Steel Pipe Size Chart (NPS & DN, Schedule 40, 80, 160)

Outside diameter, wall thickness and inside diameter of steel pipe from NPS 1/8 to NPS 24, per ASME B36.10M and B36.19M. The outside diameter of a given NPS never changes. The schedule only changes the wall, so a heavier schedule means a smaller bore.

23 sizesChecked 2026-11-154 sources
1/2″21.3 mm0.840 in3/4″26.7 mm1.050 in1″33.4 mm1.315 in1-1/4″42.2 mm1.660 in1-1/2″48.3 mm1.900 in2″60.3 mm2.375 in2-1/2″73.0 mm2.875 in3″88.9 mm3.500 in4″114.3 mm4.500 in
Nominal size above each pipe, actual outside diameter below. Up to NPS 12 the OD is always larger than the name.Drawn to scale · Dimensions in mmDimensions in inches

Size chartTap a size for its drawing and full specs

23 of 23
SizeDN (metric nominal)ODOutside diametermmintWall, SCH 40mminIDInside diameter, SCH 40mmintWall, SCH 80mminIDInside diameter, SCH 80mmintWall, SCH 160mmintWall, XXSmminWeight, SCH 40kg/mlb/ft
NPS 1/8610.30.4051.730.0686.830.2692.410.0955.460.215——0.360.24
NPS 1/4813.70.5402.240.0889.250.3643.020.1197.670.302——0.640.43
NPS 3/81017.10.6752.310.09112.520.4933.200.12610.740.423——0.850.57
NPS 1/21521.30.8402.770.10915.800.6223.730.14713.870.5464.780.1887.470.2941.260.85
NPS 3/42026.71.0502.870.11320.930.8243.910.15418.850.7425.560.2197.820.3081.681.13
NPS 12533.41.3153.380.13326.641.0494.550.17924.310.9576.350.2509.090.3582.501.68
NPS 1-1/43242.21.6603.560.14035.051.3804.850.19132.461.2786.350.2509.700.3823.382.27
NPS 1-1/24048.31.9003.680.14540.891.6105.080.20038.101.5007.140.28110.160.4004.052.72
NPS 25060.32.3753.910.15452.502.0675.540.21849.251.9398.740.34411.070.4365.453.66
NPS 2-1/26573.02.8755.160.20362.712.4697.010.27659.002.3239.520.37514.020.5528.635.80
NPS 38088.93.5005.490.21677.933.0687.620.30073.662.90011.130.43815.240.60011.287.58
NPS 3-1/290101.64.0005.740.22690.123.5488.080.31885.453.364——13.579.12
NPS 4100114.34.5006.020.237102.264.0268.560.33797.183.82613.490.53117.120.67416.0710.80
NPS 5125141.35.5636.550.258128.195.0479.520.375122.254.81315.880.62519.050.75021.7714.63
NPS 6150168.36.6257.110.280154.056.06510.970.432146.335.76118.260.71921.950.86428.2618.99
NPS 8200219.18.6258.180.322202.727.98112.700.500193.677.62523.010.90622.220.87542.5328.58
NPS 10250273.110.7509.270.365254.5110.02015.090.594242.879.56228.581.12525.401.00060.3040.52
NPS 12300323.812.75010.310.406303.2311.93817.480.688288.9011.37433.321.31225.401.00079.7253.57
NPS 14350355.614.00011.130.438333.3513.12419.050.750317.5012.50035.711.406—94.5063.50
NPS 16400406.416.00012.700.500381.0015.00021.440.844363.5214.31240.491.594—123.2982.85
NPS 18450457.218.00014.270.562428.6516.87623.830.938409.5516.12445.241.781—155.90104.76
NPS 20500508.020.00015.090.594477.8218.81226.191.031455.6317.93850.011.969—183.39123.23
NPS 24600609.624.00017.480.688574.6522.62430.941.218547.7321.56459.542.344—255.15171.45

How to read a pipe size and schedule

A pipe size has two parts: the nominal pipe size (NPS) and the schedule. NPS 2 SCH 40 means a pipe with the NPS 2 outside diameter (2.375 in) and the Schedule 40 wall (0.154 in). The metric name for the same pipe is DN 50. DN is only a label and does not convert to the OD either.

From NPS 1/8 to NPS 12 the nominal size is roughly the inside diameter of old standard-weight pipe, so the OD is always larger than the name: a 1/2" pipe is 0.840 in outside, a 2" pipe 2.375 in. From NPS 14 up, the OD equals the nominal size: an NPS 16 pipe is exactly 16.000 in outside.

The schedule sets the wall. For one NPS, SCH 10S, 40, 80, 160 and XXS share the same OD and get progressively thicker walls and smaller bores. That is why fittings, flanges and clamps are sized by NPS alone: every schedule of the same NPS fits them.

