Metric Thread Size Chart
ISO metric screw threads from M1 to M64 with coarse and fine pitches, tap drills, basic diameters and clearance holes. The tap drill for a coarse thread is simply major diameter minus pitch: M8 × 1.25 → 6.8 mm, M10 × 1.5 → 8.5 mm.
Size chartTap a size for its drawing and full specs
| Thread | PCoarse pitchmmTPI | Tap drill, coarsemmin | Fine pitch (common)mmTPI | Tap drill, finemmin | Clearance hole, finemmin | Clearance hole, mediummmin | Clearance hole, coarsemmin |
|---|---|---|---|---|---|---|---|
| M1 | 0.25101.6 | 0.750.030 | 0.2127.0 | 0.80.031 | 1.10.043 | 1.20.047 | 1.30.051 |
| M1.2 | 0.25101.6 | 0.950.037 | 0.2127.0 | 10.039 | 1.30.051 | 1.40.055 | 1.50.059 |
| M1.4 | 0.384.7 | 1.10.043 | 0.2127.0 | 1.20.047 | 1.50.059 | 1.60.063 | 1.80.071 |
| M1.6 | 0.3572.6 | 1.250.049 | 0.2127.0 | 1.40.055 | 1.70.067 | 1.80.071 | 20.079 |
| M2 | 0.463.5 | 1.60.063 | 0.25101.6 | 1.750.069 | 2.20.087 | 2.40.094 | 2.60.102 |
| M2.5 | 0.4556.4 | 2.050.081 | 0.3572.6 | 2.150.085 | 2.70.106 | 2.90.114 | 3.10.122 |
| M3 | 0.550.8 | 2.50.098 | 0.3572.6 | 2.650.104 | 3.20.126 | 3.40.134 | 3.60.142 |
| M3.5 | 0.642.3 | 2.90.114 | 0.3572.6 | 3.150.124 | 3.70.146 | 3.90.154 | 4.20.165 |
| M4 | 0.736.3 | 3.30.130 | 0.550.8 | 3.50.138 | 4.30.169 | 4.50.177 | 4.80.189 |
| M5 | 0.831.7 | 4.20.165 | 0.550.8 | 4.50.177 | 5.30.209 | 5.50.217 | 5.80.228 |
| M6 | 125.4 | 50.197 | 0.7533.9 | 5.250.207 | 6.40.252 | 6.60.260 | 70.276 |
| M7 | 125.4 | 60.236 | 0.7533.9 | 6.250.246 | 7.40.291 | 7.60.299 | 80.315 |
| M8 | 1.2520.3 | 6.80.268 | 125.4 | 70.276 | 8.40.331 | 90.354 | 100.394 |
| M10 | 1.516.9 | 8.50.335 | 1.2520.3 | 8.750.344 | 10.50.413 | 110.433 | 120.472 |
| M12 | 1.7514.5 | 10.20.402 | 1.516.9 | 10.50.413 | 130.512 | 13.50.531 | 14.50.571 |
| M14 | 212.7 | 120.472 | 1.516.9 | 12.50.492 | 150.591 | 15.50.610 | 16.50.650 |
| M16 | 212.7 | 140.551 | 1.516.9 | 14.50.571 | 170.669 | 17.50.689 | 18.50.728 |
| M18 | 2.510.2 | 15.50.610 | 1.516.9 | 16.50.650 | 190.748 | 200.787 | 210.827 |
| M20 | 2.510.2 | 17.50.689 | 1.516.9 | 18.50.728 | 210.827 | 220.866 | 240.945 |
| M22 | 2.510.2 | 19.50.768 | 1.516.9 | 20.50.807 | 230.906 | 240.945 | 261.024 |
| M24 | 38.5 | 210.827 | 212.7 | 220.866 | 250.984 | 261.024 | 281.102 |
| M27 | 38.5 | 240.945 | 212.7 | 250.984 | 281.102 | 301.181 | 321.260 |
| M30 | 3.57.3 | 26.51.043 | 212.7 | 281.102 | 311.220 | 331.299 | 351.378 |
| M33 | 3.57.3 | 29.51.161 | 212.7 | 311.220 | 341.339 | 361.417 | 381.496 |
| M36 | 46.4 | 321.260 | 38.5 | 331.299 | 371.457 | 391.535 | 421.654 |
| M39 | 46.4 | 351.378 | 38.5 | 361.417 | 401.575 | 421.654 | 451.772 |
| M42 | 4.55.6 | 37.51.476 | 38.5 | 391.535 | 431.693 | 451.772 | 481.890 |
| M45 | 4.55.6 | 40.51.594 | 38.5 | 421.654 | 461.811 | 481.890 | 522.047 |
| M48 | 55.1 | 431.693 | 38.5 | 451.772 | 501.969 | 522.047 | 562.205 |
| M52 | 55.1 | 471.850 | 46.4 | 481.890 | 542.126 | 562.205 | 622.441 |
| M56 | 5.54.6 | 50.51.988 | 46.4 | 522.047 | 582.283 | 622.441 | 662.598 |
| M60 | 5.54.6 | 54.52.146 | 46.4 | 562.205 | 622.441 | 662.598 | 702.756 |
| M64 | 64.2 | 582.283 | 46.4 | 602.362 | 662.598 | 702.756 | 742.913 |
No exact match. The nearest sizes:
How to read a metric thread designation
A metric thread is written M + major diameter in millimetres, then × pitch: M8 × 1.25. When the pitch is left out, the coarse pitch is meant, so plain M8 is M8 × 1.25. A fine thread always carries its pitch: M8 × 1, M12 × 1.5. Left-hand threads add LH (M12 × 1.5 LH).
