Dowel Pin, Spring Pin and Cotter Pin Sizes (Metric)

Three kinds of pin locate and secure parts. A dowel pin is ground to tolerance m6 and pressed into an H7 reamed hole; a slotted spring pin goes into a plain drilled hole of its nominal size; a cotter (split) pin is named after the hole it fits, so a 4 mm cotter pin is 3.7 mm thick and goes through a 4 mm hole.

40 pinsChecked 2026-11-156 sources
Dowel pin (ISO 8734)dSlotted spring pin (ISO 8752)dSplit / cotter pin (ISO 1234)bca
Schematic: d = nominal diameter; cotter pin b = eye length, c = eye width, a = prong extension.Proportions shown, not to scale · Dimensions in mmDimensions in inches

Pin chartSort by any column, or filter to find a row

40 of 40
PindNominal diameter / holemminPin toleranceHole tolerancedWire diameter (max)mmincEye width (max)mminbEye length (approx.)mminaProng extension (max)mmin
Dowel pins: ISO 8734 (hardened) / ISO 2338
1 mm dowel pin10.039m6H7————
1.5 mm dowel pin1.50.059m6H7————
2 mm dowel pin20.079m6H7————
2.5 mm dowel pin2.50.098m6H7————
3 mm dowel pin30.118m6H7————
4 mm dowel pin40.157m6H7————
5 mm dowel pin50.197m6H7————
6 mm dowel pin60.236m6H7————
8 mm dowel pin80.315m6H7————
10 mm dowel pin100.394m6H7————
12 mm dowel pin120.472m6H7————
16 mm dowel pin160.630m6H7————
20 mm dowel pin200.787m6H7————
Slotted spring pins: ISO 8752 / ISO 13337
1 mm spring pin10.039—H12————
1.5 mm spring pin1.50.059—H12————
2 mm spring pin20.079—H12————
2.5 mm spring pin2.50.098—H12————
3 mm spring pin30.118—H12————
4 mm spring pin40.157—H12————
5 mm spring pin50.197—H12————
6 mm spring pin60.236—H12————
8 mm spring pin80.315—H12————
10 mm spring pin100.394—H12————
12 mm spring pin120.472—H12————
16 mm spring pin160.630—H12————
20 mm spring pin200.787—H12————
Split (cotter) pins: ISO 1234 / DIN 94
0.6 mm cotter pin0.60.024——0.50.02010.03920.0791.60.063
0.8 mm cotter pin0.80.031——0.70.0281.40.0552.40.0941.60.063
1 mm cotter pin10.039——0.90.0351.80.07130.1181.60.063
1.2 mm cotter pin1.20.047——10.03920.07930.1182.50.098
1.6 mm cotter pin1.60.063——1.40.0552.80.1103.20.1262.50.098
2 mm cotter pin20.079——1.80.0713.60.14240.1572.50.098
2.5 mm cotter pin2.50.098——2.30.0914.60.18150.1972.50.098
3.2 mm cotter pin3.20.126——2.90.1145.80.2286.40.2523.20.126
4 mm cotter pin40.157——3.70.1467.40.29180.31540.157
5 mm cotter pin50.197——4.60.1819.20.362100.39440.157
6.3 mm cotter pin6.30.248——5.90.23211.80.46512.60.49640.157
8 mm cotter pin80.315——7.50.295150.591160.63040.157
10 mm cotter pin100.394——9.50.374190.748200.7876.30.248
13 mm cotter pin130.512——12.40.48824.80.976261.0246.30.248

How the pins are sized

Dowel pins are named by their diameter. Hardened dowel pins (ISO 8734, formerly DIN 6325) are ground to m6, slightly oversize, and give a light press fit in a hole reamed to H7. Unhardened ISO 2338 pins come in m6 and h8. For a slip-fit locating pin, ream the second part slightly larger (F7 or G7) so it can be separated.

Slotted spring pins (roll pins) are named by the hole: a 4 mm spring pin goes into a 4 mm drilled hole (tolerance H12) and is compressed on assembly. ISO 8752 is the heavy-duty type, ISO 13337 the light type; their wall thicknesses differ and are not listed here.

Cotter pins are also named by the hole diameter. The wire is smaller (d max), c is the eye width, b the eye length and a how far the longer prong extends. Choose the largest pin that fits the hole in the bolt or clevis pin.

About Dowel, Spring & Cotter Pins

Pins carry shear loads and fix the position of parts relative to each other. A dowel pin pair locates a cover or fixture to within a few hundredths of a millimetre, independently of the bolts that clamp it. Two dowels per joint are the norm; more over-constrains it.

Spring pins are cheaper and need no reaming. They hold by spring pressure and are used for hinges, levers, shafts and knobs. Coiled spring pins (ISO 8750) spread load better and survive vibration longer than slotted ones.

Cotter pins secure castle nuts, clevis pins and linkages. Bend the longer prong back over the end and the shorter one along the side; never re-use a bent cotter pin.

Questions

What hole size for a 6 mm dowel pin?

Ream to 6 mm H7 (6.000–6.012 mm) for a hardened m6 dowel pin (6.004–6.012 mm), a light press fit. For a removable part, ream the second hole slightly larger, e.g. 6 mm G7.

What size hole for a 5 mm spring pin?

A 5 mm drilled hole (H12). Spring pins are sized by the hole they go into.

What size is a 4 mm cotter pin?

It fits a 4 mm hole: wire up to 3.7 mm, eye up to 7.4 mm wide and about 8 mm long (ISO 1234).

What is the difference between ISO 8734 and ISO 2338 dowels?

ISO 8734 pins are hardened and ground (m6); ISO 2338 pins are unhardened steel or austenitic stainless in tolerance m6 or h8.

Sources

  1. ISO 8734:1997, Parallel pins of hardened steel and martensitic stainless steel (dowel pins)
  2. ISO 2338:1997, Parallel pins of unhardened steel and austenitic stainless steel
  3. ISO 8752:2009, Spring-type straight pins, slotted, heavy duty
  4. ISO 1234:1997, Split pins (sample: Table 1)
  5. Böllhoff: DIN 94 split pins, stainless A2 data sheet
  6. AmesWeb: Split pin dimensions

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.