Circlip Sizes and Groove Dimensions (DIN 471, DIN 472, DIN 6799)
A circlip is sized by the shaft or bore it fits (d1); the chart gives the groove you must machine for it (groove diameter d2 and groove width m) and the ring thickness s. A DIN 471 ring for a 20 mm shaft needs a 19 mm groove, 1.3 mm wide, and is 1.2 mm thick.
Size chartTap a ring for its groove drawing
| Ring | d1Shaft / bore diametermmin | d1Shaft range (E-clip)mmin | d2Groove diametermmin | mGroove width (min)mmin | sRing thicknessmmin |
|---|---|---|---|---|---|
| DIN 471: external rings for shafts | |||||
| DIN 471 – 3 mm | 30.118 | — | 2.80.110 | 0.50.0197 | 0.40.0157 |
| DIN 471 – 4 mm | 40.157 | — | 3.80.150 | 0.50.0197 | 0.40.0157 |
| DIN 471 – 5 mm | 50.197 | — | 4.80.189 | 0.70.0276 | 0.60.0236 |
| DIN 471 – 6 mm | 60.236 | — | 5.70.224 | 0.80.0315 | 0.70.0276 |
| DIN 471 – 7 mm | 70.276 | — | 6.70.264 | 0.90.0354 | 0.80.0315 |
| DIN 471 – 8 mm | 80.315 | — | 7.60.299 | 0.90.0354 | 0.80.0315 |
| DIN 471 – 9 mm | 90.354 | — | 8.60.339 | 1.10.0433 | 10.0394 |
| DIN 471 – 10 mm | 100.394 | — | 9.60.378 | 1.10.0433 | 10.0394 |
| DIN 471 – 11 mm | 110.433 | — | 10.50.413 | 1.10.0433 | 10.0394 |
| DIN 471 – 12 mm | 120.472 | — | 11.50.453 | 1.10.0433 | 10.0394 |
| DIN 471 – 13 mm | 130.512 | — | 12.40.488 | 1.10.0433 | 10.0394 |
| DIN 471 – 14 mm | 140.551 | — | 13.40.528 | 1.10.0433 | 10.0394 |
| DIN 471 – 15 mm | 150.591 | — | 14.30.563 | 1.10.0433 | 10.0394 |
| DIN 471 – 16 mm | 160.630 | — | 15.20.598 | 1.10.0433 | 10.0394 |
| DIN 471 – 17 mm | 170.669 | — | 16.20.638 | 1.10.0433 | 10.0394 |
| DIN 471 – 18 mm | 180.709 | — | 170.669 | 1.30.0512 | 1.20.0472 |
| DIN 471 – 19 mm | 190.748 | — | 180.709 | 1.30.0512 | 1.20.0472 |
| DIN 471 – 20 mm | 200.787 | — | 190.748 | 1.30.0512 | 1.20.0472 |
| DIN 471 – 21 mm | 210.827 | — | 200.787 | 1.30.0512 | 1.20.0472 |
| DIN 471 – 22 mm | 220.866 | — | 210.827 | 1.30.0512 | 1.20.0472 |
| DIN 471 – 24 mm | 240.945 | — | 22.90.902 | 1.30.0512 | 1.20.0472 |
| DIN 471 – 25 mm | 250.984 | — | 23.90.941 | 1.30.0512 | 1.20.0472 |
| DIN 471 – 26 mm | 261.024 | — | 24.90.980 | 1.30.0512 | 1.20.0472 |
| DIN 471 – 28 mm | 281.102 | — | 26.61.047 | 1.60.0630 | 1.50.0591 |
| DIN 471 – 29 mm | 291.142 | — | 27.61.087 | 1.60.0630 | 1.50.0591 |
| DIN 471 – 30 mm | 301.181 | — | 28.61.126 | 1.60.0630 | 1.50.0591 |
| DIN 471 – 32 mm | 321.260 | — | 30.31.193 | 1.60.0630 | 1.50.0591 |
