Concrete Anchor Drill Bit Size Chart
Which drill bit each concrete anchor needs. For wedge and sleeve anchors the bit equals the anchor diameter (3/8 in anchor, 3/8 in bit; M10 throughbolt, 10 mm bit). Drop-in anchors need a larger bit (3/8 in drop-in, 1/2 in bit) and concrete screws a smaller one.
Size chartEmbedment shown only where it is standard; otherwise follow the anchor's data sheet
| Anchor | Thread / bolt | Drill bit diametermminmm · in | Min. embedment / hole depthmminmm · in |
|---|---|---|---|
| Wedge anchors (inch): drill = anchor diameter | |||
| 1/4″ wedge | 1/4″ UNC | 6.41/4 | 291 1/8 |
| 3/8″ wedge | 3/8″ UNC | 9.53/8 | 381 1/2 |
| 1/2″ wedge | 1/2″ UNC | 12.71/2 | 572 1/4 |
| 5/8″ wedge | 5/8″ UNC | 15.95/8 | 702 3/4 |
| 3/4″ wedge | 3/4″ UNC | 19.13/4 | 833 1/4 |
| 7/8″ wedge | 7/8″ UNC | 22.27/8 | — |
| 1″ wedge | 1″ UNC | 25.41 | — |
| Drop-in anchors (inch): internally threaded, larger bit | |||
| 1/4″ drop-in | 1/4″ UNC (internal) | 9.53/8 | 251 |
| 3/8″ drop-in | 3/8″ UNC (internal) | 12.71/2 | 401.563 |
| 1/2″ drop-in | 1/2″ UNC (internal) | 15.95/8 | 512 |
| 5/8″ drop-in | 5/8″ UNC (internal) | 22.27/8 | 642 1/2 |
| 3/4″ drop-in | 3/4″ UNC (internal) | 25.41 | 813.187 |
| Sleeve anchors (inch): drill = sleeve diameter | |||
| 1/4″ sleeve | #10 bolt | 6.41/4 | — |
| 5/16″ sleeve | 1/4″ bolt | 7.90.313 | — |
| 3/8″ sleeve | 5/16″ bolt | 9.53/8 | — |
| 1/2″ sleeve | 3/8″ bolt | 12.71/2 | — |
| 5/8″ sleeve | 1/2″ bolt | 15.95/8 | — |
| 3/4″ sleeve | 5/8″ bolt | 19.13/4 | — |
| Concrete screws (inch): Tapcon type and large screw anchors | |||
| 3/8″ screw anchor | 3/8″ screw anchor | 9.53/8 | — |
| 1/2″ screw anchor | 1/2″ screw anchor | 12.71/2 | — |
| 5/8″ screw anchor | 5/8″ screw anchor | 15.95/8 | — |
| 3/4″ screw anchor | 3/4″ screw anchor | 19.13/4 | — |
| Metric wedge anchors / throughbolts: drill = thread size | |||
| M6 wedge | M6 | 60.236 | — |
| M8 wedge | M8 | 80.315 | — |
| M10 wedge | M10 | 100.394 | — |
| M12 wedge | M12 | 120.472 | — |
| M16 wedge | M16 | 160.630 | — |
| M20 wedge | M20 | 200.787 | — |
| M24 wedge | M24 | 240.945 | — |
| Metric drop-in anchors | |||
| M6 drop-in | M6 (internal) | 80.315 | 250.984 |
| M8 drop-in | M8 (internal) | 100.394 | 301.181 |
| M10 drop-in | M10 (internal) | 120.472 | 401.575 |
| M12 drop-in | M12 (internal) | 150.591 | 501.969 |
| M16 drop-in | M16 (internal) | 200.787 | 652.559 |
| M20 drop-in | M20 (internal) | 250.984 | 803.150 |
| Metric concrete screws, named by drill diameter | |||
| 6 mm concrete screw | 6 mm screw anchor | 60.236 | — |
| 8 mm concrete screw | 8 mm screw anchor | 80.315 | — |
| 10 mm concrete screw | 10 mm screw anchor | 100.394 | — |
| 12 mm concrete screw | 12 mm screw anchor | 120.472 | — |
| 14 mm concrete screw | 14 mm screw anchor | 140.551 | — |
No exact match. The nearest sizes:
How to pick the bit and the hole depth
Wedge and sleeve anchors go through the fixture into the concrete: drill the fixture hole and the concrete hole with the same bit as the anchor diameter, using a carbide bit to ANSI B212.15 (inch) or a metric SDS bit. A worn bit makes the hole too small; a bit that wobbles makes it too big and the wedge will spin.
