S7/h6 Fit Tolerances

ISO Fits · Shaft-basis fits (h shaft)

S7/h6: Interference fit, Shaft-basis fits (h shaft). At ⌀25 mm the hole is −27 / −48 µm, the shaft 0 / −13 µm, giving a maximum clearance of −14 µm and a minimum clearance of −48 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.

Fit type
Interference
Max. clearance at ⌀25 mm
−14 µm−0.00055 in−0.00055 in−14 µm
Min. clearance at ⌀25 mm (− = interference)
−48 µm−0.00189 in−0.00189 in−48 µm

Drawing

zero line = nominal sizeHole S7Shaft h6−27−480−13⌀25 S7/h6: interference 14 to 48 µm
Tolerance zones at ⌀25 mm, deviations in µm; vertical scale enlarged.Proportions shown, not to scale

S7/h6 specifications

Fit typeInterference
Hole limits at ⌀25 mm (µm)−27 / −48
Shaft limits at ⌀25 mm (µm)0 / −13
Max. clearance at ⌀25 mm−14 µm−0.00055 in
Min. clearance at ⌀25 mm (− = interference)−48 µm−0.00189 in

S7/h6 limits for every size range (µm)

Size (mm)Hole ES / EIShaft es / eiMax. clearanceMin. clearanceType
≤ 3−14 / −240 / −6−8−24interference
3–6−15 / −270 / −8−7−27interference
6–10−17 / −320 / −9−8−32interference
10–18−21 / −390 / −11−10−39interference
18–30−27 / −480 / −13−14−48interference
30–50−34 / −590 / −16−18−59interference
50–65−42 / −720 / −19−23−72interference
65–80−48 / −780 / −19−29−78interference
80–100−58 / −930 / −22−36−93interference
100–120−66 / −1010 / −22−44−101interference
120–140−77 / −1170 / −25−52−117interference
140–160−85 / −1250 / −25−60−125interference
160–180−93 / −1330 / −25−68−133interference
180–200−105 / −1510 / −29−76−151interference
200–225−113 / −1590 / −29−84−159interference
225–250−123 / −1690 / −29−94−169interference
250–280−138 / −1900 / −32−106−190interference
280–315−150 / −2020 / −32−118−202interference
315–355−169 / −2260 / −36−133−226interference
355–400−187 / −2440 / −36−151−244interference
400–450−209 / −2720 / −40−169−272interference
450–500−229 / −2920 / −40−189−292interference

Shaft-basis force fit: permanent assembly of hubs on h6 shafts.

Other fits of the same type (Interference)

All ISO fits

Compare all 24 fits in the ISO Fits chart →

Sources

  1. ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
  2. ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
  3. ANSI B4.2-1978 (R2020): Preferred metric limits and fits

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.