Heat Shrink Tubing Size Chart
A heat-shrink size is its supplied (expanded) inside diameter; the shrink ratio says how small it gets. A 1/4" 2:1 tube starts at 6.35 mm and recovers to at most 3.18 mm; a 1/4" 3:1 tube goes down to 2.1 mm. Pick a tube that slides over the largest part (connector, splice) and still recovers below the smallest diameter it must grip.
Size chartRecovered ID = supplied ÷ ratio; check the data sheet for wall thickness
| Size | Supplied ID (min.)mminmm · in | Recovered ID (max.)mminmm · in | Shrink ratio | Suggested diameter rangemminmm · in |
|---|---|---|---|---|
| Inch sizes, 2:1 | ||||
| 3/64" 2:1 | 1.190.047 | 0.60.024 | 2:1 | 0.7–10.03–0.04 |
| 1/16" 2:1 | 1.590.063 | 0.790.031 | 2:1 | 0.9–1.30.03–0.05 |
| 3/32" 2:1 | 2.380.094 | 1.190.047 | 2:1 | 1.3–1.90.05–0.07 |
| 1/8" 2:1 | 3.170.125 | 1.590.063 | 2:1 | 1.8–2.50.07–0.10 |
| 3/16" 2:1 | 4.760.187 | 2.380.094 | 2:1 | 2.6–3.80.10–0.15 |
| 1/4" 2:1 | 6.350.250 | 3.170.125 | 2:1 | 3.5–5.10.14–0.20 |
| 3/8" 2:1 | 9.520.375 | 4.760.187 | 2:1 | 5.2–7.60.21–0.30 |
| 1/2" 2:1 | 12.70.500 | 6.350.250 | 2:1 | 7–10.20.28–0.40 |
| 3/4" 2:1 | 19.050.750 | 9.520.375 | 2:1 | 10.5–15.20.41–0.60 |
| 1" 2:1 | 25.41.000 | 12.70.500 | 2:1 | 14–20.30.55–0.80 |
| 1-1/2" 2:1 | 38.11.500 | 19.050.750 | 2:1 | 21–30.50.82–1.20 |
| 2" 2:1 | 50.82.000 | 25.41.000 | 2:1 | 27.9–40.61.10–1.60 |
| 3" 2:1 | 76.23.000 | 38.11.500 | 2:1 | 41.9–611.65–2.40 |
| 4" 2:1 | 101.64.000 | 50.82.000 | 2:1 | 55.9–81.32.20–3.20 |
| Inch sizes, 3:1 (usually adhesive-lined) | ||||
| 3/32" 3:1 | 2.380.094 | 0.790.031 | 3:1 | 0.9–1.90.03–0.07 |
| 1/8" 3:1 | 3.170.125 | 1.060.042 | 3:1 | 1.2–2.50.05–0.10 |
| 3/16" 3:1 | 4.760.187 | 1.590.063 | 3:1 | 1.8–3.80.07–0.15 |
| 1/4" 3:1 | 6.350.250 | 2.120.083 | 3:1 | 2.3–5.10.09–0.20 |
| 3/8" 3:1 | 9.520.375 | 3.170.125 | 3:1 | 3.5–7.60.14–0.30 |
| 1/2" 3:1 | 12.70.500 | 4.230.167 | 3:1 | 4.7–10.20.18–0.40 |
| 3/4" 3:1 | 19.050.750 | 6.350.250 | 3:1 | 7–15.20.27–0.60 |
| 1" 3:1 | 25.41.000 | 8.470.333 | 3:1 | 9.3–20.30.37–0.80 |
| 1-1/2" 3:1 | 38.11.500 | 12.70.500 | 3:1 | 14–30.50.55–1.20 |
| Metric sizes, 2:1 | ||||
| 1 mm 2:1 | 10.039 | 0.50.020 | 2:1 | 0.6–0.80.02–0.03 |
| 1.5 mm 2:1 | 1.50.059 | 0.750.030 | 2:1 | 0.8–1.20.03–0.05 |
| 2 mm 2:1 | 20.079 | 10.039 | 2:1 | 1.1–1.60.04–0.06 |
| 2.5 mm 2:1 | 2.50.098 | 1.250.049 | 2:1 | 1.4–20.05–0.08 |
| 3 mm 2:1 | 30.118 | 1.50.059 | 2:1 | 1.7–2.40.06–0.09 |
| 3.5 mm 2:1 | 3.50.138 | 1.750.069 | 2:1 | 1.9–2.80.08–0.11 |
| 4 mm 2:1 | 40.157 | 20.079 | 2:1 | 2.2–3.20.09–0.13 |
| 5 mm 2:1 | 50.197 | 2.50.098 | 2:1 | 2.8–40.11–0.16 |
| 6 mm 2:1 | 60.236 | 30.118 | 2:1 | 3.3–4.80.13–0.19 |
| 8 mm 2:1 | 80.315 | 40.157 | 2:1 | 4.4–6.40.17–0.25 |
| 10 mm 2:1 | 100.394 | 50.197 | 2:1 | 5.5–80.22–0.31 |
| 12 mm 2:1 | 120.472 | 60.236 | 2:1 | 6.6–9.60.26–0.38 |
| 14 mm 2:1 | 140.551 | 70.276 | 2:1 | 7.7–11.20.30–0.44 |
| 16 mm 2:1 | 160.630 | 80.315 | 2:1 | 8.8–12.80.35–0.50 |
| 18 mm 2:1 | 180.709 | 90.354 | 2:1 | 9.9–14.40.39–0.57 |
| 20 mm 2:1 | 200.787 | 100.394 | 2:1 | 11–160.43–0.63 |
| 25 mm 2:1 | 250.984 | 12.50.492 | 2:1 | 13.8–200.54–0.79 |
| 30 mm 2:1 | 301.181 | 150.591 | 2:1 | 16.5–240.65–0.94 |
| 40 mm 2:1 | 401.575 | 200.787 | 2:1 | 22–320.87–1.26 |
| 50 mm 2:1 | 501.969 | 250.984 | 2:1 | 27.5–401.08–1.57 |
No exact match. The nearest sizes:
Supplied ID, recovered ID and ratio
