Drive Form Factors: 3.5", 2.5", M.2, mSATA, U.2 and EDSFF Sizes

Drive form factors fix the outside envelope so a drive fits its bay or slot. A 3.5-inch drive is 101.6 × 147 × 26.1 mm, a 2.5-inch drive 69.85 × 100.45 mm at 7, 9.5 or 15 mm high, and an M.2 SSD is always 22 mm wide. The type number gives width and length, so M.2 2280 is 22 × 80 mm.

17 sizesChecked 2026-11-156 sources
Bay drives (top view)3.5″2.5″1.8″M.2 (22 mm wide)223022422260228022110
3.5", 2.5" and 1.8" drives overlaid at one corner, next to the five M.2 lengths.Drawn to scale

Size chartTap a size for its drawing and full specs

17 of 17
Form factorWWidthmminLLengthmminHHeight (max.)mminHeight / thickness optionsInterface
Bay drives (3.5", 2.5", 1.8", U.2)
3.5-inch drive101.64.00146.995.7926.11.03—SATA, SAS
2.5-inch drive, 7 mm69.852.75100.453.9570.28—SATA
2.5-inch drive, 9.5 mm69.852.75100.453.959.50.37—SATA
2.5-inch drive, 15 mm69.852.75100.453.95150.59—SATA, SAS, U.2 NVMe
U.2 (2.5-inch NVMe)69.852.75100.453.95150.597 or 15 mmNVMe (PCIe ×4) via SFF-8639
1.8-inch drive542.1378.53.0980.315 or 8 mmPATA (ZIF/LIF), SATA (micro SATA)
Cards (M.2 and mSATA)
M.2 2230220.87301.18——PCIe NVMe (M key)
M.2 2242220.87421.65——SATA or PCIe NVMe (B+M or M key)
M.2 2260220.87602.36——SATA or PCIe NVMe
M.2 2280220.87803.15——PCIe NVMe (M key) or SATA (B+M key)
M.2 22110220.871104.33——PCIe NVMe (M key)
mSATA (full size)29.851.1850.82.00——SATA
mSATA half size29.851.1826.81.06——SATA
Data-centre SSDs (EDSFF)
EDSFF E1.S31.51.24111.494.39—5.9, 8.01, 9.5, 15 or 25 mmPCIe NVMe
EDSFF E1.L38.41.51318.7512.55—9.5 or 18 mmPCIe NVMe
EDSFF E3.S762.99112.754.44—7.5 mm (1T) or 16.8 mm (2T)PCIe NVMe, CXL
EDSFF E3.L762.99142.25.60—7.5 mm (1T) or 16.8 mm (2T)PCIe NVMe, CXL

How to read M.2 sizes and keys

An M.2 size code is width and length in millimetres run together: 2280 = 22 mm wide, 80 mm long; 2242 = 22 × 42 mm; 22110 = 22 × 110 mm. Laptops and motherboards list the lengths their M.2 slot supports; the slot has a standoff or latch at 30, 42, 60, 80 or 110 mm. A shorter drive can go in a longer slot only if there is a standoff position for it.

The key is the notch in the edge connector. M key carries up to four PCIe lanes and is used by NVMe SSDs. B key carries SATA or two PCIe lanes. B+M drives have both notches and fit both kinds of socket, but they are almost always SATA. An M-key socket does not necessarily accept SATA, so check the board manual for which protocols each slot supports.

Thickness depends on whether there are chips on one or both sides. The M.2 board is 0.8 mm thick; single-sided modules carry up to 1.5 mm of components on top (about 2.3 mm overall), double-sided modules add up to 1.35 mm underneath (about 3.5 mm overall). Thin laptops often accept single-sided drives only.

About Drive Form Factors

3.5-inch and 2.5-inch are named after the size of the disk platters that early drives used, not after any outside dimension. The cases are defined by the SFF-8301 and SFF-8201 specifications, including the side and bottom screw holes, so drives from any maker fit standard trays and cages. A 2.5-inch drive fits a 3.5-inch bay with an adapter tray.