| DIN 471 – 34 mm | 341.339 | — | 32.31.272 | 1.60.0630 | 1.50.0591 |
| DIN 471 – 35 mm | 351.378 | — | 331.299 | 1.60.0630 | 1.50.0591 |
| DIN 471 – 36 mm | 361.417 | — | 341.339 | 1.850.0728 | 1.750.0689 |
| DIN 471 – 38 mm | 381.496 | — | 361.417 | 1.850.0728 | 1.750.0689 |
| DIN 471 – 40 mm | 401.575 | — | 37.51.476 | 1.850.0728 | 1.750.0689 |
| DIN 471 – 42 mm | 421.654 | — | 39.51.555 | 1.850.0728 | 1.750.0689 |
| DIN 471 – 45 mm | 451.772 | — | 42.51.673 | 1.850.0728 | 1.750.0689 |
| DIN 471 – 48 mm | 481.890 | — | 45.51.791 | 1.850.0728 | 1.750.0689 |
| DIN 471 – 50 mm | 501.969 | — | 471.850 | 2.150.0846 | 20.0787 |
| DIN 471 – 52 mm | 522.047 | — | 491.929 | 2.150.0846 | 20.0787 |
| DIN 471 – 55 mm | 552.165 | — | 522.047 | 2.150.0846 | 20.0787 |
| DIN 471 – 56 mm | 562.205 | — | 532.087 | 2.150.0846 | 20.0787 |
| DIN 471 – 58 mm | 582.283 | — | 552.165 | 2.150.0846 | 20.0787 |
| DIN 471 – 60 mm | 602.362 | — | 572.244 | 2.150.0846 | 20.0787 |
| DIN 471 – 62 mm | 622.441 | — | 592.323 | 2.150.0846 | 20.0787 |
| DIN 471 – 63 mm | 632.480 | — | 602.362 | 2.150.0846 | 20.0787 |
| DIN 471 – 65 mm | 652.559 | — | 622.441 | 2.650.1043 | 2.50.0984 |
| DIN 471 – 68 mm | 682.677 | — | 652.559 | 2.650.1043 | 2.50.0984 |
| DIN 471 – 70 mm | 702.756 | — | 672.638 | 2.650.1043 | 2.50.0984 |
| DIN 471 – 72 mm | 722.835 | — | 692.717 | 2.650.1043 | 2.50.0984 |
| DIN 471 – 75 mm | 752.953 | — | 722.835 | 2.650.1043 | 2.50.0984 |
| DIN 471 – 78 mm | 783.071 | — | 752.953 | 2.650.1043 | 2.50.0984 |
| DIN 471 – 80 mm | 803.150 | — | 76.53.012 | 2.650.1043 | 2.50.0984 |
| DIN 471 – 82 mm | 823.228 | — | 78.53.091 | 2.650.1043 | 2.50.0984 |
| DIN 471 – 85 mm | 853.346 | — | 81.53.209 | 3.150.1240 | 30.1181 |
| DIN 471 – 88 mm | 883.465 | — | 84.53.327 | 3.150.1240 | 30.1181 |
| DIN 471 – 90 mm | 903.543 | — | 86.53.406 | 3.150.1240 | 30.1181 |
| DIN 471 – 95 mm | 953.740 | — | 91.53.602 | 3.150.1240 | 30.1181 |
| DIN 471 – 100 mm | 1003.937 | — | 96.53.799 | 3.150.1240 | 30.1181 |
| DIN 472: internal rings for bores | |||||
| DIN 472 – 8 mm | 80.315 | — | 8.40.331 | 0.90.0354 | 0.80.0315 |
| DIN 472 – 9 mm | 90.354 | — | 9.40.370 | 0.90.0354 | 0.80.0315 |
| DIN 472 – 10 mm | 100.394 | — | 10.40.409 | 1.10.0433 | 10.0394 |
| DIN 472 – 11 mm | 110.433 | — | 11.40.449 | 1.10.0433 | 10.0394 |
| DIN 472 – 12 mm | 120.472 | — | 12.50.492 | 1.10.0433 | 10.0394 |
| DIN 472 – 13 mm | 130.512 | — | 13.60.535 | 1.10.0433 | 10.0394 |
