Needle Roller Bearing Size Chart: HK and NA49
Needle roller bearings pack many thin rollers into a very small radial height. HK drawn cups are numbered by shaft size and width: HK1612 runs on a 16 mm shaft, is 22 mm outside and 12 mm wide. NA49xx bearings have a machined outer ring and an inner ring and share the bore code system of ball bearings.
Size chartTap a size for its drawing and full specs
| Bearing | FwRaceway diameter / shaft (Fw)mmin | dBore diametermmin | DOutside diametermmin | C/BWidth (C for HK, B for NA)mmin |
|---|---|---|---|---|
| HK: drawn cup, open ends | ||||
| HK0306 | 30.118 | — | 6.50.256 | 60.236 |
| HK0408 | 40.157 | — | 80.315 | 80.315 |
| HK0509 | 50.197 | — | 90.354 | 90.354 |
| HK0609 | 60.236 | — | 100.394 | 90.354 |
| HK0709 | 70.276 | — | 110.433 | 90.354 |
| HK0810 | 80.315 | — | 120.472 | 100.394 |
| HK1010 | 100.394 | — | 140.551 | 100.394 |
| HK1012 | 100.394 | — | 140.551 | 120.472 |
| HK1210 | 120.472 | — | 160.630 | 100.394 |
| HK1212 | 120.472 | — | 180.709 | 120.472 |
| HK1412 | 140.551 | — | 200.787 | 120.472 |
| HK1512 | 150.591 | — | 210.827 | 120.472 |
| HK1516 | 150.591 | — | 210.827 | 160.630 |
| HK1612 | 160.630 | — | 220.866 | 120.472 |
| HK1616 | 160.630 | — | 220.866 | 160.630 |
| HK2010 | 200.787 | — | 261.024 | 100.394 |
| HK2016 | 200.787 | — | 261.024 | 160.630 |
| HK2020 | 200.787 | — | 261.024 | 200.787 |
| HK2216 | 220.866 | — | 281.102 | 160.630 |
| HK2516 | 250.984 | — | 321.260 | 160.630 |
| HK2520 | 250.984 | — | 321.260 | 200.787 |
| HK3020 | 301.181 | — | 371.457 | 200.787 |
| HK3520 | 351.378 | — | 421.654 | 200.787 |
| HK4020 | 401.575 | — | 471.850 | 200.787 |
| NA49: machined rings, with inner ring | ||||
| NA4900 | 140.551 | 100.394 | 220.866 | 130.512 |
| NA4901 | 160.630 | 120.472 | 240.945 | 130.512 |
| NA4902 | 200.787 | 150.591 | 281.102 | 130.512 |
| NA4903 | 220.866 | 170.669 | 301.181 | 130.512 |
| NA4904 | 250.984 | 200.787 | 371.457 | 170.669 |
| NA4905 | 301.181 | 250.984 | 421.654 | 170.669 |
| NA4906 | 351.378 | 301.181 | 471.850 | 170.669 |
| NA4907 | 421.654 | 351.378 | 552.165 | 200.787 |
| NA4908 | 481.890 | 401.575 | 622.441 | 220.866 |
| NA4909 | 522.047 | 451.772 | 682.677 | 220.866 |
| NA4910 | 582.283 | 501.969 | 722.835 | 220.866 |
| NA4911 | 632.480 | 552.165 | 803.150 | 250.984 |
| NA4912 | 682.677 | 602.362 | 853.346 | 250.984 |
| NA4913 | 722.835 | 652.559 | 903.543 | 250.984 |
| NA4914 | 803.150 | 702.756 | 1003.937 | 301.181 |
| NA4915 | 853.346 | 752.953 | 1054.134 | 301.181 |
| NA4916 | 903.543 | 803.150 | 1104.331 | 301.181 |
| NA4917 | 1003.937 | 853.346 | 1204.724 | 351.378 |
| NA4918 | 1054.134 | 903.543 | 1254.921 | 351.378 |
| NA4919 | 1104.331 | 953.740 | 1305.118 | 351.378 |
| NA4920 | 1154.528 | 1003.937 | 1405.512 | 401.575 |
No exact match. The nearest sizes:
How to read needle bearing numbers
HK 1612: HK = drawn cup, open at both ends; 16 = Fw, the shaft (raceway) diameter in mm; 12 = width C in mm. The outside diameter is not in the number; look it up (22 mm here). BK 1612 is the same cup with one closed end. Suffixes: -2RS = seals both sides (sealed cups are usually wider than open ones of the same Fw, e.g. HK 1216-2RS is 16 mm wide), -B = INA standard design, -ZW = double row cage, TLA 1612 Z is the IKO name for the same size.
NA 4905: NA = needle roller bearing with machined outer ring and inner ring, 49 = dimension series, 05 = bore code (× 5 = 25 mm). RNA 4905 is the same bearing without the inner ring. Its bore is the raceway diameter Fw (30 mm here), so the shaft must be hardened and ground to Fw. -2RS / UU = sealed (slightly wider).
About Needle Roller Bearings
A drawn cup is pressed from thin hardened sheet steel and gets its final roundness only when pressed into the housing. Fit matters: the housing bore is normally N7 (steel) or R7 (light alloy), and the shaft raceway must be hardened to about 58 HRC and ground (usually to h6) because the needles run directly on it. Get the housing fit wrong and the cup is either loose or squeezed so tight the needles bind.
Machined-ring needle bearings (NA49) behave like any other radial bearing and can be fitted with normal fits. They are chosen where radial space is small but loads are high: rocker arms, gearbox idlers, pump shafts, steering columns.
Needle bearings take no axial load. Guide the shaft axially with a shoulder, thrust washer or a separate thrust bearing.
Measuring an unknown drawn cup
Measure the shaft where the needles ran (Fw), the cup outside diameter (D) and the cup width (C). The HK number is HK + Fw + C. Many sizes share an Fw: HK1010 and HK1012 differ only in width.
Questions
What size is an HK1612 needle bearing?
16 mm shaft (Fw), 22 mm outside diameter, 12 mm wide. The HK number gives shaft diameter and width directly; the OD is fixed by ISO 3245.
What is the difference between HK and BK?
HK is open at both ends; BK has one closed end, used at a shaft end to seal it. Same Fw, D and C for the same number.
What size is an NA4905?
25 mm bore, 42 mm outside diameter, 17 mm wide, with a 30 mm raceway (Fw). RNA 4905 is the same without the inner ring.
Does a drawn cup need a hardened shaft?
Yes. The needles run directly on the shaft, which should be hardened to about 58–64 HRC and ground. Otherwise use an inner ring (IR series) of matching Fw.
Sources
- ISO 3245:2015, Rolling bearings, needle roller bearings, drawn cup without inner ring, boundary dimensions
- ISO 1206:2018, Rolling bearings, needle roller bearings with machined rings, boundary dimensions
- Schaeffler (INA) medias: drawn cup needle roller bearings HK, needle roller bearings NA49
- Koyo / NTN / SKF: HK and NA49 product data
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.