H7/p6 Fit Tolerances
ISO Fits · Hole-basis fits (H hole)
H7/p6: Interference fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +21 / 0 µm, the shaft +35 / +22 µm, giving a maximum clearance of −1 µm and a minimum clearance of −35 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Interference
- Max. clearance at ⌀25 mm
- −1 µm−0.00004 in−0.00004 in−1 µm
- Min. clearance at ⌀25 mm (− = interference)
- −35 µm−0.00138 in−0.00138 in−35 µm
Drawing
H7/p6 specifications
| Fit type | Interference |
|---|---|
| Hole limits at ⌀25 mm (µm) | +21 / 0 |
| Shaft limits at ⌀25 mm (µm) | +35 / +22 |
| Max. clearance at ⌀25 mm | −1 µm−0.00004 in |
| Min. clearance at ⌀25 mm (− = interference) | −35 µm−0.00138 in |
H7/p6 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +10 / 0 | +12 / +6 | +4 | −12 | transition |
| 3–6 | +12 / 0 | +20 / +12 | 0 | −20 | interference |
| 6–10 | +15 / 0 | +24 / +15 | 0 | −24 | interference |
| 10–18 | +18 / 0 | +29 / +18 | 0 | −29 | interference |
| 18–30 | +21 / 0 | +35 / +22 | −1 | −35 | interference |
| 30–50 | +25 / 0 | +42 / +26 | −1 | −42 | interference |
| 50–80 | +30 / 0 | +51 / +32 | −2 | −51 | interference |
| 80–120 | +35 / 0 | +59 / +37 | −2 | −59 | interference |
| 120–180 | +40 / 0 | +68 / +43 | −3 | −68 | interference |
| 180–250 | +46 / 0 | +79 / +50 | −4 | −79 | interference |
| 250–315 | +52 / 0 | +88 / +56 | −4 | −88 | interference |
| 315–400 | +57 / 0 | +98 / +62 | −5 | −98 | interference |
| 400–500 | +63 / 0 | +108 / +68 | −5 | −108 | interference |
Locational interference fit, the lightest press fit. Parts are pressed together cold and can be dismantled; they locate rigidly but cannot transmit high torque by friction alone. At sizes up to 3 mm the limits allow a few µm of clearance.
Other fits of the same type (Interference)
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.