| DIN 472 – 14 mm | 140.551 | — | 14.60.575 | 1.10.0433 | 10.0394 |
| DIN 472 – 15 mm | 150.591 | — | 15.70.618 | 1.10.0433 | 10.0394 |
| DIN 472 – 16 mm | 160.630 | — | 16.80.661 | 1.10.0433 | 10.0394 |
| DIN 472 – 17 mm | 170.669 | — | 17.80.701 | 1.10.0433 | 10.0394 |
| DIN 472 – 18 mm | 180.709 | — | 190.748 | 1.10.0433 | 10.0394 |
| DIN 472 – 19 mm | 190.748 | — | 200.787 | 1.10.0433 | 10.0394 |
| DIN 472 – 20 mm | 200.787 | — | 210.827 | 1.10.0433 | 10.0394 |
| DIN 472 – 21 mm | 210.827 | — | 220.866 | 1.10.0433 | 10.0394 |
| DIN 472 – 22 mm | 220.866 | — | 230.906 | 1.10.0433 | 10.0394 |
| DIN 472 – 24 mm | 240.945 | — | 25.20.992 | 1.30.0512 | 1.20.0472 |
| DIN 472 – 25 mm | 250.984 | — | 26.21.031 | 1.30.0512 | 1.20.0472 |
| DIN 472 – 26 mm | 261.024 | — | 27.21.071 | 1.30.0512 | 1.20.0472 |
| DIN 472 – 28 mm | 281.102 | — | 29.41.157 | 1.30.0512 | 1.20.0472 |
| DIN 472 – 30 mm | 301.181 | — | 31.41.236 | 1.30.0512 | 1.20.0472 |
| DIN 472 – 32 mm | 321.260 | — | 33.71.327 | 1.30.0512 | 1.20.0472 |
| DIN 472 – 34 mm | 341.339 | — | 35.71.406 | 1.60.0630 | 1.50.0591 |
| DIN 472 – 35 mm | 351.378 | — | 371.457 | 1.60.0630 | 1.50.0591 |
| DIN 472 – 36 mm | 361.417 | — | 381.496 | 1.60.0630 | 1.50.0591 |
| DIN 472 – 37 mm | 371.457 | — | 391.535 | 1.60.0630 | 1.50.0591 |
| DIN 472 – 38 mm | 381.496 | — | 401.575 | 1.60.0630 | 1.50.0591 |
| DIN 472 – 40 mm | 401.575 | — | 42.51.673 | 1.850.0728 | 1.750.0689 |
| DIN 472 – 42 mm | 421.654 | — | 44.51.752 | 1.850.0728 | 1.750.0689 |
| DIN 472 – 45 mm | 451.772 | — | 47.51.870 | 1.850.0728 | 1.750.0689 |
| DIN 472 – 47 mm | 471.850 | — | 49.51.949 | 1.850.0728 | 1.750.0689 |
| DIN 472 – 48 mm | 481.890 | — | 50.51.988 | 1.850.0728 | 1.750.0689 |
| DIN 472 – 50 mm | 501.969 | — | 532.087 | 2.150.0846 | 20.0787 |
| DIN 472 – 52 mm | 522.047 | — | 552.165 | 2.150.0846 | 20.0787 |
| DIN 472 – 55 mm | 552.165 | — | 582.283 | 2.150.0846 | 20.0787 |
| DIN 472 – 56 mm | 562.205 | — | 592.323 | 2.150.0846 | 20.0787 |
| DIN 472 – 58 mm | 582.283 | — | 612.402 | 2.150.0846 | 20.0787 |
| DIN 472 – 60 mm | 602.362 | — | 632.480 | 2.150.0846 | 20.0787 |
| DIN 472 – 62 mm | 622.441 | — | 652.559 | 2.150.0846 | 20.0787 |
| DIN 472 – 63 mm | 632.480 | — | 662.598 | 2.150.0846 | 20.0787 |
| DIN 472 – 65 mm | 652.559 | — | 682.677 | 2.650.1043 | 2.50.0984 |
| DIN 472 – 68 mm | 682.677 | — | 712.795 | 2.650.1043 | 2.50.0984 |
| DIN 472 – 70 mm | 702.756 | — | 732.874 | 2.650.1043 | 2.50.0984 |
