H7/s6 Fit Tolerances

ISO Fits · Hole-basis fits (H hole)

H7/s6: Interference fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +21 / 0 µm, the shaft +48 / +35 µm, giving a maximum clearance of −14 µm and a minimum clearance of −48 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.

Fit type
Interference
Max. clearance at ⌀25 mm
−14 µm−0.00055 in−0.00055 in−14 µm
Min. clearance at ⌀25 mm (− = interference)
−48 µm−0.00189 in−0.00189 in−48 µm

Drawing

zero line = nominal sizeHole H7Shaft s6+210+48+35⌀25 H7/s6: interference 14 to 48 µm
Tolerance zones at ⌀25 mm, deviations in µm; vertical scale enlarged.Proportions shown, not to scale

H7/s6 specifications

Fit typeInterference
Hole limits at ⌀25 mm (µm)+21 / 0
Shaft limits at ⌀25 mm (µm)+48 / +35
Max. clearance at ⌀25 mm−14 µm−0.00055 in
Min. clearance at ⌀25 mm (− = interference)−48 µm−0.00189 in

H7/s6 limits for every size range (µm)

Size (mm)Hole ES / EIShaft es / eiMax. clearanceMin. clearanceType
≤ 3+10 / 0+20 / +14−4−20interference
3–6+12 / 0+27 / +19−7−27interference
6–10+15 / 0+32 / +23−8−32interference
10–18+18 / 0+39 / +28−10−39interference
18–30+21 / 0+48 / +35−14−48interference
30–50+25 / 0+59 / +43−18−59interference
50–65+30 / 0+72 / +53−23−72interference
65–80+30 / 0+78 / +59−29−78interference
80–100+35 / 0+93 / +71−36−93interference
100–120+35 / 0+101 / +79−44−101interference
120–140+40 / 0+117 / +92−52−117interference
140–160+40 / 0+125 / +100−60−125interference
160–180+40 / 0+133 / +108−68−133interference
180–200+46 / 0+151 / +122−76−151interference
200–225+46 / 0+159 / +130−84−159interference
225–250+46 / 0+169 / +140−94−169interference
250–280+52 / 0+190 / +158−106−190interference
280–315+52 / 0+202 / +170−118−202interference
315–355+57 / 0+226 / +190−133−226interference
355–400+57 / 0+244 / +208−151−244interference
400–450+63 / 0+272 / +232−169−272interference
450–500+63 / 0+292 / +252−189−292interference

Force or shrink fit. High interference: permanent assembly of hubs, gear rims, couplings without a key. At larger sizes assemble by heating the hub.

Other fits of the same type (Interference)

All ISO fits

Compare all 24 fits in the ISO Fits chart →

Sources

  1. ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
  2. ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
  3. ANSI B4.2-1978 (R2020): Preferred metric limits and fits

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.