Metric Hex Bolt Size Chart

Head dimensions of metric hexagon head bolts and screws to ISO 4014 and ISO 4017. The width across flats s is the wrench size: 10 mm for M6, 13 mm for M8, and 16 mm for M10 under ISO, 17 mm under the old DIN 933.

29 sizesChecked 2026-11-154 sources
M3 – M14M35.5M47M58M610M813M1016 / 17M1218 / 19M1421 / 22M16 – M48 (smaller scale)M1624M2030M2234 / 32M2436M3046M3655M4265M4875
Top views at two scales. Numbers under each head: width across flats in mm (ISO / old DIN where they differ, DIN outline dashed).Drawn to scale · Dimensions in mmDimensions in inches

Size chartTap a size for its drawing and full specs

29 of 29
SizePThread pitchmmTPIsWidth across flats (ISO)mminWidth across flats (DIN 931/933)mminkHead heightmmineWidth across corners (min.)mmin
M1.60.3572.63.20.1263.20.1261.10.0433.410.134
M20.463.540.15740.1571.40.0554.320.170
M2.50.4556.450.19750.1971.70.0675.450.215
M30.550.85.50.2175.50.21720.0796.010.237
M3.50.642.360.23660.2362.40.0946.580.259
M40.736.370.27670.2762.80.1107.660.302
M50.831.780.31580.3153.50.1388.790.346
M6125.4100.394100.39440.15711.050.435
M81.2520.3130.512130.5125.30.20914.380.566
M101.516.9160.630170.6696.40.25217.770.700
M121.7514.5180.709190.7487.50.29520.030.789
M14212.7210.827220.8668.80.34623.360.920
M16212.7240.945240.945100.39426.751.053
M182.510.2271.063271.06311.50.45330.141.187
M202.510.2301.181301.18112.50.49233.531.320
M222.510.2341.339321.260140.55137.721.485
M2438.5361.417361.417150.59139.981.574
M2738.5411.614411.614170.66945.21.780
M303.57.3461.811461.81118.70.73650.852.002
M333.57.3501.969501.969210.82755.372.180
M3646.4552.165552.16522.50.88660.792.393
M3946.4602.362602.362250.98466.442.616
M424.55.6652.559652.559261.02471.32.807
M454.55.6702.756702.756281.10276.953.030
M4855.1752.953752.953301.18182.63.252
M5255.1803.150803.150331.29988.253.474
M565.54.6853.346853.346351.37893.563.683
M605.54.6903.543903.543381.49699.213.906
M6464.2953.740953.740401.575104.864.128

How to read a hex bolt designation and measure the head

A hex bolt is ordered as standard – thread × length – property class: ISO 4017 – M8 × 30 – 8.8. ISO 4014 (formerly DIN 931) is a bolt with a plain shank and a thread only near the end; ISO 4017 (formerly DIN 933) is threaded right up to the head and is often called a hex cap screw or set screw in the UK. Their heads are identical.

The head is marked with the property class (8.8, 10.9, 12.9; stainless A2-70, A4-80) and the maker's mark. Length is measured from under the head to the end of the bolt.

Measure s across two parallel flats; that is the wrench or socket size. e, across the corners, is about 15 % larger and is what decides whether the head fits into a counterbore or next to a wall. k is the head height from the bearing face to the top.

About Hex Bolts

Head sizes come from ISO 4014 and ISO 4017 (product grades A and B); the widths across flats follow the ISO 272 series. Product grade A (tighter tolerances) covers M1.6 to M24 up to a length of 10 d or 150 mm; larger bolts are grade B, so the across-corners values from M27 up are grade B minimums.

When DIN 931 and 933 were replaced by ISO 4014 and 4017, four sizes got a smaller head: M10 17 → 16 mm, M12 19 → 18 mm, M14 22 → 21 mm, and M22 32 → 34 mm (the only one that grew). Both versions are still sold side by side, especially in Europe, so an M10 or M12 bolt may need either wrench. Japanese JIS bolts add their own small-head variants, common on cars: 12 mm on M8, 14 mm on M10 and 17 mm on M12.

Head heights are nominal values. A few DIN 933 heads are slightly taller than the ISO head (M10 7 mm vs 6.4 mm), which matters only in tight counterbores. Thread pitch is the ISO coarse pitch; fine-thread hex screws (ISO 8765 / ISO 8676) use the same heads.

Washers, nuts and wrenches for each size

The matching ISO 4032 nut has the same width across flats as the bolt head, so one wrench size serves both, except for ISO bolts combined with old DIN nuts (or vice versa) in the four sizes that changed. A flat washer to ISO 7089 has an outside diameter larger than e, so it supports the whole bearing face.

Questions

What size wrench fits an M8 bolt?

13 mm. The M8 hex head is 13 mm across the flats in both ISO 4017 and DIN 933.

Is an M10 bolt head 16 mm or 17 mm?

Both exist. ISO 4014/4017 heads are 16 mm; the older DIN 931/933 heads are 17 mm. Check the bolt with a caliper or try both wrenches. The same split applies to M12 (18 / 19 mm) and M14 (21 / 22 mm).

What is the difference between ISO 4014 and ISO 4017?

ISO 4014 is a partially threaded bolt (plain shank under the head), the successor of DIN 931. ISO 4017 is threaded all the way to the head, successor of DIN 933. Head dimensions are the same.

What wrench size for M6, M12 and M16 bolts?

M6: 10 mm. M12: 18 mm (ISO) or 19 mm (DIN). M16: 24 mm. M20: 30 mm, M24: 36 mm.

What do the numbers 8.8 or 10.9 on the bolt head mean?

The property class. The first number × 100 is the tensile strength in MPa (8 → 800 MPa), the second is the ratio of yield to tensile strength (.8 → 80 %). So 8.8 yields at about 640 MPa, 10.9 at about 900 MPa.

Sources

  1. ISO 4014:2022, Fasteners, hexagon head bolts, product grades A and B
  2. ISO 4017:2022, Fasteners, hexagon head screws, product grades A and B
  3. ISO 272:1982, Fasteners, hexagon products, widths across flats
  4. DIN 933 / DIN 931 (withdrawn): Hexagon head screws and bolts, as reproduced in Böllhoff and Würth data sheets

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.