Base: Material guide (PLA, PETG, ASA, PC, Polyamide pages)
  2. Prusament technical data sheets (diameter tolerance ±0.02 mm, densities)
  3. Ultimaker: material technical data sheets (2.85 mm filaments)
  4. Simplify3D: Filament properties table
  5. Victrex: PEEK 450G datasheet (Tg 143 °C, density 1.30 g/cm³)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.