Metric Set Screw Sizes (Grub Screws, DIN 913–916)
A set screw (grub screw) is fully threaded with no head and a hex socket in one end. Four point shapes are standardised (flat, cone, dog and cup), and all four use the same hex key for a given thread: 1.5 mm for M3, 2 mm for M4, 2.5 mm for M5, 3 mm for M6.
Size chartTap a size for its drawing and full specs
| Thread | PPitchmmin | sHex key sizemmin | dpFlat / dog point dia. (max)mmin | dtCone point tip dia. (max)mmin | dzCup point dia. (max)mmin | z1Dog length, short (min)mmin | z2Dog length, long (min)mmin |
|---|---|---|---|---|---|---|---|
| M1.6 | 0.350.0138 | 0.70.028 | 0.80.031 | 0.40.0157 | 0.80.031 | 0.40.0157 | 0.80.0315 |
| M2 | 0.40.0157 | 0.90.035 | 10.039 | 0.50.0197 | 10.039 | 0.50.0197 | 10.0394 |
| M2.5 | 0.450.0177 | 1.30.051 | 1.50.059 | 0.650.0256 | 1.20.047 | 0.630.0248 | 1.250.0492 |
| M3 | 0.50.0197 | 1.50.059 | 20.079 | 0.750.0295 | 1.40.055 | 0.750.0295 | 1.50.0591 |
| M4 | 0.70.0276 | 20.079 | 2.50.098 | 10.0394 | 20.079 | 10.0394 | 20.0787 |
| M5 | 0.80.0315 | 2.50.098 | 3.50.138 | 1.250.0492 | 2.50.098 | 1.250.0492 | 2.50.0984 |
| M6 | 10.0394 | 30.118 | 40.157 | 1.50.0591 | 30.118 | 1.50.0591 | 30.1181 |
| M8 | 1.250.0492 | 40.157 | 5.50.217 | 20.0787 | 50.197 | 20.0787 | 40.1575 |
| M10 | 1.50.0591 | 50.197 | 70.276 | 2.50.0984 | 60.236 | 2.50.0984 | 50.1969 |
| M12 | 1.750.0689 | 60.236 | 8.50.335 | 30.1181 | 80.315 | 30.1181 | 60.2362 |
| M16 | 20.0787 | 80.315 | 120.472 | 40.1575 | 100.394 | 40.1575 | 80.3150 |
| M20 | 2.50.0984 | 100.394 | 150.591 | 50.1969 | 140.551 | 50.1969 | 100.3937 |
| M24 | 30.1181 | 120.472 | 180.709 | 60.2362 | 160.630 | 60.2362 | 120.4724 |
No exact match. The nearest sizes:
Choosing the point and reading the size
Cup point (ISO 4029, DIN 916) is the default: the sharp ring bites into a shaft and holds well against vibration. Flat point (ISO 4026, DIN 913) leaves only a light mark. Use it on a flat ground on the shaft or where you adjust often. Cone point (ISO 4027, DIN 914) sits in a drilled dimple for a positive, repeatable position. Dog point (ISO 4028, DIN 915) engages a hole or slot and works as a pin; the long dog (z2) is the normal one, the short dog is for the shortest lengths.
A set screw is designated by thread, length and standard: ISO 4029 – M6 × 10 – 45H is an M6 cup point 10 mm long in hardness class 45H. Set screws are not made in property classes like bolts; steel ones are 45H (hardened to about 45 HRC), stainless ones A1-12H, A2-21H or A4-21H.
The length is the overall length, point included. To measure an unknown grub screw, measure the outside of the thread with a caliper (an M5 reads about 4.8–4.9 mm) and try the matching hex key.
About Set Screws
Socket set screws hold pulleys, gears, collars and knobs on shafts, and make adjusting screws in fixtures. The holding force comes from the axial force of the screw pressing its point into the shaft, so the hex key size directly limits how much you can tighten it. A 1.5 mm key in an M3 set screw strips long before the thread does.
The DIN standards 913 to 916 were replaced by ISO 4026 to 4029 with identical dimensions, so DIN and ISO set screws are fully interchangeable. Both are still printed on packaging.
Point diameters in the chart are maximum values. The cone point tip is one quarter of the thread diameter (M8: 2 mm). On a cup point, the cup diameter is roughly half the thread for small sizes and two-thirds for large ones.
Two set screws, or one?
For a pulley on a plain shaft, two set screws 90° apart hold much better than one; for a pulley that must not slip, file or mill a flat under the screw and use a flat or cup point on it. A second set screw on top of the first (a jam screw) locks it against vibration, as does medium-strength threadlocker.
Inch set screws
Inch socket set screws (ASME B18.3) use inch hex keys: #4 0.050 in, #6 1/16 in, #8 5/64 in, #10 3/32 in, 1/4 in 1/8 in, 5/16 in 5/32 in, 3/8 in 3/16 in, 1/2 in 1/4 in. A metric key in an inch socket (or the reverse) is close enough to turn a loose screw and to round the socket when tight.
Questions
What size Allen key for an M4 grub screw?
2 mm. M3 takes 1.5 mm, M5 2.5 mm, M6 3 mm, M8 4 mm, M10 5 mm, M12 6 mm.
What is the difference between DIN 913 and DIN 916?
The point: DIN 913 (ISO 4026) has a flat point, DIN 916 (ISO 4029) a cup point. Thread, hex key and lengths are the same.
Which set screw point holds best on a round shaft?
The cup point. It cuts a ring into the shaft surface. For the best hold, also give the shaft a flat or a dimple. A cone point in a dimple is even more positive.
Are DIN and ISO set screws interchangeable?
Yes. ISO 4026–4029 took over the dimensions of DIN 913–916 unchanged.
Sources
- ISO 4026 / 4027 / 4028 / 4029: Hexagon socket set screws with flat, cone, dog and cup point
- Westfield Fasteners: ISO 4026 (DIN 913) flat point set screw dimensions
- Westfield Fasteners: ISO 4027 (DIN 914) cone point set screw dimensions
- Westfield Fasteners: ISO 4028 (DIN 915) dog point set screw dimensions
- Westfield Fasteners: ISO 4029 (DIN 916) cup point set screw dimensions
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.