Torx Size Chart (Hexalobular Drive, ISO 10664)

A Torx (hexalobular) size number such as T25 names the six-lobe socket. Its point-to-point dimension A is fixed by ISO 10664 (4.50 mm for T25), and each metric screw standard assigns one size per thread: M5 screws take T25.

16 drive sizesChecked 2026-11-154 sources

Size chartTap a size for its drawing and full specs

16 of 16
SizeAPoint to point (A)mminBAcross valleys (B)mminSocket cap screw ISO 14579Pan head ISO 14583Countersunk ISO 14581
T61.750.06891.270.0500M2M2M2
T82.400.09451.750.0689M2.5M2.5M2.5
T102.800.11022.050.0807M3M3M3
T153.350.13192.400.0945—M3.5M3.5
T203.950.15552.850.1122M4M4M4
T254.500.17723.250.1280M5M5M5
T305.600.22054.050.1594M6M6M6
T406.750.26574.850.1909——M8
T457.930.31225.640.2220M8M8—
T508.950.35246.450.2539M10M10M10
T5511.350.44698.050.3169M12——
T6013.450.52959.600.3780M14——
T7015.700.618111.200.4409M16——
T8017.750.698812.800.5039———
T9020.200.795314.400.5669M20——
T10022.400.881916.000.6299———

How to identify a Torx size

Measure across two opposite lobe tips of the recess (or of the bit) with a caliper: that is A. Find the nearest value in the chart. Neighbouring sizes differ by 0.4–0.6 mm in the small range, so a caliper is enough to tell T20 (3.95 mm) from T25 (4.50 mm).

T (or TX, IP in some catalogues) is the internal drive in the screw. E sizes (E4 … E24) are the external Torx heads on some automotive bolts and use different dimensions. An E-socket is not a T-bit.

Torx Plus (IP) and tamper-resistant Torx (a pin in the centre, marked TR or T-H) use the same size numbers. A plain T-bit fits a Torx Plus screw loosely; a tamper-resistant screw needs a bit with a hole in the tip.

About Torx Sizes

The six-lobe drive transmits torque through nearly parallel flanks, so the bit does not push itself out of the recess the way a Phillips bit does. That allows higher tightening torque, less wear and one-handed assembly, which is why Torx has replaced cross recesses in cars, machines and electronics.

ISO 10664 standardises the socket dimensions for the sizes in this chart. The commercial sizes T5, T7, T9 and T27 are widely sold but are not part of ISO 10664, so we list no dimensions for them; T27 is common on US deck and construction screws.

The screw columns show which size each ISO metric screw standard uses. Note that the same thread can take different sizes: an M8 countersunk screw (ISO 14581) takes T40, an M8 pan head or cap screw T45.

Torx bits and hex keys

There is no exact Torx equivalent to a hex key. Very roughly, T25 replaces a 4 mm hex in socket cap screws (M5), T30 a 5 mm hex (M6) and T45 a 6 mm hex (M8); see hex key sizes. Do not hammer a hex key into a Torx recess; it destroys the lobes.

Questions

What Torx size fits an M6 screw?

T30 for ISO hexalobular socket cap, pan and countersunk screws. M3 takes T10, M4 T20, M5 T25, M8 T45 (T40 for countersunk), M10 T50.

How big is a T25 Torx?

4.50 mm point to point and 3.25 mm across the valleys (ISO 10664).

Is TX the same as Torx?

Yes. TX, T and 'hexalobular' (ISO term) all name the same drive. IP or Torx Plus is a modified profile with the same size numbers.

What size is a T27 Torx?

T27 is a commercial size between T25 (4.50 mm) and T30 (5.60 mm) that ISO 10664 does not include. It is common on US deck screws; use a T27 bit, not T25 or T30.

Sources

  1. ISO 10664:2014, Hexalobular internal driving feature for bolts and screws
  2. ISO 10664:2005 sample (Table 1, sockets 6–50)
  3. ISO 14579:2011, Hexalobular socket head cap screws
  4. Westfield Fasteners: ISO 14583 Torx pan head dimensions

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.