2.5-inch drives come in several heights. 7 mm is the norm for SATA SSDs and thin laptop drives, 9.5 mm for most laptop hard drives, and 15 mm for enterprise SSDs and high-capacity hard drives, including U.2 NVMe SSDs, which use the 2.5-inch case with an SFF-8639 connector. A 9.5 mm laptop bay takes a 7 mm drive (often with a spacer), but not a 15 mm one.

M.2 replaced mSATA in laptops around 2014. mSATA cards are 29.85 mm wide and 50.8 mm long (half size: 26.8 mm), carry SATA only and use a mini-PCIe-shaped socket; they do not fit M.2 slots. In data centres the EDSFF family (E1.S, E1.L, E3.S, E3.L) is replacing both U.2 and M.2 with hot-swappable drives in standard thicknesses.

Which M.2 length do I need?

Desktop motherboards almost all take 2280, some also 22110 on one slot, and most still accept 2242 and 2260 through extra standoff holes. Handheld PCs and some thin laptops use 2230; a few laptops and mini PCs use 2242. A 2280 drive does not fit a 2230 slot. Adapters that extend a 2230 drive to 2280 length exist, but nothing makes a longer drive fit a shorter slot.

EDSFF thicknesses

EDSFF drives are defined with fixed thickness options so that cooling is predictable: E1.S at 5.9 mm (bare), 8.01 mm, 9.5 mm, 15 mm and 25 mm (with heatsinks), E1.L at 9.5 and 18 mm, and E3 at 7.5 mm (1T) and 16.8 mm (2T). E1 drives stand vertically in 1U servers; E3 drives suit 2U servers and also carry CXL memory and accelerator devices.

Questions

What does 2280 mean on an M.2 SSD?

It is the size: 22 mm wide and 80 mm long. 2230 is 22 × 30 mm, 2242 is 22 × 42 mm, 2260 is 22 × 60 mm and 22110 is 22 × 110 mm.

What are the dimensions of a 2.5-inch SSD?

69.85 mm wide and 100.45 mm long (2.75 × 3.95 in), and usually 7 mm high. Hard drives in the same format are 9.5 or 15 mm high.

How big is a 3.5-inch hard drive?

101.6 × 146.99 × 26.1 mm (4.0 × 5.79 × 1.03 in) maximum, per SFF-8301. That is why it is called 3.5-inch: the platters are 3.5 in across, not the case.

Can I put an M.2 2242 SSD in a 2280 slot?

Yes, if the board has a mounting hole or latch at 42 mm; most desktop boards do. Otherwise use an extender bracket. A 2280 drive cannot go into a slot that only has room for 2242.

Is mSATA the same as M.2?

No. mSATA is 29.85 × 50.8 mm, SATA only, with a different socket. M.2 is 22 mm wide in several lengths and supports SATA or PCIe NVMe. An mSATA drive needs an adapter to work in an M.2 or 2.5-inch bay.

How thick is an M.2 SSD?

The board is 0.8 mm. Single-sided drives are about 2.3 mm thick (0.8 mm PCB + 1.5 mm components); double-sided drives about 3.5 mm. Heatsinks add more; thin laptops often need a single-sided drive without a heatsink.

Sources

  1. SNIA SFF-8301: Form factor of 3.5" disk drives
  2. SNIA SFF-8201: Form factor of 2.5" disk drives (Rev 3.4)
  3. PCI-SIG: PCI Express M.2 Specification (card sizes, component height classes S1–S3, D1–D5)
  4. Thomas-Krenn wiki: M.2 module sizes and thickness (0.8 mm PCB, S3 = 2.3 mm, D2 = 3.5 mm)
  5. JEDEC MO-300: mSATA outline (50.8 × 29.85 mm; MO-300B half size)
  6. SNIA: EDSFF overview (SFF-TA-1006 E1.S, SFF-TA-1007 E1.L, SFF-TA-1008 E3)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.