H7/r6 Fit Tolerances

ISO Fits · Hole-basis fits (H hole)

H7/r6: Interference fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +21 / 0 µm, the shaft +41 / +28 µm, giving a maximum clearance of −7 µm and a minimum clearance of −41 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.

Fit type
Interference
Max. clearance at ⌀25 mm
−7 µm−0.00028 in−0.00028 in−7 µm
Min. clearance at ⌀25 mm (− = interference)
−41 µm−0.00161 in−0.00161 in−41 µm

Drawing

zero line = nominal sizeHole H7Shaft r6+210+41+28⌀25 H7/r6: interference 7 to 41 µm
Tolerance zones at ⌀25 mm, deviations in µm; vertical scale enlarged.Proportions shown, not to scale

H7/r6 specifications

Fit typeInterference
Hole limits at ⌀25 mm (µm)+21 / 0
Shaft limits at ⌀25 mm (µm)+41 / +28
Max. clearance at ⌀25 mm−7 µm−0.00028 in
Min. clearance at ⌀25 mm (− = interference)−41 µm−0.00161 in

H7/r6 limits for every size range (µm)

Size (mm)Hole ES / EIShaft es / eiMax. clearanceMin. clearanceType
≤ 3+10 / 0+16 / +100−16interference
3–6+12 / 0+23 / +15−3−23interference
6–10+15 / 0+28 / +19−4−28interference
10–18+18 / 0+34 / +23−5−34interference
18–30+21 / 0+41 / +28−7−41interference
30–50+25 / 0+50 / +34−9−50interference
50–65+30 / 0+60 / +41−11−60interference
65–80+30 / 0+62 / +43−13−62interference
80–100+35 / 0+73 / +51−16−73interference
100–120+35 / 0+76 / +54−19−76interference
120–140+40 / 0+88 / +63−23−88interference
140–160+40 / 0+90 / +65−25−90interference
160–180+40 / 0+93 / +68−28−93interference
180–200+46 / 0+106 / +77−31−106interference
200–225+46 / 0+109 / +80−34−109interference
225–250+46 / 0+113 / +84−38−113interference
250–280+52 / 0+126 / +94−42−126interference
280–315+52 / 0+130 / +98−46−130interference
315–355+57 / 0+144 / +108−51−144interference
355–400+57 / 0+150 / +114−57−150interference
400–450+63 / 0+166 / +126−63−166interference
450–500+63 / 0+172 / +132−69−172interference

Medium drive fit. Pressed parts that transmit moderate torque: bushes, bearing bushes in cast iron, gear rims.

Other fits of the same type (Interference)

All ISO fits

Compare all 24 fits in the ISO Fits chart →

Sources

  1. ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
  2. ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
  3. ANSI B4.2-1978 (R2020): Preferred metric limits and fits

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.