Pipe Thread Size Chart (NPT & BSP)
Threads per inch, outside diameter, engagement length and tap drill for American NPT and British BSP pipe threads from 1/16 to 4. The nominal size is the pipe size, not the thread diameter. A 1/2" pipe thread measures about 0.84 in (21 mm) across.
Size chartTap a size for its drawing and full specs
| Thread | nThreads per inchmmTPImm · TPI | DOutside diameter (pipe OD / major Ø)mminmm · in | L₁Engagement length (NPT L1 hand-tight / ISO 7 gauge length)mminmm · in | Tap drill (typical) | Thread angle |
|---|---|---|---|---|---|
| NPT: American taper pipe thread, ASME B1.20.1 | |||||
| 1/16-27 NPT | 0.94127 | 7.9380.313 | 4.10.160 | 1/4 in (6.4 mm) | 60° |
| 1/8-27 NPT | 0.94127 | 10.2870.405 | 4.10.161 | R (0.339 in, 8.6 mm) | 60° |
| 1/4-18 NPT | 1.41118 | 13.7160.540 | 5.80.228 | 7/16 in (11.1 mm) | 60° |
| 3/8-18 NPT | 1.41118 | 17.1450.675 | 6.10.240 | 37/64 in (14.7 mm) | 60° |
| 1/2-14 NPT | 1.81414 | 21.3360.840 | 8.10.320 | 23/32 in (18.3 mm) | 60° |
| 3/4-14 NPT | 1.81414 | 26.6701.050 | 8.60.339 | 59/64 in (23.4 mm) | 60° |
| 1-11.5 NPT | 2.20911.5 | 33.4011.315 | 10.20.400 | 1-5/32 in (29.4 mm) | 60° |
| 1-1/4-11.5 NPT | 2.20911.5 | 42.1641.660 | 10.70.420 | 1-1/2 in (38.1 mm) | 60° |
| 1-1/2-11.5 NPT | 2.20911.5 | 48.2601.900 | 10.70.420 | 1-47/64 in (44.1 mm) | 60° |
| 2-11.5 NPT | 2.20911.5 | 60.3252.375 | 11.10.436 | 2-7/32 in (56.4 mm) | 60° |
| 2-1/2-8 NPT | 3.1758 | 73.0252.875 | 17.30.682 | 2-5/8 in (66.7 mm) | 60° |
| 3-8 NPT | 3.1758 | 88.9003.500 | 19.50.766 | 3-1/4 in (82.6 mm) | 60° |
| 3-1/2-8 NPT | 3.1758 | 101.6004.000 | 20.90.821 | 3-3/4 in (95.3 mm) | 60° |
| 4-8 NPT | 3.1758 | 114.3004.500 | 21.40.844 | 4-1/4 in (108.0 mm) | 60° |
| BSP: British pipe thread, ISO 228 G / ISO 7 R, Rp, Rc | |||||
| G 1/16 BSP | 0.90728 | 7.7230.304 | 40.157 | 6.8 mm | 55° |
| G 1/8 BSP | 0.90728 | 9.7280.383 | 40.157 | 8.8 mm | 55° |
| G 1/4 BSP | 1.33719 | 13.1570.518 | 60.236 | 11.8 mm | 55° |
| G 3/8 BSP | 1.33719 | 16.6620.656 | 6.40.252 | 15.25 mm | 55° |
| G 1/2 BSP | 1.81414 | 20.9550.825 | 8.20.323 | 19.0 mm | 55° |
| G 3/4 BSP | 1.81414 | 26.4411.041 | 9.50.374 | 24.5 mm | 55° |
| G 1 BSP | 2.30911 | 33.2491.309 | 10.40.409 | 30.75 mm | 55° |
| G 1-1/4 BSP | 2.30911 | 41.9101.650 | 12.70.500 | — | 55° |
| G 1-1/2 BSP | 2.30911 | 47.8031.882 | 12.70.500 | — | 55° |
| G 2 BSP | 2.30911 | 59.6142.347 | 15.90.626 | — | 55° |
| G 2-1/2 BSP | 2.30911 | 75.1842.960 | 17.50.689 | — | 55° |
| G 3 BSP | 2.30911 | 87.8843.460 | 20.60.811 | — | 55° |
| G 3-1/2 BSP | 2.30911 | 100.3303.950 | — | — | 55° |
| G 4 BSP | 2.30911 | 113.0304.450 | 25.41.000 | — | 55° |
No exact match. The nearest sizes:
How to read and measure a pipe thread
1/2-14 NPT means a nominal 1/2-inch pipe size, 14 threads per inch, National (American) Pipe Taper. G 1/2 is the British parallel thread for the same pipe size (ISO 228-1), R 1/2 the British external taper thread (ISO 7-1), Rc 1/2 the taper internal and Rp 1/2 the parallel internal thread that mates with R. Older names: BSPP for G, BSPT for R/Rc.
