Hose Clamp Size Chart (SAE Worm-Drive Sizes)
The SAE size number of a worm-drive hose clamp tells you its largest diameter: from #8 up, the clamp opens to (size + 8) ÷ 16 inches. A #24 clamp opens to 2 in (51 mm) and closes to about 1-1/16 in (27 mm). Measure the outside of the hose on the barb, then pick a size with that diameter in the middle of its range.
Size chartRanges are typical; makers differ by about 1/16 in at the small end
| SAE size | Minimum diametermmin | Maximum diametermmin | Band width |
|---|---|---|---|
| #4 | 67/32 | 165/8 | 5/16 in (8 mm) miniature |
| #6 | 103/8 | 227/8 | 5/16 in (8 mm) miniature |
| #8 | 117/16 | 251 | 1/2 in (12.7 mm) |
| #10 | 131/2 | 291 1/8 | 1/2 in (12.7 mm) |
| #12 | 149/16 | 321 1/4 | 1/2 in (12.7 mm) |
| #16 | 1711/16 | 381 1/2 | 1/2 in (12.7 mm) |
| #20 | 193/4 | 441 3/4 | 1/2 in (12.7 mm) |
| #24 | 271 1/16 | 512 | 1/2 in (12.7 mm) |
| #28 | 331 5/16 | 572 1/4 | 1/2 in (12.7 mm) |
| #32 | 401 9/16 | 642 1/2 | 1/2 in (12.7 mm) |
| #36 | 461 13/16 | 702 3/4 | 1/2 in (12.7 mm) |
| #40 | 522 1/16 | 763 | 1/2 in (12.7 mm) |
| #44 | 592 5/16 | 833 1/4 | 1/2 in (12.7 mm) |
| #48 | 652 9/16 | 893 1/2 | 1/2 in (12.7 mm) |
| #52 | 712 13/16 | 953 3/4 | 1/2 in (12.7 mm) |
| #56 | 783 1/16 | 1024 | 1/2 in (12.7 mm) |
| #64 | 903 9/16 | 1144 1/2 | 1/2 in (12.7 mm) |
| #72 | 1034 1/16 | 1275 | 1/2 in (12.7 mm) |
| #80 | 1164 9/16 | 1405 1/2 | 1/2 in (12.7 mm) |
| #88 | 1295 1/16 | 1526 | 1/2 in (12.7 mm) |
| #96 | 1415 9/16 | 1656 1/2 | 1/2 in (12.7 mm) |
| #104 | 1546 1/16 | 1787 | 1/2 in (12.7 mm) |
No exact match. The nearest sizes:
How to choose the clamp size
Measure the hose OD where the clamp will sit: on the barb or spigot, not on the free hose, because the hose stretches over the fitting. A 1 in ID heater hose on a 1 in spigot typically measures about 1-3/8 to 1-1/2 in (35–38 mm) outside.
Pick a size whose range puts that diameter in the middle. Near the top of the range the band barely engages the screw; near the bottom the loose tail sticks out and can snag. For 1-1/2 in (38 mm), #20 (3/4–1-3/4 in) and #24 (1-1/16–2 in) both fit; #24 centres better.
The SAE number is the same across US makers for the maximum diameter. Metric (DIN 3017 / "Jubilee" style) clamps are sold by range in millimetres instead (for example 25–40 mm or 32–50 mm), with a 9 mm or 12 mm band.
About Hose Clamps
A worm-drive clamp is a perforated or embossed steel band with a screw housing. US standard clamps have a 1/2 in (12.7 mm) band and a 5/16 in hex screw (about 8 mm), tightened to roughly 30–35 lbf·in (3.5–4 N·m) on a rubber hose; small #4 and #6 clamps are usually miniature 5/16 in (8 mm) band clamps with a 1/4 in (7 mm) hex. European DIN 3017 clamps use 9 mm (light, automotive) and 12 mm bands.
Perforated bands (the slots go right through) are cheaper but can cut into soft silicone hose; non-perforated, embossed bands ("lined" or "smooth underside") protect silicone and thin-walled hose. Stainless band with a plated screw (often marked W2) is fine indoors; marine and exhaust-side use need all-stainless W4/W5 (304/316) clamps.
Worm-drive clamps suit hose up to about 30 psi (2 bar) on barbed fittings: coolant, fuel return, intake and drain lines. For pressurised hydraulic hose use crimped fittings (hose sizes); for fuel injection hose use clamps rated for it (fuel injection or T-bolt clamps).
Metric DIN 3017 clamp ranges
Typical ranges sold for 9 mm and 12 mm band worm-drive clamps. Exact ranges differ slightly by maker; the nearest SAE size is the one that covers the same diameters best.
| Range (mm) | Band | Nearest SAE size |
|---|---|---|
| 8–12 | 9 mm | #4 |
| 10–16 | 9 mm | #6 |
| 12–22 | 9 mm | #8, #10 |
| 16–27 | 9 / 12 mm | #12 |
| 20–32 | 9 / 12 mm | #16 |
| 25–40 | 9 / 12 mm | #20 |
| 32–50 | 12 mm | #24, #28 |
| 40–60 | 12 mm | #32, #36 |
| 50–70 | 12 mm | #40 |
| 60–80 | 12 mm | #44, #48 |
| 70–90 | 12 mm | #52 |
| 80–100 | 12 mm | #56 |
| 90–110 | 12 mm | #64 |
| 100–120 | 12 mm | #72 |
Questions
What size hose clamp for 1 inch hose?
For 1 in ID hose on a 1 in barb, the outside is usually about 1-3/8 to 1-1/2 in (35–38 mm). A #20 (3/4–1-3/4 in) or #24 (1-1/16–2 in) clamp fits; measure the OD to choose. For 1 in OD tubing use #16 (11/16–1-1/2 in).
What does the number on a hose clamp mean?
The SAE size number. From #8 upward the maximum diameter is (size + 8) ÷ 16 in: #12 opens to 1-1/4 in, #16 to 1-1/2 in, #32 to 2-1/2 in, #40 to 3 in. The minimum is roughly 1 in smaller for the larger sizes.
What size is a #10 hose clamp?
About 1/2 to 1-1/8 in (13–29 mm) clamping range with a 1/2 in band. Common for 1/2 in heater hose and 5/8 in fuel or vacuum hose on barbs.
How tight should a worm-drive hose clamp be?
About 30–35 lbf·in (3.5–4 N·m) for standard 1/2 in band clamps on rubber hose, and around 10–15 lbf·in (1–1.7 N·m) for miniature clamps. Overtightening cuts the hose and strips the band; re-check after the first heat cycle.
What is the band width of a DIN 3017 clamp?
9 mm or 12 mm. The 9 mm band is the common automotive and small-hose size; 12 mm is used from about 20 mm diameter upward. US SAE clamps have a 1/2 in (12.7 mm) band, miniature clamps 5/16 in (8 mm).
Sources
- SAE J1508: Hose Clamp Specifications (worm-drive type F size numbers)
- DIN 3017-1: Hose clamps with worm drive (metric, 9 and 12 mm band)
- Ideal Tridon: worm-drive clamp size charts
- Breeze Industrial Products: Aero-Seal / Power-Seal clamp size charts
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.