ISO 286 Fits and Tolerances
An ISO fit such as H7/g6 pairs a hole tolerance class (capital letter) with a shaft class (small letter). The letter places the tolerance zone relative to the nominal size, the number sets its width (IT grade). At ⌀25 mm, H7/g6 gives 7–41 µm clearance; H7/p6 gives 1–35 µm interference.
Fit chartTap a fit for its full tolerance table
| Fit | Fit type | Hole limits at ⌀25 mm (µm) | Shaft limits at ⌀25 mm (µm) | Max. clearance at ⌀25 mmµmin | Min. clearance at ⌀25 mm (− = interference)µmin |
|---|---|---|---|---|---|
| Hole-basis fits (H hole) | |||||
| H11/c11 | Clearance | +130 / 0 | −110 / −240 | 3700.01457 | 1100.00433 |
| H9/d9 | Clearance | +52 / 0 | −65 / −117 | 1690.00665 | 650.00256 |
| H9/e9 | Clearance | +52 / 0 | −40 / −92 | 1440.00567 | 400.00157 |
| H8/f7 | Clearance | +33 / 0 | −20 / −41 | 740.00291 | 200.00079 |
| H7/f7 | Clearance | +21 / 0 | −20 / −41 | 620.00244 | 200.00079 |
| H7/g6 | Clearance | +21 / 0 | −7 / −20 | 410.00161 | 70.00028 |
| H7/h6 | Clearance | +21 / 0 | 0 / −13 | 340.00134 | 00.00000 |
| H8/h7 | Clearance | +33 / 0 | 0 / −21 | 540.00213 | 00.00000 |
| H11/h11 | Clearance | +130 / 0 | 0 / −130 | 2600.01024 | 00.00000 |
| H7/js6 | Transition | +21 / 0 | +6.5 / −6.5 | 27.50.00108 | −6.5−0.00026 |
| H7/k6 | Transition | +21 / 0 | +15 / +2 | 190.00075 | −15−0.00059 |
| H7/m6 | Transition | +21 / 0 | +21 / +8 | 130.00051 | −21−0.00083 |
| H7/n6 | Transition | +21 / 0 | +28 / +15 | 60.00024 | −28−0.00110 |
| H7/p6 | Interference | +21 / 0 | +35 / +22 | −1−0.00004 | −35−0.00138 |
| H7/r6 | Interference | +21 / 0 | +41 / +28 | −7−0.00028 | −41−0.00161 |
| H7/s6 | Interference | +21 / 0 | +48 / +35 | −14−0.00055 | −48−0.00189 |
| Shaft-basis fits (h shaft) | |||||
| C11/h11 | Clearance | +240 / +110 | 0 / −130 | 3700.01457 | 1100.00433 |
| D9/h9 | Clearance | +117 / +65 | 0 / −52 | 1690.00665 | 650.00256 |
| F8/h7 | Clearance | +53 / +20 | 0 / −21 | 740.00291 | 200.00079 |
| G7/h6 | Clearance | +28 / +7 | 0 / −13 | 410.00161 | 70.00028 |
| K7/h6 | Transition | +6 / −15 | 0 / −13 | 190.00075 | −15−0.00059 |
| N7/h6 | Transition | −7 / −28 | 0 / −13 | 60.00024 | −28−0.00110 |
| P7/h6 | Interference | −14 / −35 | 0 / −13 | −1−0.00004 | −35−0.00138 |
| S7/h6 | Interference | −27 / −48 | 0 / −13 | −14−0.00055 | −48−0.00189 |
No exact match. The nearest sizes:
How to read a fit designation
⌀25 H7/g6 means: nominal size 25 mm, the hole made to tolerance class H7, the shaft to g6. Each class is a fundamental deviation letter plus an IT grade. The letter fixes where the zone sits relative to the nominal size (the zero line): for holes, A–G lie above it, H starts exactly at it, J/JS straddle it, K–ZC lie below it. Shaft letters mirror this: a–g below the zero line, h ending at it, js symmetric, k–zc above it.
The number is the IT grade: the width of the zone, which grows with size. At 18–30 mm, IT6 is 13 µm, IT7 21 µm, IT8 33 µm, IT9 52 µm and IT11 130 µm. H7 at ⌀25 therefore means 25.000 to 25.021 mm; g6 means 24.980 to 24.993 mm (−20 / −7 µm).
Clearance = hole minus shaft. Maximum clearance = upper hole limit − lower shaft limit (ES − ei); minimum clearance = lower hole limit − upper shaft limit (EI − es). A negative value is interference. In a clearance fit both are positive, in an interference fit both negative, in a transition fit the parts may end up either loose or tight depending on the actual sizes.