Embedment is measured from the concrete surface to the bottom of the expansion clip (wedge) or the end of the anchor. Drill at least 1/2 in (12 mm) deeper than the embedment so dust has somewhere to go, or blow and brush the hole clean. Dust in the hole is the most common cause of low pull-out strength.
Drop-in anchors are set flush in a hole drilled to the anchor length with the larger bit listed, then expanded with the setting tool until the tool's shoulder touches the anchor. Concrete screws cut their own thread: the bit is smaller than the screw, and the hole must be at least 1/4 in deeper than the screw goes in.
About Concrete Anchors
Capacity depends on the concrete strength, edge distance, spacing and embedment, not only on the anchor size. Published loads (ICC-ES reports in the US, European Technical Assessments in Europe) assume minimum edge distances of roughly 5–10 anchor diameters and spacing of about 10 diameters at full embedment. Closer to an edge, the concrete cone breaks out first.
Wedge anchors are the strongest common mechanical anchor and are only for solid concrete. Sleeve anchors also work in brick and block, with lower loads. Drop-in anchors give a flush internal thread for threaded rod hangers in ceilings and removable fixtures. Concrete screws are quick and removable; small Tapcon types suit light fixtures in concrete and block, large screw anchors (Titen HD type) carry structural loads and can go close to edges.
For tension loads in cracked concrete, seismic use or overhead life-safety loads, use only anchors rated for it (ICC-ES AC193 / AC308, ETA option 1) and follow the evaluation report for drill, depth, torque and spacing. Adhesive (chemical) anchors are the alternative where expansion stresses near edges are a problem.
Questions
What size drill bit for a 3/8 wedge anchor?
3/8 in. Wedge anchors use a bit equal to the anchor diameter: 1/4 in anchor 1/4 in bit, 1/2 in anchor 1/2 in bit. Minimum embedment for a 3/8 in Red Head Trubolt is 1-1/2 in; drill at least 1/2 in deeper.
What drill size for a 3/8 drop-in anchor?
1/2 in. Drop-in anchors take a bit one size larger than the internal thread: 1/4 in drop-in 3/8 in bit, 1/2 in drop-in 5/8 in bit, 5/8 in drop-in 7/8 in bit. Drill to the anchor length, 1-9/16 in for a standard 3/8 in drop-in.
What drill bit for an M10 anchor bolt?
10 mm for an M10 wedge anchor (throughbolt). An M10 drop-in anchor needs a 12 mm hole 40 mm deep; an M10 sleeve anchor usually needs 15 or 16 mm; check the sleeve diameter on the box.
How deep should the hole be for a wedge anchor?
At least the minimum embedment plus 1/2 in (12 mm): for a 1/2 in wedge anchor with 2-1/4 in minimum embedment, drill 2-3/4 in or deeper. Thread the nut on, tap the anchor in, then torque to the maker's value.
Sources
- ANSI B212.15: Carbide-tipped masonry drill bits (bit diameters for anchors)
- ITW Red Head: Trubolt wedge anchor technical data / ICC-ES ESR-2251
- Simpson Strong-Tie: Drop-in (DIAB) and Titen HD installation data
- DeWALT / Powers: Steel Dropin product data
- ITW Buildex: Tapcon concrete screw installation guide
- Walraven WDI1 / RS Pro: metric drop-in anchor data sheets
- EAD 330232 / ETA assessments: mechanical fasteners for concrete (metric anchors)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.