Hydraulic Hose Size Chart (Dash Sizes)
Hose dash size is the inside diameter in sixteenths of an inch: -8 hose has a 1/2 in (12.7 mm) bore, DN12 in metric catalogues. The pressure rating falls as the bore grows: a -4 two-wire 100R2AT hose is rated 5,000 psi, a -32 only 1,125 psi.
Size chartTap a size for its drawing and full specs
| Dash | Nominal ID | IDInside diametermmin | DN (metric) | SAE 100R1AT (1 wire braid)barpsi | SAE 100R2AT (2 wire braids)barpsi | SAE 100R12 (4 spiral)barpsi | SAE 100R13 (spiral)barpsi | EN 853 1SNbarpsi | EN 853 2SNbarpsi |
|---|---|---|---|---|---|---|---|---|---|
| -3 | 3/16" | 4.80.188 | DN5 | — | 3455000 | — | — | 2503626 | 4156019 |
| -4 | 1/4" | 6.40.250 | DN6 | 1902750 | 3455000 | — | — | 2253263 | 4005802 |
| -5 | 5/16" | 7.90.313 | DN8 | 1722500 | 2934250 | — | — | 2153118 | 3505076 |
| -6 | 3/8" | 9.50.375 | DN10 | 1552250 | 2764000 | 2764000 | — | 1802611 | 3304786 |
| -8 | 1/2" | 12.70.500 | DN12 | 1382000 | 2413500 | 2764000 | — | 1602321 | 2753989 |
| -10 | 5/8" | 15.90.625 | DN16 | 1031500 | 1902750 | 2764000 | — | 1301885 | 2503626 |
| -12 | 3/4" | 19.00.750 | DN19 | 861250 | 1552250 | 2764000 | 3455000 | 1051523 | 2153118 |
| -16 | 1" | 25.41.000 | DN25 | 691000 | 1382000 | 2764000 | 3455000 | 881276 | 1652393 |
| -20 | 1-1/4" | 31.81.250 | DN31 | 43625 | 1121625 | — | 3455000 | 63914 | 1251813 |
| -24 | 1-1/2" | 38.11.500 | DN38 | — | 861250 | — | 3455000 | 50725 | 901305 |
| -32 | 2" | 50.82.000 | DN51 | 26375 | 781125 | — | 3455000 | 40580 | 801160 |
No exact match. The nearest sizes:
How to read a hose size
The layline printed on the hose gives the type and size, for example SAE 100R2AT -8 1/2" 3500 PSI or EN 853 2SN DN12 275 bar. The dash number counts sixteenths of an inch of inside diameter: -4 = 4/16 = 1/4 in, -12 = 3/4 in, -16 = 1 in. DN is the same bore in millimetres, rounded (DN12 = 1/2 in = 12.7 mm).
Measure an unmarked hose at the bore, not the outside: the OD depends on the reinforcement and the brand, so two -8 hoses of different types can differ by several millimetres outside. Cut ends or the fitting's hose-end stamp are the reliable references.
Hose fittings use the same dash numbers but they refer to the hose bore on the hose end and to the tube OD on the thread end. A -8 hose with -8 JIC ends has 1/2 in ID and 3/4-16 threads (JIC -8). The working pressure of the assembly is the lower of hose and fitting rating.
About Hydraulic Hose Sizes
The pressures in the chart are the maximum working pressures of the SAE J517 and EN 853 types, as printed in hose makers' catalogues. Minimum burst pressure is four times the working pressure. Many brands rate their hose higher than the standard minimum; the layline of the hose in your hand is what counts.
100R1AT / 1SN has one high-tensile steel wire braid and suits return lines, pilot circuits and moderate-pressure work. 100R2AT / 2SN has two braids and is the general-purpose high-pressure hose. 100R12 (four spiral wire layers, 4,000 psi class) and 100R13 (5,000 psi class from -12 up) handle high pressure with surge loads on excavators and presses. The EN 853 1SN and 2SN are the compact versions of the older R1/R2 with a thinner cover; their ratings are slightly higher in the small sizes.
Size the bore for flow, not just pressure. Common velocity limits are about 2–4 ft/s (0.6–1.2 m/s) for suction lines, 7–15 ft/s (2–4.5 m/s) for return lines and 15–20 ft/s (4.5–6 m/s) for pressure lines. Bore in inches = √(0.321 × gpm ÷ ft/s): a 10 gpm (38 L/min) pressure line at 20 ft/s needs 0.40 in, so a -8 hose; a suction line at the same flow and 4 ft/s needs about 0.9 in, so -16.
Hose size, ID and DN at a glance
Dash size, nominal bore and the DN used in EN/ISO catalogues. Thermoplastic and suction hoses use the same numbering. Hose with a 1/8 in (-2) bore exists only as thermoplastic or specialty hose.
| Dash | ID (in) | ID (mm) | DN |
|---|---|---|---|
| -3 | 3/16 | 4.8 | DN5 |
| -4 | 1/4 | 6.4 | DN6 |
| -5 | 5/16 | 7.9 | DN8 |
| -6 | 3/8 | 9.5 | DN10 |
| -8 | 1/2 | 12.7 | DN12 |
| -10 | 5/8 | 15.9 | DN16 |
| -12 | 3/4 | 19.1 | DN19 |
| -16 | 1 | 25.4 | DN25 |
| -20 | 1-1/4 | 31.8 | DN31 |
| -24 | 1-1/2 | 38.1 | DN38 |
| -32 | 2 | 50.8 | DN51 |
Questions
What size is -8 hydraulic hose?
1/2 in (12.7 mm) inside diameter, DN12. Working pressure is 2,000 psi for 100R1AT, 3,500 psi for 100R2AT, 4,000 psi for 100R12; EN 853 2SN is rated 275 bar.
Is hose dash size the inside or outside diameter?
Inside diameter, in sixteenths of an inch. For tube and tube fittings the dash number is the outside diameter, which is why a -8 hose end and a -8 tube fitting share the 3/4-16 JIC thread but not the same bore.
What is the difference between R1 and R2 hose?
One wire braid versus two. At -8, 100R1AT is rated 2,000 psi and 100R2AT 3,500 psi; at -16, 1,000 psi versus 2,000 psi. They use the same fitting sizes in most crimp systems, but check the maker's fitting series, because some ferrules are specific to the hose type.
What does DN mean on hydraulic hose?
Diameter nominal, the bore in millimetres rounded: DN6 = 1/4 in (-4), DN10 = 3/8 in (-6), DN12 = 1/2 in (-8), DN19 = 3/4 in (-12), DN25 = 1 in (-16).
What is the burst pressure of hydraulic hose?
Four times the maximum working pressure for SAE J517 and EN 853 hose. A -8 100R2AT hose rated 3,500 psi has a minimum burst of 14,000 psi. Never use the burst figure for design.
Sources
- SAE J517: Hydraulic Hose (100R1, 100R2, 100R12, 100R13)
- EN 853: Rubber hoses and hose assemblies, wire braid reinforced hydraulic type (1SN, 2SN)
- Parker Hannifin: Catalog 4400 Hose, Fittings and Equipment (hose specifications)
- Gates: Hydraulics Master Catalog (hose working pressure tables)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.