| DIN 472 – 72 mm | 722.835 | — | 752.953 | 2.650.1043 | 2.50.0984 |
| DIN 472 – 75 mm | 752.953 | — | 783.071 | 2.650.1043 | 2.50.0984 |
| DIN 472 – 78 mm | 783.071 | — | 813.189 | 2.650.1043 | 2.50.0984 |
| DIN 472 – 80 mm | 803.150 | — | 83.53.287 | 2.650.1043 | 2.50.0984 |
| DIN 472 – 82 mm | 823.228 | — | 85.53.366 | 2.650.1043 | 2.50.0984 |
| DIN 472 – 85 mm | 853.346 | — | 88.53.484 | 3.150.1240 | 30.1181 |
| DIN 472 – 88 mm | 883.465 | — | 91.53.602 | 3.150.1240 | 30.1181 |
| DIN 472 – 90 mm | 903.543 | — | 93.53.681 | 3.150.1240 | 30.1181 |
| DIN 472 – 92 mm | 923.622 | — | 95.53.760 | 3.150.1240 | 30.1181 |
| DIN 472 – 95 mm | 953.740 | — | 98.53.878 | 3.150.1240 | 30.1181 |
| DIN 472 – 100 mm | 1003.937 | — | 103.54.075 | 3.150.1240 | 30.1181 |
| DIN 6799: E-clips (retaining washers) | |||||
| DIN 6799 – 1.2 | — | 1.4–20.055–0.079 | 1.20.047 | 0.340.0134 | 0.30.0118 |
| DIN 6799 – 1.5 | — | 2–2.50.079–0.098 | 1.50.059 | 0.440.0173 | 0.40.0157 |
| DIN 6799 – 1.9 | — | 2.5–30.098–0.118 | 1.90.075 | 0.540.0213 | 0.50.0197 |
| DIN 6799 – 2.3 | — | 3–40.118–0.157 | 2.30.091 | 0.640.0252 | 0.60.0236 |
| DIN 6799 – 3.2 | — | 4–50.157–0.197 | 3.20.126 | 0.640.0252 | 0.60.0236 |
| DIN 6799 – 4 | — | 5–70.197–0.276 | 40.157 | 0.740.0291 | 0.70.0276 |
| DIN 6799 – 5 | — | 6–80.236–0.315 | 50.197 | 0.740.0291 | 0.70.0276 |
| DIN 6799 – 6 | — | 7–90.276–0.354 | 60.236 | 0.740.0291 | 0.70.0276 |
| DIN 6799 – 7 | — | 8–110.315–0.433 | 70.276 | 0.940.0370 | 0.90.0354 |
| DIN 6799 – 8 | — | 9–120.354–0.472 | 80.315 | 1.050.0413 | 10.0394 |
| DIN 6799 – 9 | — | 10–140.394–0.551 | 90.354 | 1.150.0453 | 1.10.0433 |
| DIN 6799 – 10 | — | 11–150.433–0.591 | 100.394 | 1.250.0492 | 1.20.0472 |
| DIN 6799 – 12 | — | 13–180.512–0.709 | 120.472 | 1.350.0531 | 1.30.0512 |
| DIN 6799 – 15 | — | 16–240.630–0.945 | 150.591 | 1.550.0610 | 1.50.0591 |
| DIN 6799 – 19 | — | 20–310.787–1.220 | 190.748 | 1.80.0709 | 1.750.0689 |
| DIN 6799 – 24 | — | 25–380.984–1.496 | 240.945 | 2.050.0807 | 20.0787 |
| DIN 6799 – 30 | — | 32–421.260–1.654 | 301.181 | 2.550.1004 | 2.50.0984 |
No exact match. The nearest sizes:
How to read the chart and size a groove
d1 is the nominal shaft (DIN 471) or bore (DIN 472) diameter and names the ring: DIN 471 – 20 × 1.2 is the ring for a 20 mm shaft, 1.2 mm thick. d2 is the groove diameter to machine (the standard gives its tolerance, tighter for small sizes), m the minimum groove width (tolerance H13) and s the ring thickness.