The number is the nominal pipe bore of 19th-century pipe, so the thread is much larger than the name: 1/2" NPT measures about 0.84 in (21.3 mm) across the crests, 1/4" about 0.54 in, 1" about 1.31 in. Measure the outside diameter of a male thread near the middle of the threaded length (NPT tapers, so the end is smaller), then count the threads in one inch or use a thread gauge.
Pitch separates the systems for most sizes: NPT uses 27, 18, 14, 11.5 and 8 TPI; BSP uses 28, 19, 14 and 11. Only 1/2 and 3/4 have the same 14 TPI in both. For those, look at the thread angle (60° NPT, 55° BSP) or the diameter, which differs by about 0.4 mm.
About Pipe Threads
NPT and BSP threads seal differently. Tapered threads (NPT, BSP R/Rc) seal on the thread flanks as the taper wedges tight; they need PTFE tape or paste to fill the spiral leak path. Parallel threads (BSP G) do not seal on the thread at all. The seal is a washer, O-ring or bonded seal against a face or a cone. A G thread screwed into an Rc taper hole will leak.
NPT and BSP are not interchangeable. Most sizes differ in pitch, so they cross-thread after one or two turns. 1/2 and 3/4 share 14 TPI and the diameters are within 0.4 mm, so an NPT fitting can be forced into a BSP part, but the 60°/55° flank angles do not match and the joint seals only on the crests. Use an adapter.
Engagement: a tapered joint is assembled hand-tight to the L1 length, then wrench-tightened about 2–3 more turns (for NPT 1/2–2) to reach the effective length L2. The tap drill sizes listed are the usual sizes for tapping without a taper reamer; with a reamer, use the next smaller drill. Parallel G threads are drilled to just over the minor diameter.
NPTF (Dryseal, ASME B1.20.3) has the same TPI, taper and gauge dimensions as NPT but controls the crest and root truncation so the threads seal by metal-to-metal contact without sealant. It is common in hydraulic and fuel fittings. NPTF and NPT parts screw together, but only NPTF-to-NPTF is dry-sealing. NPS/NPSM (straight pipe threads, ASME B1.20.1) are parallel threads with the NPT pitch, used with gaskets on hose couplings and lamp fittings.
Male, female and the US plumbing abbreviations
MPT, MIP and MNPT all mean a male (external) NPT thread; FPT, FIP and FNPT a female (internal) one. Garden hose threads (GHT, 3/4-11.5 NHR) are a different parallel thread with a washer seal and do not fit 3/4" NPT.
Questions
What is the outside diameter of a 1/2 inch NPT thread?
About 0.840 in (21.3 mm), the outside diameter of 1/2" pipe. Because NPT tapers 1:16, the thread is slightly smaller at the end of the pipe. It has 14 threads per inch.
Are NPT and BSP threads interchangeable?
No. Most sizes have a different pitch (for example 1/4": 18 TPI NPT vs 19 TPI BSP) and all sizes have a different thread angle (60° vs 55°). Only 1/2" and 3/4" share 14 TPI and may screw together, but the joint will not seal reliably. Use an NPT-to-BSP adapter.
What does G 1/2 mean?
G 1/2 is a British parallel pipe thread (ISO 228-1) for 1/2" pipe: 20.955 mm major diameter, 14 threads per inch (1.814 mm pitch), 55° angle. It seals with a washer or O-ring, not on the thread.
What size drill do I use for a 1/4 NPT tap?
7/16 in (11.1 mm) is the usual drill for 1/4-18 NPT without a reamer. For 1/8-27 NPT use R (0.339 in) or 11/32 in; for 1/2-14 NPT use 23/32 in; for 3/4-14 NPT use 59/64 in.
How do I tell NPT from BSP?
Measure the outside diameter and count the threads per inch. 18 or 27 TPI means NPT; 19 or 28 TPI means BSP. For 14 TPI (1/2 and 3/4) compare the diameter: 1/2 NPT ≈ 21.3 mm, G 1/2 ≈ 20.96 mm. A parallel thread with a sealing face or O-ring is BSP G. The identifier above does the comparison.
How many turns should an NPT fitting go in?
Screw it in hand-tight (about 4–5 turns for 1/2" with clean threads), then 2–3 turns with a wrench. Going much further can split a female fitting; much less may leak.
Sources
- ASME B1.20.1: Pipe Threads, General Purpose, Inch
- ISO 228-1:2000, Pipe threads where pressure-tight joints are not made on the threads
- ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads
- Engineers Edge: Whitworth pipe thread (DIN ISO 228) tap drill table
- Machining Doctor: NPT thread charts (B1.20.1 basic dimensions)
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.