Hydraulic Fitting Thread Identification Chart

Thread size, measured thread diameter and pitch for the common hydraulic end connections, sorted by dash size. Dash size is sixteenths of an inch (of the tube OD for JIC, ORFS and O-ring boss, of the pipe size for NPTF and BSP), so a -8 JIC fitting is for 1/2 in tube and has a 3/4-16 thread.

99 sizesChecked 2026-11-157 sources
JIC 37° flare37°SAE 45° flare45°ORFS flat faceO-ringSAE O-ring bossO-ringDIN 24° cone24° incl.BSPP 60° cone60° incl.JIS 30° flare30°NPTF / BSPT tapertaper
How each connection seals, schematic half sections. Cones and flares seal metal to metal on the seat angle shown; ORFS and ORB seal on an O-ring; NPTF and BSPT seal on the tapered thread.Proportions shown, not to scale

Size chartGrouped by connection type; dash size in sixteenths of an inch

99 of 99
FittingThreadDMale thread OD (basic)mminmm · inPPitchmmTPImm · TPITube ODmminmm · inO-ring (AS568)
JIC 37° flare: SAE J514 (UNF/UN thread, 37° cone seat)
JIC -25/16-24 UNF7.940.3131.058243.20.125—
JIC -33/8-24 UNF9.530.3751.058244.80.187—
JIC -47/16-20 UNF11.110.4371.27206.40.250—
JIC -51/2-20 UNF12.700.5001.27207.90.313—
JIC -69/16-18 UNF14.290.5631.411189.50.375—
JIC -83/4-16 UNF19.050.7501.5881612.70.500—
JIC -107/8-14 UNF22.230.8751.8141415.90.625—
JIC -121-1/16-12 UN26.991.0622.1171219.10.750—
JIC -141-3/16-12 UN30.161.1872.1171222.20.875—
JIC -161-5/16-12 UN33.341.3132.1171225.41.000—
JIC -201-5/8-12 UN41.281.6252.1171231.81.250—
JIC -241-7/8-12 UN47.631.8752.1171238.11.500—
JIC -322-1/2-12 UN63.502.5002.1171250.82.000—
SAE O-ring boss (ORB): SAE J1926 / J514 port, straight thread with O-ring
ORB -25/16-24 UNF7.940.3131.058243.20.125-902
ORB -33/8-24 UNF9.530.3751.058244.80.187-903
ORB -47/16-20 UNF11.110.4371.27206.40.250-904
ORB -51/2-20 UNF12.700.5001.27207.90.313-905
ORB -69/16-18 UNF14.290.5631.411189.50.375-906
ORB -83/4-16 UNF19.050.7501.5881612.70.500-908
ORB -107/8-14 UNF22.230.8751.8141415.90.625-910
ORB -121-1/16-12 UN26.991.0622.1171219.10.750-912
ORB -141-3/16-12 UN30.161.1872.1171222.20.875-914
ORB -161-5/16-12 UN33.341.3132.1171225.41.000-916
ORB -201-5/8-12 UN41.281.6252.1171231.81.250-920
ORB -241-7/8-12 UN47.631.8752.1171238.11.500-924
ORB -322-1/2-12 UN63.502.5002.1171250.82.000-932
ORFS: O-ring face seal, SAE J1453 (flat face with O-ring)
ORFS -49/16-1814.290.5631.411186.40.250-011
ORFS -611/16-1617.460.6881.588169.50.375-012
ORFS -813/16-1620.640.8131.5881612.70.500-014
ORFS -101-1425.401.0001.8141415.90.625-016
ORFS -121-3/16-1230.161.1872.1171219.10.750-018
ORFS -161-7/16-1236.511.4372.1171225.41.000-021
ORFS -201-11/16-1242.861.6882.1171231.81.250-025
ORFS -242-1250.802.0002.1171238.11.500-029
SAE 45° flare: SAE J512 (automotive, refrigeration, low-pressure)
SAE 45° -25/16-24 UNF7.940.3131.058243.20.125—
