ISO 2768 General Tolerances: Linear, Angular and Geometric

A drawing note such as ISO 2768-mK sets the tolerance of every dimension that has none of its own. The letter m (medium) gives, for example, ±0.2 mm on a 25 mm length and ±0.3 mm on 100 mm; the second letter K sets general flatness, perpendicularity, symmetry and run-out.

8 size rangesChecked 2026-11-155 sources
0.533040040000.050.10.20.5125Nominal size, mm± mmfmcv
Permissible deviation (±) for linear sizes in the four ISO 2768-1 classes. Each class roughly doubles the previous one; within a class the tolerance grows with the size range.Proportions shown, not to scale

Size chartSort by any column, or filter to find a row

8 of 8
Nominal sizefFine ±mminmMedium ±mmincCoarse ±mminvVery coarse ±mmin
0.5 to 3 mm0.050.00200.10.00390.20.0079—
over 3 to 6 mm0.050.00200.10.00390.30.01180.50.0197
over 6 to 30 mm0.10.00390.20.00790.50.019710.0394
over 30 to 120 mm0.150.00590.30.01180.80.03151.50.0591
over 120 to 400 mm0.20.00790.50.01971.20.04722.50.0984
over 400 to 1000 mm0.30.01180.80.031520.078740.1575
over 1000 to 2000 mm0.50.01971.20.047230.118160.2362
over 2000 to 4000 mm—20.078740.157580.3150

How to read the general-tolerance note

The note in or near the title block names the standard and the classes: ISO 2768-m (linear and angular only), ISO 2768-mK (plus geometrical class K) or ISO 2768-mH-E (the E adds the envelope requirement to all single features of size).

First letter, ISO 2768-1: f fine, m medium, c coarse, v very coarse. It applies to linear sizes (lengths, diameters, distances, external radii, chamfer heights) and to angles. Find the range that contains the nominal dimension and read the ± value.

Second letter, ISO 2768-2: H, K or L for straightness, flatness, perpendicularity, symmetry and circular run-out of features that have no geometric tolerance of their own. Roundness and parallelism are limited by the size tolerance; cylindricity, profile and position are not covered.

The general tolerance is a limit, not a target. A part outside it is rejected only if its function is impaired (ISO 2768-1 clause 5), but most purchase contracts treat it as a hard limit, so agree on that with your supplier.

About General Tolerances

General tolerances exist so that the drawing shows only the tolerances that matter. Choose the class to match the normal accuracy of the workshop: m is the usual choice for machined parts, f for precision work, c for welded and flame-cut parts, v for rough fabrication. Any dimension that needs a tighter (or looser) limit gets its own tolerance or a fit such as H7.

The linear values do not apply to dimensions with an individual tolerance, to auxiliary dimensions in brackets, to theoretically exact dimensions in boxes, or to angles of 90° that are implied but not dimensioned (those fall under the perpendicularity of ISO 2768-2).

For broken edges (external radii and chamfer heights) and for angles the standard has separate tables, shown below and in the calculator. Angular tolerances depend on the length of the shorter leg of the angle, because a long leg turns the same angular error into a larger displacement.

ISO 2768-2 was withdrawn in 2021 and replaced by ISO 22081, which works with an explicit general geometrical specification on the drawing instead of fixed classes. Drawings referencing ISO 2768-mK remain valid and are still produced daily; ISO 2768-1 itself remains in use.

Broken edges: external radii and chamfer heights (ISO 2768-1 Table 2)

Permissible deviations in mm. Sizes below 0.5 mm are toleranced individually.

Class0.5 to 3
f fine, m medium±0.2
c coarse, v very coarse±0.4

Angular dimensions (ISO 2768-1 Table 3)

By length of the shorter leg of the angle, in mm.

Classup to 10
f, m±1°
c±1°30′
v±3°

Questions

What does ISO 2768-mK mean?

Class m (medium) for untoleranced lengths and angles from ISO 2768-1 and class K for untoleranced geometry from ISO 2768-2.

What is the ISO 2768-m tolerance for 100 mm?

±0.3 mm (range over 30 to 120 mm). For 10 mm it is ±0.2 mm, for 150 mm ±0.5 mm, for 500 mm ±0.8 mm.

Does ISO 2768 apply to hole diameters?

Yes, to any untoleranced diameter: a Ø12 hole in class m is 11.8–12.2 mm. Holes for fits, threads and bearings need their own tolerance (H7, 6H …).

Is ISO 2768 still valid?

ISO 2768-1 is still in use. ISO 2768-2 (H, K, L) was withdrawn in 2021 in favour of ISO 22081, but drawings citing ISO 2768-mK remain valid and are still common.

Sources

  1. ISO 2768-1:1989, General tolerances, Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
  2. ISO 2768-2:1989, General tolerances, Part 2: Geometrical tolerances for features without individual tolerance indications (withdrawn)
  3. ISO 22081:2021, General geometrical specifications and general size specifications (successor of ISO 2768-2)
  4. Camcut: General tolerances for linear dimensions (ISO 2768-1 table)
  5. Star Rapid: General tolerances DIN ISO 2768 (PDF)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.