Lifting Eye Bolt Size Chart: DIN 580 & DIN 582

Working load limits and dimensions of collar-type lifting eye bolts (DIN 580) and lifting eye nuts (DIN 582) from M8 to M48. The rated load is for a straight vertical pull: an M12 eye bolt lifts 340 kg in line with the thread, but only about 240 kg per eye in a two-leg sling at 45°.

20 sizesChecked 2026-11-155 sources

Size chartTap a size for its drawing and full specs

20 of 20
SizeWLL, axial (single eye, vertical)tlbd₂Eye inside diametermmind₃Eye outside diametermmind₄Collar / body diametermminhHeight above bearing facemminlThread lengthmmineNut body heightmmin
DIN 580 lifting eye bolts (collar eye bolts)
M8 DIN 5800.14309200.79361.42200.79361.42130.51—
M10 DIN 5800.23507250.98451.77250.98451.77170.67—
M12 DIN 5800.34750301.18542.13301.18532.0920.50.81—
M16 DIN 5800.71,543351.38632.48351.38622.44271.06—
M20 DIN 5801.22,646401.57722.83401.57712.80301.18—
M24 DIN 5801.83,968501.97903.54501.97903.54361.42—
M30 DIN 5803.27,055602.361084.25652.561094.29451.77—
M36 DIN 5804.610,141702.761264.96752.951285.04542.13—
M42 DIN 5806.313,889803.151445.67853.351475.79632.48—
M48 DIN 5808.618,960903.541666.541003.941686.61682.68—
DIN 582 lifting eye nuts
M8 DIN 5820.14309200.79361.42200.79361.42—8.50.33
M10 DIN 5820.23507250.98451.77250.98451.77—100.39
M12 DIN 5820.34750301.18542.13301.18532.09—110.43
M16 DIN 5820.71,543351.38632.48351.38622.44—130.51
M20 DIN 5821.22,646401.57722.83401.57712.80—160.63
M24 DIN 5821.83,968501.97903.54501.97903.54—200.79
M30 DIN 5823.27,055602.361084.25652.561094.29——
M36 DIN 5824.610,141702.761264.96752.951285.04——
M42 DIN 5826.313,889803.151445.67853.351475.79——
M48 DIN 5828.618,960903.541666.541003.941686.61——

How to read and use a DIN eye bolt

The marking on the eye gives the standard, the thread and usually the WLL, for example DIN 580 C15E M16 0.7 t. C15E is the case-hardening steel the standard specifies; stainless versions (A2/A4) have their own, often lower ratings. For stainless, use the maker's table, not this one.

The axial WLL in the chart applies to a single eye bolt pulled straight along its axis. In a two-leg sling the load per eye must be reduced: makers' tables give about 70 % of the axial WLL per eye for sling angles up to 45° from vertical. DIN 580 eye bolts must not be loaded across the plane of the eye; use rotating lifting points (swivel eyes) for side loads.

Screw the eye bolt in until the collar sits flat and fully on the bearing surface, with the eye aligned to the direction of pull (use a shim washer if needed, never back the bolt off). The tapped hole needs at least the thread length l of full thread in steel; in cast iron or aluminium the engagement must be longer (typically 1.25–2 × d).

About Eye Bolts (DIN 580/582)

DIN 580 eye bolts screw into a tapped hole of the load, like the M12 hole on top of an electric motor or gearbox. DIN 582 eye nuts do the same job on a stud or a bolt end. Both share the same eye and collar dimensions and the same load ratings for each thread size.

The ratings step up with the thread: M8 0.14 t, M10 0.23 t, M12 0.34 t, M16 0.7 t, M20 1.2 t, M24 1.8 t, M30 3.2 t, M36 4.6 t, up to M48 at 8.6 t. The design factor is 6:1 against breaking. Older DIN 580 editions and some imported eye bolts carry slightly different numbers. If the stamp and the chart disagree, use the lower value.

Inspect before every lift: the collar must be undamaged and flat, the eye not bent or worn by more than 10 % of the section, the thread clean and complete. Do not weld on an eye bolt, do not heat it, and never put a hook point into the eye from the side. Use a shackle.

Questions

What is the working load of an M12 eye bolt?

340 kg (0.34 t) for a DIN 580 eye bolt pulled vertically in line with the thread. For two eye bolts in a two-leg sling up to 45°, use about 240 kg per eye. Side loading across the eye is not allowed.

What is the WLL of an M16 eye bolt?

700 kg (0.7 t) axial for DIN 580 in C15E steel; about 500 kg per eye in a two-leg sling up to 45°. An M20 is rated 1.2 t axial.

What is the difference between DIN 580 and DIN 582?

DIN 580 is an eye bolt with a male thread that screws into the load; DIN 582 is an eye nut with a female thread that screws onto a stud. The eye dimensions and ratings per thread size are the same.

Can I use an eye bolt at an angle?

Only in the plane of the eye and with reduced load: about 70 % of the axial WLL per eye up to 45° from vertical, per the maker's table. Loads across the eye plane bend the shank. For angled or rotating loads use swivel lifting points.

How deep should the tapped hole be for an eye bolt?

At least the eye bolt thread length (for example 20.5 mm for M12, 27 mm for M16) of full thread in steel. In grey cast iron and aluminium allow 1.25 to 2 times the thread diameter of engagement, and make sure the collar seats flat.

Sources

  1. DIN 580:2010, Lifting eye bolts
  2. DIN 582:2010, Lifting eye nuts
  3. Ganter: DIN 580 / DIN 582 lifting eye bolts and nuts, steel (dimension and load tables)
  4. fasteners.eu: DIN 580 and DIN 582 dimension tables
  5. JC Fasteners: DIN 580 lifting eye bolt data sheet

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.