SAE 45° -33/8-24 UNF9.530.3751.058244.80.187—
SAE 45° -47/16-20 UNF11.110.4371.27206.40.250—
SAE 45° -51/2-20 UNF12.700.5001.27207.90.313—
SAE 45° -65/8-18 UNF15.880.6251.411189.50.375—
SAE 45° -83/4-16 UNF19.050.7501.5881612.70.500—
SAE 45° -107/8-14 UNF22.230.8751.8141415.90.625—
SAE 45° -121-1/16-14 UNF26.991.0621.8141419.10.750—
NPTF: Dryseal American taper pipe thread, ASME B1.20.3
NPTF -21/8-27 NPTF10.290.4050.94127——
NPTF -41/4-18 NPTF13.720.5401.41118——
NPTF -63/8-18 NPTF17.150.6751.41118——
NPTF -81/2-14 NPTF21.340.8401.81414——
NPTF -123/4-14 NPTF26.671.0501.81414——
NPTF -161-11.5 NPTF33.401.3152.20911.5——
NPTF -201-1/4-11.5 NPTF42.161.6602.20911.5——
NPTF -241-1/2-11.5 NPTF48.261.9002.20911.5——
NPTF -322-11.5 NPTF60.332.3752.20911.5——
BSPP: British parallel pipe, ISO 228-1 G (60° cone or bonded seal)
BSPP -2G 1/8-289.730.3830.90728——
BSPP -4G 1/4-1913.160.5181.33719——
BSPP -6G 3/8-1916.660.6561.33719——
BSPP -8G 1/2-1420.960.8251.81414——
BSPP -10G 5/8-1422.910.9021.81414——
BSPP -12G 3/4-1426.441.0411.81414——
BSPP -16G 1-1133.251.3092.30911——
BSPP -20G 1-1/4-1141.911.6502.30911——
BSPP -24G 1-1/2-1147.801.8822.30911——
BSPP -32G 2-1159.612.3472.30911——
BSPT: British taper pipe, ISO 7-1 R/Rc
BSPT -2R 1/8-289.730.3830.90728——
BSPT -4R 1/4-1913.160.5181.33719——
BSPT -6R 3/8-1916.660.6561.33719——
BSPT -8R 1/2-1420.960.8251.81414——
BSPT -12R 3/4-1426.441.0411.81414——
BSPT -16R 1-1133.251.3092.30911——
BSPT -20R 1-1/4-1141.911.6502.30911——
BSPT -24R 1-1/2-1147.801.8822.30911——
BSPT -32R 2-1159.612.3472.30911——
JIS 30° flare: JIS B 8363, G (PF) parallel thread
JIS 30° -4G 1/4-19 (PF)13.160.5181.33719——
JIS 30° -6G 3/8-19 (PF)16.660.6561.33719——
JIS 30° -8G 1/2-14 (PF)20.960.8251.81414——
JIS 30° -10G 5/8-14 (PF)22.910.9021.81414——
JIS 30° -12G 3/4-14 (PF)26.441.0411.81414——
JIS 30° -16G 1-11 (PF)33.251.3092.30911——
JIS 30° -20G 1-1/4-11 (PF)41.911.6502.30911——
JIS 30° -24G 1-1/2-11 (PF)47.801.8822.30911——
JIS 30° -32G 2-11 (PF)59.612.3472.30911——
Metric 24° cone, L series (light): DIN 2353 / ISO 8434-1
6LM12×1.512.000.4721.516.960.236—
8LM14×1.514.000.5511.516.980.315—
10LM16×1.516.000.6301.516.9100.394—
12LM18×1.518.000.7091.516.9120.472—
15LM22×1.522.000.8661.516.9150.591—
18LM26×1.526.001.0241.516.9180.709—
22LM30×230.001.181212.7220.866—
28LM36×236.001.417212.7281.102—
35LM45×245.001.772212.7351.378—
42LM52×252.002.047212.7421.654—
Metric 24° cone, S series (heavy): DIN 2353 / ISO 8434-1
6SM14×1.514.000.5511.516.960.236—
8SM16×1.516.000.6301.516.980.315—
10SM18×1.518.000.7091.516.9100.394—
12SM20×1.520.000.7871.516.9120.472—
14SM22×1.522.000.8661.516.9140.551—
16SM24×1.524.000.9451.516.9160.630—
20SM30×230.001.181212.7200.787—
25SM36×236.001.417212.7250.984—
30SM42×242.001.654212.7301.181—
38SM52×252.002.047212.7381.496—