A tolerance class may follow: M8 × 1.25-6g for a bolt, -6H for a nut. Lower-case letters are external threads, capitals internal; 6g/6H is the normal medium fit and is what you get when nothing is specified.
To identify an unknown thread, measure the outside diameter of the bolt with a caliper. It reads a little under nominal (an M8 bolt measures about 7.8–7.97 mm). Then measure the pitch with a thread gauge, or measure across 10 crests and divide by 10. If the pitch matches the coarse column, it is a standard metric bolt; if it is finer, check the fine pitches of that size. A diameter near 6.35, 7.94 or 9.53 mm points to an inch thread instead; see unified threads.
About Metric Threads
All metric threads here use the same symmetric 60° profile defined in ISO 68-1. ISO 261 lists which diameter–pitch combinations exist; ISO 262 narrows them to the sizes used for ordinary bolts, screws and nuts; ISO 724 gives the basic pitch and minor diameters, which the chart computes from the standard formulas (d₂ = d − 0.6495 P, D₁ = d − 1.0825 P, d₃ = d − 1.2269 P).
Every size has exactly one coarse pitch, and that is the thread of almost every off-the-shelf bolt, nut and tapped hole. Fine pitches exist for most sizes from M8 up and are used where the thread must be stronger in thin walls, adjust finely or resist loosening: automotive wheel studs (M12 × 1.5, M14 × 1.5), hydraulic fittings, spark plugs (M14 × 1.25), lens and optical mounts.
The tap drill column uses the workshop rule drill = d − P, which gives about 75–80 % thread engagement and matches the DIN 336 tap drill table. In stainless steel or other tough material some shops drill 0.1 mm larger to save taps; for thread-forming (roll) taps the hole is larger again (about d − P/2) and must be taken from the tap maker's table.
Clearance holes follow ISO 273. The medium series is the normal choice for bolted joints. Fine holes position parts more accurately but leave little room for hole-position error; coarse holes suit castings, welded parts and anything aligned by hand.
First, second and third choice sizes
ISO 261 ranks diameters: first choice (M3, M4, M5, M6, M8, M10, M12, M16, M20, M24, M30 …) should be used whenever possible; second choice (M3.5, M14, M18, M22, M27, M33 …) only when necessary; third choice sizes such as M7 are best avoided because bolts, nuts and taps are hard to find.
Minor diameter of the bolt and of the nut
The bolt's root (d₃) is a little smaller than the nut's minor diameter (D₁) because the external thread has a rounded root. D₁ is the smallest hole a tapped thread can have; the tap drill is slightly larger than D₁, which is why a d − P hole never gives a full 100 % thread. The stress area used for bolt strength sits between d₂ and d₃.
Metric vs. inch threads that look alike
Several pairs are close enough to start but will strip or cross-thread: M6 × 1 vs 1/4″-20, M8 × 1.25 vs 5/16″-18, M10 × 1.5 vs 3/8″-16, M5 × 0.8 vs #10-24. Measure the pitch: 20 TPI is 1.27 mm, not 1.0 mm.
Questions
What size drill do I use for an M8 tap?
6.8 mm for the standard coarse M8 × 1.25 thread (8 − 1.25 = 6.75, rounded to the next stock drill). For fine M8 × 1, use 7.0 mm. The nearest inch drill to 6.8 mm is letter H (0.266″ = 6.76 mm).
How do I calculate the tap drill size for a metric thread?
Subtract the pitch from the major diameter: M6 × 1 → 5.0 mm, M10 × 1.5 → 8.5 mm, M12 × 1.75 → 10.25 mm (use 10.2 mm). This gives roughly 75–80 % thread depth, which is the normal choice for cutting taps.
What is the difference between coarse and fine metric threads?
Same diameter, different pitch. M10 coarse has 1.5 mm between crests, M10 fine has 1.25 or 1 mm. Coarse threads assemble faster and tolerate dirt and damage; fine threads are slightly stronger in tension, allow finer adjustment and are less likely to loosen. If a drawing just says M10, it means coarse.
What size clearance hole for an M6 bolt?
6.6 mm for the normal (ISO 273 medium) fit. Use 6.4 mm for a close fit or 7 mm for a loose fit. For M8 the values are 8.4 / 9 / 10 mm, for M10 10.5 / 11 / 12 mm.
Is M6 the same as 1/4 inch?
No. M6 is 6.0 mm with a 1 mm pitch; 1/4″-20 is 6.35 mm with 20 threads per inch (1.27 mm pitch). They may start together for a turn but will cross-thread.
What does M10 × 1.25 mean?
A metric thread with a 10 mm major diameter and 1.25 mm pitch: the fine-pitch version of M10 (coarse is 1.5). Tap it with an 8.75 mm drill.
Sources
- ISO 261:1998, ISO general purpose metric screw threads, general plan
- ISO 262:1998, ISO general purpose metric screw threads, selected sizes for screws, bolts and nuts
- ISO 724:1993, ISO general-purpose metric screw threads, basic dimensions
- ISO 273:1979, Fasteners, clearance holes for bolts and screws
- Engineering Hardware / isocnc / mechcodex: ISO 273 clearance hole tables (cross-check)
- DIN 336: Drill diameters for tapping holes (tap drill sizes)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.