STD, XS and XXS are the older weight classes (standard, extra strong, double extra strong). STD equals SCH 40 up to NPS 10 and XS equals SCH 80 up to NPS 8; above that they stay at 0.375 in and 0.500 in while the numbered schedules keep growing. Stainless pipe adds an S (10S, 40S, 80S) under B36.19M; 40S and 80S match SCH 40 and 80 up to NPS 10 and match STD and XS above.

About Pipe Sizes

This chart covers wrought steel pipe as made to ASME B36.10M (carbon and alloy steel, the dimensions behind ASTM A53, A106 and API 5L) and ASME B36.19M (stainless, schedules 5S and 10S). PVC and CPVC Schedule 40 and 80 pipe use the same outside diameters, so the OD column also identifies plastic pipe; their walls are close to but not always identical with steel.

To identify an unknown pipe, measure the outside diameter with a caliper or wrap a tape around it and divide the circumference by π. Match the OD to the chart: 1.315 in (33.4 mm) is NPS 1 whatever its wall. Then measure the wall at a cut end to find the schedule.

Inside diameter is OD minus twice the wall. It sets flow capacity: the bore of NPS 2 drops from 2.067 in in SCH 40 to 1.939 in in SCH 80, which is 12 % less flow area. The schedule picker below gives area, weight and water content for any combination.

Weights are for plain-end carbon steel calculated with the B36.10M formula W = 10.69 × (D − t) × t lb/ft. Charts based on older editions used 10.68 and show values up to 0.1 % lower (3.65 instead of 3.66 lb/ft for NPS 2 SCH 40). Stainless steel is about 2 % heavier; threaded-and-coupled pipe a few percent heavier again.

Metric pipe: DN and ISO outside diameters

In ISO 4200 / EN 10220 the common series uses the same outside diameters, rounded to 0.1 mm: 21.3 mm (DN 15), 26.9 (DN 20), 33.7 (DN 25), 42.4 (DN 32), 48.3 (DN 40), 60.3 (DN 50), 76.1 (DN 65), 88.9 (DN 80), 114.3 (DN 100), 168.3 (DN 150), 219.1 (DN 200). Note that DN 20, 25, 32 and 65 in the European series differ by about 0.2–3 mm from the ASME pipe (26.7, 33.4, 42.2, 73.0 mm), so fittings are not always interchangeable. The mm values in this chart are converted from the ASME inch dimensions.

Which schedule to use

Schedule 40 is the default for water, air and gas service at ordinary pressure. Schedule 80 is used for higher pressure, for threaded pipe that must keep enough wall below the thread root, and where corrosion allowance matters. SCH 160 and XXS are for high-pressure and high-temperature lines and small-bore instrument connections. Thin 5S and 10S stainless pipe is joined by welding or grooved couplings; the walls are too thin for NPT threads.

Questions

What is the actual outside diameter of a 2 inch pipe?

2.375 in (60.3 mm) in every schedule. Only the wall changes: 0.154 in in SCH 40 (ID 2.067 in) and 0.218 in in SCH 80 (ID 1.939 in).

What is the difference between Schedule 40 and Schedule 80?

Schedule 80 has a thicker wall on the same outside diameter, so it holds more pressure but has a smaller bore and weighs more. For NPS 1: SCH 40 wall 0.133 in, ID 1.049 in, 1.68 lb/ft; SCH 80 wall 0.179 in, ID 0.957 in, 2.17 lb/ft.

Is Schedule 40 the same as STD?

Up to NPS 10, yes. From NPS 12 the STD wall stays at 0.375 in while SCH 40 grows (0.406 in for NPS 12, 0.500 in for NPS 16). Likewise XS = SCH 80 only up to NPS 8.

What does DN mean, and what is DN 50 in inches?

DN (diamètre nominal) is the metric nominal size. DN 50 corresponds to NPS 2 (OD 60.3 mm / 2.375 in). DN is not a measurement: DN 15 = NPS 1/2 = 21.3 mm OD, DN 25 = NPS 1 = 33.4 mm OD.

Why is a 1/2 inch pipe bigger than 1/2 inch?

The nominal size dates from 19th-century wrought-iron pipe, when the name was close to the bore. Walls got thinner as materials improved, but the outside diameter was kept so threads and fittings stayed compatible. Today a 1/2" pipe is 0.840 in outside and 0.622 in inside (SCH 40).

Do PVC Schedule 40 and steel Schedule 40 pipe have the same size?

They share the same outside diameter for each NPS, so PVC and steel couplings measure the same. Wall thicknesses are close for small sizes but are set by different standards (ASTM D1785 for PVC), so check the ID if flow matters.

Sources

  1. ASME B36.10M: Welded and Seamless Wrought Steel Pipe
  2. ASME B36.19M: Stainless Steel Pipe
  3. Engineers Edge: Schedule 40 steel pipe sizes (ASME/ANSI B36.10/19)
  4. Project Materials: ASME B36.10 / B36.19 pipe dimension charts

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.