How to identify a hydraulic fitting

Work in this order: sealing method, thread diameter, pitch. Look at how the fitting seals before you measure anything. A cone or flare seat (37°, 45°, 24°, 30°, 60°) seals metal to metal; a flat face with an O-ring in a groove is ORFS; a straight thread with an O-ring at the shoulder is an O-ring boss; a thread with no seat that gets smaller toward the end is a taper pipe thread (NPTF or BSPT).

Measure the outside diameter of a male thread across the crests with a caliper, or the inside diameter of a female thread across the crests of the internal thread. A female thread reads smaller than the listed OD by roughly one thread depth on each side (about 1.1 × pitch in total). Then count the threads per inch, or check the pitch in millimetres with a thread gauge. Metric and inch pitches that look alike (1.5 mm vs 16 TPI = 1.59 mm) separate after 10 threads.

Check the seat angle with a seat-angle gauge or by eye against a known fitting. 37° JIC and 45° SAE share the 7/16-20, 1/2-20, 3/4-16 and 7/8-14 threads; only the seat tells them apart. BSPP, JIS 30° and BSPT share the same 55° thread form; the taper separates BSPT, the maker's marking and seat dimensions separate BSPP from JIS.

Dash numbers: -8 means 8/16 = 1/2 in. On tube fittings (JIC, ORFS, ORB, SAE 45°) it is the tube OD; on hose it is the hose inside diameter (hose sizes); on pipe threads it is the nominal pipe size (-8 NPTF = 1/2-14 NPTF). Metric 24° fittings are named by tube OD and series instead: 12L is 12 mm tube, light series, M18×1.5.

About Hydraulic Fittings

Most hydraulic leaks at a new joint come from mixing two connection types that happen to thread together. The common traps: JIC 37° on an SAE 45° seat (same thread at -2 to -5, -8 and -10), BSPP mixed with JIS 30° (same thread, seats to different standards), and NPTF into a BSPT port at 1/2 and 3/4 (both 14 TPI, 0.4 mm apart in diameter). They turn on a few threads, then leak or weep under pressure.

JIC 37° (SAE J514) is the North American workhorse: male cone, female swivel nut, UNF threads up to -10 and 12-pitch UN threads above. It tolerates repeated assembly but is sensitive to overtightening. ORFS (SAE J1453) seals on an O-ring in the male face and is the choice for high pressure and vibration (6,000 psi class); the threads are different from JIC, so ORFS and JIC never cross-thread at the same dash size.

SAE O-ring boss (ORB) is a port thread: the same UNF thread as JIC of the same dash size, sealed by an AS568 -9xx O-ring that sits in a chamfer at the port face. The O-ring dash number equals the fitting dash size (-8 port, -908 O-ring). Metric equivalents are ISO 6149 ports (metric thread with O-ring) and ISO 1179 BSPP ports.

Metric 24° cone fittings (DIN 2353, now ISO 8434-1, Parker EO / Ermeto type) come in L (light) and S (heavy) series with the same tube OD but different threads: 12L is M18×1.5, 12S is M20×1.5. The nut either compresses a cutting ring onto the tube or seals a swivel cone (DKOL/DKOS) with an O-ring. NPTF and BSPT seal on the tapered thread itself; on hydraulic equipment they are now mostly limited to older machines and low-pressure lines.

Which connections share a thread

The same thread appears in several systems. If the thread matches, the seat decides.