The chart shows the limits at ⌀25 mm only to compare fits at a glance. Open a fit (or use the calculator below) for the limits in every ISO size range from 0 to 500 mm.
About ISO Fits
ISO 286 is the international system of limits and fits, used for every machined bore and shaft from bearing seats to dowel pins. ANSI B4.2 adopts it unchanged for US metric work. The system has 28 deviation letters and 20 IT grades, but practice uses a small set: hole-basis fits with an H7 or H8 hole cover most machine design, because a reamed or bored H7 hole can be checked with one standard plug gauge and the fit is chosen by machining the shaft.
Shaft-basis fits (h shaft, e.g. G7/h6, K7/h6) are used where one ground shaft or a bought-in part with an h tolerance (drawn bar, dowel pins, bearing outer rings in the housing) carries several parts with different fits.
The tolerances on this page are computed from the ISO 286-1 IT grades and fundamental deviations and match the ISO 286-2 tables, including the Δ correction for K, M, N holes up to IT8 and P to S holes up to IT7 and the intermediate size ranges for c, r and s. Values are in micrometres (1 µm = 0.001 mm ≈ 0.00004 in).
Choose the loosest fit that does the job: tighter fits cost more to make and assemble. Common choices: running shafts H8/f7 or H7/f7; sliding and locating H7/g6 and H7/h6; hubs and gears that must come off H7/k6; parts that must not slip without a key H7/p6, H7/r6 or H7/s6 (press or shrink fit).
Fits for rolling bearings
Bearing rings have their own tolerances (bore deviation is always negative, ISO 492), so the usual shaft classes behave tighter than with an H hole. Typical rotating-shaft seats are j6, k5, k6 and m6; housings H7 or J7 for a stationary outer ring. Take the exact recommendation from the bearing maker's catalogue for the load and speed.
Press fit, shrink fit and transition fit
Interference fits up to about H7/p6 can usually be pressed together cold. H7/r6 and H7/s6 at medium and large sizes need heavy presses or thermal assembly: heat the hub or cool the shaft so that the interference plus an assembly clearance is taken up. Transition fits (js6, k6, m6, n6) locate accurately; k6 parts can be tapped together with a mallet, n6 needs a press.
Surface finish and measurement
An IT7 hole at ⌀25 has only 21 µm of tolerance. The surface roughness peaks are part of the measured size and are flattened on assembly, so a press fit with a rough surface loses part of its interference. Ground or finely turned shafts (Ra 0.4–0.8 µm) and reamed or honed holes are normal for IT6/IT7.
Questions
What is the tolerance of H7?
H7 starts at the nominal size and goes up by the IT7 value: +0/+10 µm up to 3 mm, +12 (3–6 mm), +15 (6–10), +18 (10–18), +21 (18–30), +25 (30–50), +30 (50–80), +35 (80–120), +40 (120–180) and +46 µm (180–250 mm). A ⌀20 H7 hole is 20.000–20.021 mm.
What is the difference between H7/h6 and H7/g6?
Both are clearance fits. H7/h6 has zero minimum clearance (parts just slide together by hand); H7/g6 adds a small guaranteed clearance (7 µm at ⌀25), so parts slide and turn freely. Use g6 for moving parts, h6 for locating parts that stay put.
Which fit is a press fit?
H7/p6 is the lightest standard press fit (at ⌀25: 1–35 µm interference). H7/r6 (7–41 µm) and H7/s6 (14–48 µm) are heavier. Transition fits like H7/n6 often need a press too, but may come out with a little clearance.
What does k6 mean on a shaft?
k6 is a transition shaft tolerance: at ⌀25 it is +2/+15 µm (25.002–25.015 mm). With an H7 hole the fit ranges from 19 µm clearance to 15 µm interference. It is a common seat for gears, couplings and bearing inner rings.
What is the tolerance of h6?
h6 ends at the nominal size and goes down by IT6: 0/−6 µm up to 3 mm, −8 (3–6), −9 (6–10), −11 (10–18), −13 (18–30), −16 (30–50), −19 (50–80), −22 (80–120), −25 µm (120–180 mm). Ground shafts and dowel pins are often h6.
Hole basis or shaft basis?
Hole basis (H holes) is the default: reamers and plug gauges are needed for only one hole class per size, and the fit is chosen on the shaft, which is easier to turn or grind to size. Shaft basis (h shafts) pays off when one drawn or ground shaft carries several parts with different fits.
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.