Groove depth t = (d1 − d2) / 2 for shafts and (d2 − d1) / 2 for bores. The edge distance from the groove to the shaft end should be at least about 3 × t, or the ring can shear the edge off under axial load.
E-clips (DIN 6799) are named by the groove diameter, not the shaft: an E-clip size 5 sits in a 5 mm groove and suits shafts of 6 to 8 mm. They are pushed on radially, so no pliers are needed, but they carry much lower axial loads than DIN 471 rings.
About Retaining Rings
Circlips (snap rings, Seeger rings) hold bearings, gears and pins axially on a shaft or in a housing. The standard type in this chart covers most uses; DIN 471/472 also define a heavy type (thicker rings, deeper grooves) for high axial loads, which is not listed.
The groove decides how much load the joint takes. Make the groove to the chart, with a sharp corner on the load side, and put the part against the ring with as little chamfer or radius as possible. A bearing with a large chamfer pressing on the ring tilts it and roughly halves the load capacity.
External rings are fitted with circlip pliers that open the ring by its lug holes; internal rings with pliers that close it. Do not over-expand a ring when fitting it. A ring that has been opened beyond its working diameter loses its grip in the groove.
Inch retaining rings
Inch retaining rings (ANSI/ASME B27.7, Rotor Clip SH and HO series) are sized by inch shaft diameters and use different groove tables. A metric 25 mm ring will not fit a 1 in (25.4 mm) shaft groove correctly; use the matching series.
Questions
What groove size for a 10 mm circlip?
For a DIN 471 ring on a 10 mm shaft: groove 9.6 mm diameter, 1.1 mm wide; ring 1 mm thick. For a DIN 472 ring in a 10 mm bore: groove 10.4 mm, 1.1 mm wide.
What is the difference between DIN 471 and DIN 472?
DIN 471 rings are external: they sit in a groove on a shaft. DIN 472 rings are internal: they sit in a groove in a bore. Both are sized by the shaft or bore diameter.
How deep is a circlip groove?
Half the difference between shaft and groove diameter. For a 30 mm shaft (groove 28.6 mm) that is 0.7 mm; for a 30 mm bore (groove 31.4 mm) also 0.7 mm.
What size E-clip for a 6 mm shaft?
DIN 6799 size 5 (groove 5 mm, shafts 6–8 mm) or size 4 (groove 4 mm, shafts 5–7 mm). E-clips are named by the groove diameter.
Sources
- DIN 471:2011, Retaining rings for shafts, normal type and heavy type
- DIN 472:2011, Retaining rings for bores, normal type and heavy type
- DIN 6799:2017, Retaining washers for shafts (E-rings)
- Westfield Fasteners: External circlips DIN 471 table
- Westfield Fasteners: E-clips DIN 6799 table
- AmesWeb: Internal circlip dimensions for bores (DIN 472)
- Würth: Circlips DIN 471, product data
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.