Pneumatic Tubing Size Chart (Metric & Inch)

Pneumatic tube is sized by outside diameter, because push-to-connect fittings grip the outside. A 6 mm tube fits only 6 mm fittings. A 1/4 in tube is 6.35 mm and will either not go in or blow out. The inside diameter depends on the material: 6 × 4 mm is the common polyurethane size.

13 sizesChecked 2026-11-154 sources
Metric (mm)468101216Inch (OD)1/85/323/161/45/163/81/210 mm
Metric and inch tube sections to one scale; metric tubes show the polyurethane bore. Close pairs such as 6 mm and 1/4 in look alike but do not share fittings.Drawn to scale

Size chartOrder tube by OD; ID varies with material

13 of 13
Tube ODODOutside diametermminmm · inID, polyurethane (typical)mminmm · inID, nylon (typical)mminmm · inCommon fitting threads
Metric tube (ISO 14743 push-in fittings)
4 mm40.1572.50.0982.50.098M5, G 1/8
6 mm60.23640.15740.157M5, G 1/8, G 1/4
8 mm80.31550.19760.236G 1/8, G 1/4, G 3/8
10 mm100.3946.50.2567.50.295G 1/4, G 3/8, G 1/2
12 mm120.47280.31590.354G 1/4, G 3/8, G 1/2
16 mm160.630100.394130.512G 3/8, G 1/2
Inch tube (fractional OD)
1/8″3.180.125——10-32 UNF, 1/8 NPT
5/32″3.970.156——10-32 UNF, 1/8 NPT
3/16″4.760.188——10-32 UNF, 1/8 NPT
1/4″6.350.250——1/8 NPT, 1/4 NPT
5/16″7.940.313——1/8 NPT, 1/4 NPT
3/8″9.530.375——1/4 NPT, 3/8 NPT
1/2″12.70.500——3/8 NPT, 1/2 NPT

How to read a tube size

Metric tube is written OD × ID in millimetres: 8 × 5 is 8 mm outside, 5 mm inside (polyurethane), 8 × 6 the thinner-walled nylon version. Catalogue part numbers often encode the same numbers: SMC TU0805 = 8 × 5 mm polyurethane.

Inch tube is named by OD only (1/4 in, 5/32 in). Measure the OD with a caliper: 4.0 mm vs 5/32 in (3.97 mm) is a 0.03 mm difference and the two are often used in each other's fittings, but 6 mm vs 1/4 in (6.35 mm), 10 mm vs 3/8 in (9.53 mm) and 12 mm vs 1/2 in (12.7 mm) are not interchangeable.

Push-to-connect fittings are named by tube OD and thread: a "6 mm × G 1/8" straight connector takes 6 mm tube and screws into a G 1/8 port; "1/4 × 1/8 NPT" takes 1/4 in tube into a 1/8 NPT port.

About Pneumatic Tubing

Polyurethane (PU) is flexible, kinks less and suits moving machine parts and short runs; typical maximum working pressure is around 10 bar (145 psi) at 20 °C, dropping with temperature. Nylon (PA) is stiffer, holds pressure better (often 15–30 bar depending on size) and has a larger bore for the same OD, so it is preferred for longer, fixed runs. Polyethylene is the cheap option for low-pressure and fluid lines. Always check the maker's pressure–temperature table.

Flow depends on the inside diameter. For the same 8 mm OD, nylon 8 × 6 has 44 % more bore area than polyurethane 8 × 5. A cylinder that moves slowly on 6 × 4 PU line often speeds up noticeably on 8 × 6 nylon.

Cut tube square with a tube cutter, not side cutters, and push it in past the O-ring until it hits the stop (about 15–20 mm for 6–10 mm tube). An angled or squashed cut is the usual cause of a leaking push-in joint. Soft tube (Shore 85A PU and softer) may need an insert for metal compression fittings, not for push-in fittings.

Questions

Is 1/4 inch air tubing the same as 6 mm?

No. 1/4 in is 6.35 mm OD, 0.35 mm bigger than 6 mm. A 1/4 in tube will not seat properly in a 6 mm push-in fitting, and 6 mm tube in a 1/4 in fitting can blow out under pressure. Use an adapter union (6 mm × 1/4 in).

What is the ID of 6 mm pneumatic tubing?

Usually 4 mm for both polyurethane and nylon (6 × 4). Some soft PU tubes are 6 × 4.3 or thicker-walled 6 × 3.5. Check the part number.

What thread does a 1/4 inch push-to-connect fitting have?

The tube size and the thread are independent. 1/4 in tube fittings are commonly made with 1/8 NPT or 1/4 NPT male threads, and also 10-32 UNF for small valves. Metric 6 mm fittings come with M5, G 1/8 or G 1/4.

Can I use 5/32 tube in a 4 mm fitting?

Usually yes: 5/32 in is 3.97 mm, within the OD tolerance of 4 mm tube, and many makers list them as interchangeable. Check the fitting maker's note; 5/16 in (7.94 mm) in 8 mm fittings is also common but not universally approved.

What size air line do I need?

For tools fed from a hose reel use hose, not tubing. For machine pneumatics, 4 mm feeds small cylinders up to about 16 mm bore, 6 mm up to 32 mm bore, 8 mm up to 50 mm bore and 10–12 mm larger cylinders or manifolds, at normal cycle rates. Long runs or fast cycles need the next size up.

Sources

  1. SMC: TU series polyurethane tubing and T series nylon tubing (catalogue part numbers OD × ID)
  2. Festo: PUN polyurethane tubing data sheet
  3. ISO 14743: Pneumatic fluid power: push-in connectors for thermoplastic tubes
  4. Parker Hannifin: Prestolok push-in fittings catalogue (tube OD vs thread offerings)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.