P7/h6 Fit Tolerances
ISO Fits · Shaft-basis fits (h shaft)
P7/h6: Interference fit, Shaft-basis fits (h shaft). At ⌀25 mm the hole is −14 / −35 µm, the shaft 0 / −13 µm, giving a maximum clearance of −1 µm and a minimum clearance of −35 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Interference
- Max. clearance at ⌀25 mm
- −1 µm−0.00004 in−0.00004 in−1 µm
- Min. clearance at ⌀25 mm (− = interference)
- −35 µm−0.00138 in−0.00138 in−35 µm
Drawing
P7/h6 specifications
| Fit type | Interference |
|---|---|
| Hole limits at ⌀25 mm (µm) | −14 / −35 |
| Shaft limits at ⌀25 mm (µm) | 0 / −13 |
| Max. clearance at ⌀25 mm | −1 µm−0.00004 in |
| Min. clearance at ⌀25 mm (− = interference) | −35 µm−0.00138 in |
P7/h6 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | −6 / −16 | 0 / −6 | 0 | −16 | interference |
| 3–6 | −8 / −20 | 0 / −8 | 0 | −20 | interference |
| 6–10 | −9 / −24 | 0 / −9 | 0 | −24 | interference |
| 10–18 | −11 / −29 | 0 / −11 | 0 | −29 | interference |
| 18–30 | −14 / −35 | 0 / −13 | −1 | −35 | interference |
| 30–50 | −17 / −42 | 0 / −16 | −1 | −42 | interference |
| 50–80 | −21 / −51 | 0 / −19 | −2 | −51 | interference |
| 80–120 | −24 / −59 | 0 / −22 | −2 | −59 | interference |
| 120–180 | −28 / −68 | 0 / −25 | −3 | −68 | interference |
| 180–250 | −33 / −79 | 0 / −29 | −4 | −79 | interference |
| 250–315 | −36 / −88 | 0 / −32 | −4 | −88 | interference |
| 315–400 | −41 / −98 | 0 / −36 | −5 | −98 | interference |
| 400–500 | −45 / −108 | 0 / −40 | −5 | −108 | interference |
Shaft-basis light press fit: pressed bushes and pins in holes made with a P7 reamer.
Other fits of the same type (Interference)
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.