Countersunk Screw Dimensions (Metric Flat Head)
Metric countersunk screws have a 90° conical head that sits flush in a countersink. The two families you meet most are hex socket screws (ISO 10642, formerly DIN 7991) and Phillips or Pozidriv machine screws (ISO 7046, formerly DIN 965), and their head diameters are not the same for the same thread.
Size chartTap a size for its drawing and full specs
| Thread | dkHead dia. ISO 10642 (theor. max)mmin | kHead height ISO 10642 (max)mmin | sHex key ISO 10642 / DIN 7991mmin | Head dia. DIN 7991mmin | Head height DIN 7991mmin | Head dia. ISO 7046 (max)mmin | Head height ISO 7046 (max)mmin | Cross recess ISO 7046 |
|---|---|---|---|---|---|---|---|---|
| M1.6 | — | — | — | — | — | 30.118 | 10.0394 | PH0 / PZ0 |
| M2 | — | — | — | — | — | 3.80.150 | 1.20.0472 | PH0 / PZ0 |
| M2.5 | — | — | — | — | — | 4.70.185 | 1.50.0591 | PH1 / PZ1 |
| M3 | 6.720.2646 | 1.860.0732 | 20.079 | 60.236 | 1.70.0669 | 5.50.217 | 1.650.0650 | PH1 / PZ1 |
| M3.5 | — | — | — | — | — | 7.30.287 | 2.350.0925 | PH2 / PZ2 |
| M4 | 8.960.3528 | 2.480.0976 | 2.50.098 | 80.315 | 2.30.0906 | 8.40.331 | 2.70.1063 | PH2 / PZ2 |
| M5 | 11.20.4409 | 3.10.1220 | 30.118 | 100.394 | 2.80.1102 | 9.30.366 | 2.70.1063 | PH2 / PZ2 |
| M6 | 13.440.5291 | 3.720.1465 | 40.157 | 120.472 | 3.30.1299 | 11.30.445 | 3.30.1299 | PH3 / PZ3 |
| M8 | 17.920.7055 | 4.960.1953 | 50.197 | 160.630 | 4.40.1732 | 15.80.622 | 4.650.1831 | PH4 / PZ4 |
| M10 | 22.40.8819 | 6.20.2441 | 60.236 | 200.787 | 5.50.2165 | 18.30.720 | 50.1969 | PH4 / PZ4 |
| M12 | 26.881.0583 | 7.440.2929 | 80.315 | 240.945 | 6.50.2559 | — | — | — |
| M16 | 33.61.3228 | 8.80.3465 | 100.394 | 301.181 | 7.50.2953 | — | — | — |
| M20 | 40.321.5874 | 10.160.4000 | 120.472 | 361.417 | 8.50.3346 | — | — | — |
No exact match. The nearest sizes:
How to read the chart and measure a countersunk screw
The length of a countersunk screw is measured overall, including the head, because the head ends up flush with the surface. An M6×20 countersunk screw is 20 mm from the top of the head to the tip, unlike a cap screw, where length is measured under the head.
The ISO 10642 head diameter is given as a theoretical maximum: the diameter where the 90° cone would meet the flat top if the edge were perfectly sharp. Real heads have a small flat or rounded edge, so a caliper reads less: between the actual minimum and the theoretical value. Use the theoretical value to size the countersink so the head ends up flush or slightly below the surface.
Phillips and Pozidriv countersunk screws give the recess number (1, 2, 3 …) rather than a dimension. ISO 7046 allows either type H (Phillips) or type Z (Pozidriv) with the same number; drive a Pozidriv screw with a PZ bit, or the bit will cam out.
About Countersunk Screws
This chart covers the metric countersunk machine screws you find in hardware stores and catalogues. ISO 10642 is the hexagon socket countersunk screw, usually in property class 8.8, 10.9 or stainless A2/A4. Its predecessor DIN 7991 is still printed on many boxes, and the two are not dimensionally identical: DIN 7991 heads are smaller and lower (M6: 12 mm vs. 13.44 mm theoretical). Both use the same hex key size.
ISO 7046-1 covers cross recessed countersunk screws in property class 4.8 and stainless, sizes M1.6 to M10. It replaced DIN 965. Again the heads differ slightly: DIN 965 M4 has a 7.5 mm head, ISO 7046 M4 has 8.4 mm. If you are replacing screws in an existing countersink, measure the old head first.
ISO 10642 is a 'reduced loadability' standard: the countersunk head is weaker than a socket cap head, so a 10.9 countersunk screw is not guaranteed to reach the full 10.9 proof load. For high loads use a cap screw with a counterbore instead.
The thread pitch is the ISO coarse pitch for every size: M6 is M6×1, M8 is M8×1.25. Fine-thread countersunk screws exist but are special items.
Countersink diameter
Drill the countersink with a 90° countersink bit until its diameter is slightly larger than the theoretical head diameter dk. The head then ends up flush or a few tenths below the surface. ISO 15065 tabulates countersink sizes for countersunk screws; if you are fitting DIN 7991 screws into an existing ISO-sized countersink, expect them to sit a little low.
Imperial flat head screws use an 82° countersink, not 90°. An inch screw in a metric countersink (or the other way round) touches only at the rim or only at the shank and will not sit flush.
Torx countersunk screws
Hexalobular (Torx) countersunk screws are standardised as ISO 14581 (head like ISO 7046) and ISO 10642 variants with a Torx socket. Typical drives: M3 T10, M4 T20, M5 T25, M6 T30; see Torx sizes.
Questions
What size hex key fits an M6 countersunk screw?
A 4 mm hex key fits M6 countersunk screws to ISO 10642 and DIN 7991. M3 takes 2 mm, M4 2.5 mm, M5 3 mm, M8 5 mm, M10 6 mm and M12 8 mm.
What is the head diameter of an M5 countersunk screw?
ISO 10642 M5: 11.2 mm theoretical (real heads about 9.4–11.2 mm). DIN 7991 M5: 10 mm. Phillips ISO 7046 M5: 9.3 mm max, DIN 965 M5: 9.2 mm.
How is the length of a countersunk screw measured?
Overall, from the top of the head to the end of the thread, because the head sits flush. An M5×16 countersunk screw is 16 mm long including the head.
Are DIN 7991 and ISO 10642 the same?
They are interchangeable in thread, length and key size, but not in head size: ISO 10642 heads are larger and higher. In a countersink made for DIN 7991 an ISO 10642 screw stands slightly proud.
Is a metric countersink 90° or 82°?
Metric countersunk screws have a 90° head. Unified (inch) flat head screws have 82°. Use the matching countersink bit.
Sources
- ISO 10642:2019, Hexagon socket countersunk head screws with reduced loadability
- ISO 7046-1:2011, Cross-recessed countersunk flat head screws (common head), steel 4.8
- Westfield Fasteners: ISO 10642 / DIN 7991 socket countersunk screw dimensions
- fasten.it: DIN EN ISO 7046-1 and DIN 965 dimension tables
- Böllhoff: DIN 965 stainless A4 cross recess, product data sheet
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.