The nominal size is the minimum expanded inside diameter as supplied. The recovered inside diameter is the maximum ID after free recovery (heated with nothing inside). The ratio links them: 2:1 recovers to half, 3:1 to a third, 4:1 to a quarter. Metric tubes are often labelled with both numbers, e.g. 6/3 (2:1) or 12/4 (3:1).
Rule of thumb for choosing: the tube should slide over the largest diameter with about 20 % clearance (largest ≤ 0.8 × supplied ID) and shrink to at least about 10 % smaller than the smallest diameter (smallest ≥ 1.1 × recovered ID), so it grips firmly. The last column applies this rule.
Tubing also shrinks lengthwise, typically up to 5–10 % for polyolefin; cut it a little long. The wall gets thicker as it shrinks: a recovered thin-wall 2:1 tube is about 0.4–0.9 mm thick depending on size and maker.
About Heat Shrink Sizes
The table lists the common inch series (2:1 from 3/64" to 4" and 3:1 from 3/32" to 1-1/2"), and the metric 2:1 sizes sold in kits and on reels. Recovered ID is the nominal supplied ID divided by the ratio; real tubes meet or beat it. Wall thickness depends on the product family, so it is not listed.
2:1 polyolefin (TE RNF-100, 3M FP-301 type) is the general-purpose tube for insulating solder joints, bundling and color-coding, rated typically 600 V and −55 to 135 °C. 3:1 and 4:1 adhesive-lined (dual-wall) tube has a hot-melt inner layer that flows and seals. Use it for waterproof splices, connectors outdoors and automotive or marine wiring, and where a big connector has to pass over a thin cable.
Other materials: PVC (cheap, lower temperature), fluoropolymer PTFE/FEP/PVDF (high temperature, chemical resistance; PTFE about −55 to 175 °C), elastomer (flexible, fuel resistant), and medium/heavy-wall tubes for cable joints up to 1 kV. Use a heat gun, not a lighter; shrink from the middle outwards to push air out.
Questions
What size heat shrink for 12 AWG wire?
12 AWG THHN is about 3.3 mm (0.13 in) over the insulation. A 3/16" (4.8 mm) 2:1 tube slides over it and recovers to 2.4 mm, gripping firmly. Over a butt splice (about 6–7 mm) a 2:1 tube large enough to pass the splice will not grip the wire; use 3/8" 3:1 adhesive-lined tube (9.5 → 3.2 mm).
What does 2:1 or 3:1 mean on heat shrink?
The shrink ratio. A 2:1 tube recovers to half its supplied diameter (1/4" → 1/8"), a 3:1 tube to a third (1/4" → about 1/12", 2.1 mm). Higher ratios cover a wider range of diameters with one size.
How much does heat shrink shrink in length?
Typically up to 5 % for 2:1 polyolefin and up to about 10 % for some 3:1 and 4:1 tubes. Cut 10 % longer than needed.
What is adhesive-lined heat shrink?
Dual-wall tube with a thermoplastic adhesive inside that melts during shrinking and seals against moisture. Usually 3:1 or 4:1. Use it outdoors, underground, in vehicles and boats.
What does 6/3 or 12/4 mean on metric heat shrink?
Supplied ID / recovered ID in mm. 6/3 is a 2:1 tube from 6 mm down to 3 mm; 12/4 is a 3:1 tube from 12 mm down to 4 mm.
Sources
- UL 224: Extruded insulating tubing (heat-shrink tubing designations and ratings)
- SAE AMS-DTL-23053: Insulation sleeving, electrical, heat shrinkable (expanded/recovered ID definitions)
- TE Connectivity Raychem: RNF-100 (2:1 polyolefin) and ATUM (adhesive-lined) data sheets
- 3M: FP-301 (2:1) and EPS-300 (3:1 adhesive-lined) heat shrink tubing data
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.