Sandpaper Grit Chart: FEPA P and CAMI
The grit number counts mesh openings per inch of the sieve that sorts the grains, so a higher number is a finer abrasive. Two scales are in use: FEPA 'P' grades (P120) on most paper sold in Europe and online, and CAMI grades (plain '120') in the US. They match up to about 220; above that a P-grade is coarser than the CAMI grade with the same number: P400 is about 35 µm, CAMI 400 about 24 µm.
Grit chartTap a grit for particle size and use
| Grit | Average particle sizeµm | Nearest grade, other system | Typical use |
|---|---|---|---|
| FEPA P-grades (ISO 6344) | |||
| P12 | 1815 | CAMI 16 | Extra coarse: stripping paint, floor sanding first pass |
| P16 | 1324 | CAMI 16 | Extra coarse: stripping paint, floor sanding first pass |
| P20 | 1000 | CAMI 20 | Extra coarse: stripping paint, floor sanding first pass |
| P24 | 764 | CAMI 24 | Extra coarse: stripping paint, floor sanding first pass |
| P30 | 642 | CAMI 24 | Extra coarse: stripping paint, floor sanding first pass |
| P36 | 538 | CAMI 36 | Extra coarse: stripping paint, floor sanding first pass |
| P40 | 425 | CAMI 40 | Coarse: shaping, removing old finish, rough lumber |
| P50 | 336 | CAMI 50 | Coarse: shaping, removing old finish, rough lumber |
| P60 | 269 | CAMI 60 | Coarse: shaping, removing old finish, rough lumber |
| P80 | 201 | CAMI 80 | Medium: smoothing bare wood, removing planer marks |
| P100 | 162 | CAMI 100 | Medium: smoothing bare wood, removing planer marks |
| P120 | 125 | CAMI 120 | Medium: smoothing bare wood, removing planer marks |
| P150 | 100 | CAMI 150 | Fine: final sanding of bare wood before finishing |
| P180 | 82 | CAMI 180 | Fine: final sanding of bare wood before finishing |
| P220 | 68 | CAMI 220 | Very fine: sanding between coats |
| P240 | 58.5 | CAMI 240 | Very fine: sanding between coats |
| P280 | 52.2 | CAMI 240 | Very fine: sanding between coats |
| P320 | 46.2 | CAMI 280 | Very fine: sanding between coats |
| P360 | 40.5 | CAMI 280 | Extra fine: wet sanding paint, primer and sealer |
| P400 | 35 | CAMI 320 | Extra fine: wet sanding paint, primer and sealer |
| P500 | 30.2 | CAMI 360 | Extra fine: wet sanding paint, primer and sealer |
| P600 | 25.8 | CAMI 400 | Extra fine: wet sanding paint, primer and sealer |
| P800 | 21.8 | CAMI 400 | Ultra fine: polishing, clear coat before buffing |
| P1000 | 18.3 | CAMI 500 | Ultra fine: polishing, clear coat before buffing |
| P1200 | 15.3 | CAMI 600 | Ultra fine: polishing, clear coat before buffing |
| P1500 | 12.6 | CAMI 800 | Ultra fine: polishing, clear coat before buffing |
| P2000 | 10.3 | CAMI 1000 | Ultra fine: polishing, clear coat before buffing |
| P2500 | 8.4 | CAMI 1000 | Ultra fine: polishing, clear coat before buffing |
| CAMI / ANSI grades (US) | |||
| CAMI 16 | 1320 | P16 | Extra coarse: stripping paint, floor sanding first pass |
| CAMI 20 | 905 | P20 | Extra coarse: stripping paint, floor sanding first pass |
| CAMI 24 | 715 | P24 | Extra coarse: stripping paint, floor sanding first pass |
| CAMI 36 | 530 | P36 | Extra coarse: stripping paint, floor sanding first pass |
| CAMI 40 | 425 | P40 | Coarse: shaping, removing old finish, rough lumber |
| CAMI 50 | 348 | P50 | Coarse: shaping, removing old finish, rough lumber |
| CAMI 60 | 265 | P60 | Coarse: shaping, removing old finish, rough lumber |
| CAMI 80 | 190 | P80 | Medium: smoothing bare wood, removing planer marks |
| CAMI 100 | 140 | P120 | Medium: smoothing bare wood, removing planer marks |
| CAMI 120 | 115 | P120 | Medium: smoothing bare wood, removing planer marks |
| CAMI 150 | 92 | P150 | Fine: final sanding of bare wood before finishing |
| CAMI 180 | 82 | P180 | Fine: final sanding of bare wood before finishing |
| CAMI 220 | 68 | P220 | Very fine: sanding between coats |
| CAMI 240 | 53.5 | P280 | Very fine: sanding between coats |
| CAMI 280 | 44 | P320 | Very fine: sanding between coats |
| CAMI 320 | 36 | P400 | Extra fine: wet sanding paint, primer and sealer |
| CAMI 360 | 28.8 | P500 | Extra fine: wet sanding paint, primer and sealer |
| CAMI 400 | 23.6 | P800 | Extra fine: wet sanding paint, primer and sealer |
| CAMI 500 | 19.7 | P1000 | Ultra fine: polishing, clear coat before buffing |
| CAMI 600 | 16 | P1200 | Ultra fine: polishing, clear coat before buffing |
| CAMI 800 | 12.2 | P1500 | Ultra fine: polishing, clear coat before buffing |
| CAMI 1000 | 9.2 | P2500 | Ultra fine: polishing, clear coat before buffing |
No exact match. The nearest sizes:
How to read a grit marking
A P in front of the number (P120, P-120) means the FEPA grading of ISO 6344. A plain number (120) on US paper is usually CAMI (ANSI B74.18). Up to about 220 the two scales are close enough to use interchangeably; from 240 upward compare the micron sizes in the chart instead of the numbers.
