Pan Head and Cheese Head Screw Dimensions (Metric)
Pan head machine screws have a wide, low head with rounded edges. The cross recessed version (ISO 7045) and the Torx version (ISO 14583) share one head; the slotted pan head (ISO 1580) has the same diameter but is lower. An M4 pan head is 8 mm across and 3.1 mm high and takes a PH2 or T20 bit.
Size chartTap a size for its drawing and full specs
| Thread | dkHead dia. pan (max)mmin | kHead height ISO 7045 / 14583mmin | Cross recess ISO 7045 | Torx ISO 14583 | Head height ISO 1580 (slotted)mmin | nSlot width (nom.)mmin | Head dia. cheese ISO 1207mmin | Head height cheese ISO 1207mmin |
|---|---|---|---|---|---|---|---|---|
| M1.6 | 3.20.126 | 1.30.051 | PH0 / PZ0 | — | 10.039 | 0.40.016 | 30.118 | 1.10.043 |
| M2 | 40.157 | 1.60.063 | PH0 / PZ0 | T6 | 1.30.051 | 0.50.020 | 3.80.150 | 1.40.055 |
| M2.5 | 50.197 | 2.10.083 | PH1 / PZ1 | T8 | 1.50.059 | 0.60.024 | 4.50.177 | 1.80.071 |
| M3 | 5.60.220 | 2.40.094 | PH1 / PZ1 | T10 | 1.80.071 | 0.80.031 | 5.50.217 | 20.079 |
| M3.5 | 70.276 | 2.60.102 | PH2 / PZ2 | T15 | 2.10.083 | 10.039 | 60.236 | 2.40.094 |
| M4 | 80.315 | 3.10.122 | PH2 / PZ2 | T20 | 2.40.094 | 1.20.047 | 70.276 | 2.60.102 |
| M5 | 9.50.374 | 3.70.146 | PH2 / PZ2 | T25 | 30.118 | 1.20.047 | 8.50.335 | 3.30.130 |
| M6 | 120.472 | 4.60.181 | PH3 / PZ3 | T30 | 3.60.142 | 1.60.063 | 100.394 | 3.90.154 |
| M8 | 160.630 | 60.236 | PH4 / PZ4 | T45 | 4.80.189 | 20.079 | 130.512 | 50.197 |
| M10 | 200.787 | 7.50.295 | PH4 / PZ4 | T50 | 60.236 | 2.50.098 | 160.630 | 60.236 |
No exact match. The nearest sizes:
How to read the chart
All head dimensions are maximum values from the standards. dk is the pan head diameter, shared by ISO 7045 (cross recess), ISO 14583 (Torx) and ISO 1580 (slot). The cross recessed and Torx heads are taller (k ISO 7045) than the slotted one (k ISO 1580), because the recess needs depth.
The cross recess column gives the bit number. ISO 7045 allows type H (Phillips) or type Z (Pozidriv) with the same number; a Pozidriv head has four extra thin radial lines between the arms. Use the matching bit: PH in PZ (or the reverse) cams out and damages both.
The length of a pan or cheese head screw is measured under the head. Thread pitch is the ISO coarse pitch: M3×0.5, M4×0.7, M5×0.8.
About Pan Head Screws
Pan head screws are the general-purpose machine screw for sheet metal, electronics and appliances: the wide head spreads the load and the low height stays out of the way. Cheese head screws (ISO 1207) have a smaller, taller cylindrical head that fits into a counterbore or a narrow space.
The current ISO standards replaced the German DIN 85 (slotted pan), DIN 84 (slotted cheese) and DIN 7985 (cross recessed pan). The old DIN heads are not quite the same: DIN 85 M3 and M5 have 6 mm and 10 mm heads where ISO 1580 has 5.6 mm and 9.5 mm. For new designs use the ISO values; when matching existing parts, check the head.
Torx pan head screws to ISO 14583 have the same head as ISO 7045 and are increasingly common in machine building because the six-lobe drive takes more torque without cam-out. The drive sizes are in the chart; the socket dimensions are on Torx sizes.
Pan head or self-tapping?
A machine screw needs a tapped hole or a nut. Pan head screws for sheet metal without a tapped hole are self-tapping screws (ISO 7049, sizes ST2.2 to ST6.3) with a different, coarser thread. See self-tapping screws.
Questions
What Phillips bit fits an M4 pan head screw?
PH2 (or PZ2 for Pozidriv heads). M2–M2.5 need PH0/PH1, M3 PH1, M3.5–M5 PH2, M6 PH3, M8 and M10 PH4.
What Torx size is an M5 pan head screw?
T25 for ISO 14583 Torx pan heads. M3 takes T10, M4 T20, M6 T30, M8 T45.
What is the head diameter of an M3 pan head screw?
5.6 mm maximum to ISO 7045 and ISO 1580, with a 2.4 mm head height for the cross recessed version and 1.8 mm for the slotted one.
What is the difference between pan head and cheese head?
A pan head is wide and low with a rounded edge; a cheese head (ISO 1207) is smaller in diameter and taller, with a flat top. M5: pan 9.5 × 3.0 mm (slotted), cheese 8.5 × 3.3 mm.
Sources
- ISO 7045:2011, Pan head screws with type H or type Z cross recess, product grade A
- ISO 1580:2011, Slotted pan head screws, product grade A
- ISO 1207:2011, Slotted cheese head screws, product grade A
- ISO 14583:2011, Hexalobular socket pan head screws
- fasten.it: DIN EN ISO 1580 and DIN EN ISO 1207 dimension tables
- Aspen Fasteners: DIN 85 slotted pan head specification
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.