ThreadUsed byTell apart by
5/16-24, 3/8-24, 7/16-20, 1/2-20, 3/4-16, 7/8-14JIC 37° and SAE 45° at -2, -3, -4, -5, -8, -10; ORB ports of the same dash sizeSeat angle 37° vs 45°; ORB has no seat, O-ring at shoulder
9/16-18JIC / ORB -6, ORFS -4ORFS male has a flat face with an O-ring groove
5/8-18SAE 45° -6Not used by JIC (JIC -6 is 9/16-18)
G 1/4 … G 2 (55°, parallel)BSPP (60° cone or bonded washer), JIS 30° flareBoth 60° included cones, dimensioned by different standards; check the maker's marking
R 1/4 … R 2 (55°, taper)BSPTTaper: thread diameter shrinks toward the end
1/2-14 and 3/4-14NPTF -8 / -12 and BSPT -8 / -12Thread angle 60° vs 55°; 1/2 NPTF 21.3 mm vs 20.96 mm
M18×1.5, M22×1.5, M30×2, M36×2, M52×2DIN 24° L and S series (different tube OD)Tube OD and series stamp: M22×1.5 is 15L or 14S

Assembly notes

37° flare (JIC): tighten finger-tight, then turn the nut by flats from wrench resistance (FFWR) as the fitting maker specifies: about 2 flats for the smallest sizes, 1 to 1.5 flats for larger ones. Excess torque cracks the flare or the nose.

ORFS and ORB: always fit a new O-ring of the specified compound (usually 90 durometer nitrile or Viton for ORFS faces). On adjustable ORB elbows, back off the lock nut, screw in until the backup washer touches the port, orient, then hold the body and tighten the lock nut.

Taper pipe threads (NPTF, BSPT): use thread sealant suitable for hydraulic oil, not tape that can shed into the system. Do not use a taper thread to orient an elbow by over- or under-tightening; that is what ORB and ISO 6149 adjustable ports are for.

Questions

What thread is a -8 JIC fitting?

3/4-16 UNF. The -8 means 8/16 = 1/2 in tube (or 1/2 in hose with a -8 hose fitting). A male -8 JIC thread measures about 0.75 in (19.05 mm) across the crests; the female nut opening reads about 0.69 in (17.5 mm).

Will JIC fit SAE 45° flare?

The threads are the same at -2, -3, -4, -5, -8 and -10 (5/16-24 to 7/8-14), so they screw together, but a 37° cone on a 45° seat touches only on a line and leaks. At -6 and -12 the threads differ: JIC 9/16-18 and 1-1/16-12, SAE 45° 5/8-18 and 1-1/16-14. Some adapters have dual 37°/45° seats.

How do I tell ORFS from JIC?

ORFS male fittings have a flat face with an O-ring groove and no cone. Their threads are also different at every dash size: -4 ORFS is 9/16-18, -4 JIC is 7/16-20; -8 ORFS is 13/16-16, -8 JIC is 3/4-16.

Are BSPP and JIS fittings interchangeable?

The threads are identical (ISO 228-1 G, 55°, for example G 1/2 = 20.955 mm, 14 TPI), and both seats are a 60° included cone (BSPP calls it a 60° cone, JIS B 8363 a 30° flare after the half-angle). Nose and seat dimensions come from different standards, so fitting makers sell them as separate parts and do not rate a mixed joint. Match the system stamped on the machine.

What O-ring goes in a -6 SAE O-ring boss port?

An AS568 -906 O-ring (0.468 in ID × 0.078 in cross-section) for the 9/16-18 port. The rule is -9 plus the two-digit dash size: -4 port takes -904, -8 takes -908, -12 takes -912, -16 takes -916.

What thread is a 12L metric fitting?

M18×1.5 for 12 mm OD tube in the light (L) series of DIN 2353 / ISO 8434-1. The heavy series 12S uses M20×1.5. Measure the thread: L and S use different threads for the same tube.

Sources

  1. SAE J514: Hydraulic Tube Fittings (37° flare, O-ring boss)
  2. SAE J1453: Fitting, O-ring Face Seal
  3. SAE J512: Automotive Tube Fittings (45° flare)
  4. ISO 8434-1: Metallic tube connections for fluid power: 24° cone connectors (formerly DIN 2353)
  5. ISO 228-1 / ISO 7-1: Pipe threads (BSPP, BSPT); ASME B1.20.3: Dryseal pipe threads (NPTF)
  6. Parker Hannifin: Catalog 4400 Hose fittings / thread identification guide
  7. Gates: Hydraulic fitting & adapter identification (thread ID guide)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.