The number comes from sieving: grit 60 passes a screen with roughly 60 openings per linear inch. Fine grades are sorted by sedimentation instead, but keep the same numbering idea: bigger number, smaller grain.
Microfinishing films and polishing papers are often graded directly in microns (µm) or with Japanese JIS numbers; the micron column lets you place them next to P and CAMI grades.
Besides grit, sandpaper is described by mineral (aluminium oxide for wood and metal, silicon carbide for wet sanding, ceramic for heavy stock removal, garnet for hand-sanding wood), backing (paper weight A–F, cloth, film) and coat (open coat clogs less on wood and paint).
About Sandpaper Grit
Sand in steps. Start with the finest grit that removes the defect in reasonable time, then move up through the grades without skipping more than about one step (the next grit should be no more than about 1.5–2 times finer), so each grit removes the scratches of the last. A common sequence for bare wood is P80 → P120 → P180, finishing at P180–P220 before stain or oil. Between coats of varnish or paint use P240–P320; wet sand topcoats with P600–P2000 before polishing.
Do not sand bare wood finer than about P220 before staining: very fine sanding burnishes the surface and the stain takes up unevenly. On end grain one step finer helps to even out the color.
The particle sizes here are averages. Both standards allow a spread of grain sizes around the average, and CAMI's tolerance is wider than FEPA's, which is another reason premium papers usually carry P-grades.
Why P400 is not CAMI 400
The two standards set their fine grades from different reference sizes. At the coarse end they coincide (P40 and CAMI 40 are both about 425 µm), but the CAMI scale shrinks faster: P400 ≈ 35 µm while CAMI 400 ≈ 24 µm, P1000 ≈ 18 µm while CAMI 1000 ≈ 9 µm. Following a US tutorial with European paper therefore means going one or two steps higher in number: CAMI 400 falls between P600 and P800.
ANSI B74.18 grades coated abrasives up to CAMI 600; the CAMI 800 and 1000 sizes here are commonly published manufacturer values, and sources differ by 5–10 % on many CAMI averages (for example CAMI 100: 140 or 148 µm).
Questions
What grit sandpaper should I use for wood?
Start with P80 for rough or marked wood, P120 for already smooth wood, and finish at P180–P220 before staining or oiling. Sand between coats of finish with P240–P320.
Is P400 the same as 400 grit?
No. P400 (FEPA) is about 35 µm; CAMI 400 is about 24 µm, between P600 and P800. Below about 220 the P and CAMI numbers are nearly equivalent.
What does the P mean on sandpaper?
It marks the FEPA grading system defined in ISO 6344. A grit without the P is usually CAMI (US) grading.
What grit is used for wet sanding a car?
Typically P400–P600 for primer, P800–P1500 for base and clear coat repairs, and P2000–P3000 before machine polishing.
How many microns is 120 grit?
P120 averages about 125 µm, CAMI 120 about 115 µm.
Sources
- ISO 6344-2 / 6344-3: Coated abrasives, grain size analysis (FEPA P12–P2500)
- FEPA: Federation of European Producers of Abrasives, P-grade standards 43-1 and 43-2
- ANSI B74.18: Grading of certain abrasive grain on coated abrasive products (CAMI)
- sizes.com: Sandpaper (coated abrasives) grit sizes
- Fine-Tools: Comparison of abrasive grain sizes
- Seabean: Grit scales comparison chart
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.