Surface Roughness Chart: Ra, µin and N Grades

Ra is the arithmetic mean deviation of the profile from its mean line. On metric drawings it is given in micrometres (Ra 1.6), on US drawings in microinches (63 µin), and on older drawings as a grade number: N7 = Ra 1.6 µm = 63 µin. Each N step doubles the roughness.

12 gradesChecked 2026-11-154 sources

Size chartSort by any column, or filter to find a row

12 of 12
GradeRaRoughness averageµmRaRoughness average (µin)λcCut-offmmlnEvaluation lengthmmTypical finish
N10.02510.251.3Superfinished, lapped gauge faces, optical parts
N20.0520.251.3Lapped or superfinished: gauge blocks, high-precision bearing races
N30.140.251.3Fine lapping, honing, polishing: valve seats, hydraulic piston rods
N40.280.84Honed or fine ground: cylinder bores, bearing journals
N50.4160.84Ground: shafts in plain bearings, seal running surfaces
N60.8320.84Fine turned or ground: bearing seats, gear flanks, O-ring grooves
N71.6630.84Good machined finish: fits, mating faces, bores for pins
N83.21252.512.5Standard machined finish: general turning and milling
N96.32502.512.5Rough machined: non-mating surfaces, clearance faces
N1012.5500840Rough turned or milled, coarse saw cuts
N11251000840Very rough machining, castings and forgings as delivered
N12502000840Flame cut, sand cast, hot rolled surfaces

How to read the roughness symbol

The basic symbol is a check mark (√) standing on the surface or on a leader. A horizontal bar across its top means material removal is required (machined); a small circle in the vee means material removal is not permitted (leave the surface as cast, forged or rolled). The plain check mark means any process is allowed.

The requirement is written above the long leg: Ra 1.6 means the mean roughness must not exceed 1.6 µm (under the 16 % rule of ISO 4288, up to 16 % of the measured values may exceed it). Ra max 1.6 invokes the max rule: no value may exceed it. Two lines, such as Ra 3.2 over Ra 0.8, give an upper and lower limit (U / L).

Further positions give the process ("ground"), the lay direction (=, ⊥, X, M, C, R, P) and the machining allowance. A circle at the corner of the symbol means the requirement applies all around the outline in that view.

US drawings (ASME Y14.36) use the same symbol with the value in microinches and no "Ra" prefix: a check mark with 63 means Ra 63 µin = 1.6 µm. Older European drawings show grade numbers (N7) or triangles from DIN 3141; convert both to Ra before quoting.

About Surface Roughness

Roughness costs money: each step finer usually needs another operation (turn → grind → hone → lap). Specify the coarsest finish that does the job. For most machined parts that is Ra 3.2 µm (125 µin); fits and seal surfaces need Ra 0.8–1.6; Ra 0.4 and below means grinding or better.

Ra averages the profile, so very different surfaces can have the same Ra. Rz (mean of the five highest peak-to-valley heights in five sampling lengths) reacts to single scratches and is preferred in Germany and for sealing faces. There is no fixed conversion: for turned and ground surfaces Rz is typically 4 to 7 times Ra, so Ra 1.6 roughly corresponds to Rz 6.3–10. Specify the parameter you need rather than converting.

Roughness is measured with a stylus instrument over the evaluation length (normally five cut-off lengths λc), perpendicular to the lay. The cut-off filter separates roughness from waviness; the table gives the standard cut-off for each Ra range. Comparator plates are fine for shop checks of turned or milled surfaces against N8–N10, but not for acceptance of tight values.

ISO 21920-1, -2 and -3 (2021) replaced ISO 1302, ISO 4287 and ISO 4288. The symbol and Ra/Rz parameters are unchanged in principle, but some defaults and the notation of the evaluation length changed; when a drawing references the older standards, measure to those.

Ra, Rz and Rmax in practice

Common drawing callouts and what they usually mean in the shop:

CalloutRa µmRa µinTypical process
Ra 12.5 / N1012.5500Rough turning, sawing
Ra 6.3 / N96.3250Rough milling, drilling
Ra 3.2 / N83.2125Standard turning and milling
Ra 1.6 / N71.663Finish turning, reaming, fine milling
Ra 0.8 / N60.832Fine turning, grinding
Ra 0.4 / N50.416Grinding
Ra 0.2 / N40.28Fine grinding, honing
Ra 0.1 / N30.14Lapping, polishing, superfinishing

Questions

What is Ra 3.2 in microinches?

Ra 3.2 µm ≈ 125 µin (grade N8). Ra 1.6 µm ≈ 63 µin (N7), Ra 0.8 µm ≈ 32 µin (N6). Multiply µm by 39.37 for µin.

What does N7 surface finish mean?

N7 is the ISO roughness grade for Ra 1.6 µm (63 µin): a good machined finish from finish turning, reaming or fine milling.

How do I convert Ra to Rz?

Only roughly: for machined surfaces Rz is usually 4–7 × Ra (Ra 0.8 ≈ Rz 3–6). The ratio depends on the process, so if the drawing asks for Rz, measure Rz.

Which cut-off length should I use for Ra 1.6?

0.8 mm (0.03 in), with an evaluation length of 4 mm. For Ra above 2 to 10 µm use 2.5 mm; for Ra above 0.02 to 0.1 µm use 0.25 mm (ISO 4288 / ISO 21920-3, non-periodic profiles).

Sources

  1. ISO 1302:2002, Indication of surface texture in technical product documentation (withdrawn, replaced by ISO 21920-1:2021)
  2. ISO 21920-1:2021, Surface texture: Profile, Part 1: Indication of surface texture
  3. ISO 4288:1996, Rules and procedures for the assessment of surface texture (cut-off by Ra range; replaced by ISO 21920-3:2021)
  4. ASME B46.1-2019: Surface Texture (Surface Roughness, Waviness, and Lay)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.