Cable Gland Sizes: Metric, PG and NPT Thread Chart

Entry thread sizes of cable glands (metric M12 × 1.5 to M63 × 1.5, the older German PG7 to PG48, and NPT conduit sizes) with the hole to drill or tap for each. The quick rule for metric glands: the number is the thread diameter, every size has a 1.5 mm pitch, and the clearance hole is that number plus 0.2–0.5 mm (M20 → 20.2–20.5 mm hole).

24 thread sizesChecked 2026-11-157 sources

Size chartTap a size for its drawing and full specs

24 of 24
ThreaddThread outside diametermminmm · inPThread pitchmmTPImm · TPI⌀Clearance holemminmm · inTap drill (threaded entry)mminmm · inCable range, examplemminmm · in
Metric M × 1.5 (EN 60423)
M12 × 1.5120.4721.516.912.2–12.50.480–0.49210.50.4133.5–70.138–0.276
M16 × 1.5160.6301.516.916.2–16.50.638–0.65014.50.5714–100.157–0.394
M20 × 1.5200.7871.516.920.2–20.50.795–0.80718.50.7287–130.276–0.512
M25 × 1.5250.9841.516.925.2–25.50.992–1.00423.50.9258–170.315–0.669
M32 × 1.5321.2601.516.932.2–32.51.268–1.28030.51.2019–210.354–0.827
M40 × 1.5401.5751.516.940.2–40.51.583–1.59438.51.51616–280.630–1.102
M50 × 1.5501.9691.516.950.2–50.51.976–1.98848.51.90927–341.063–1.339
M63 × 1.5632.4801.516.963.2–63.52.488–2.50061.52.42134–451.339–1.772
PG: steel conduit thread (DIN 40430)
PG712.50.4921.2720.012.7–130.500–0.51211.40.449—
PG915.20.5981.41118.015.4–15.70.606–0.618140.551—
PG1118.60.7321.41118.018.8–19.10.740–0.75217.250.679—
PG13.520.40.8031.41118.020.6–20.90.811–0.823190.748—
PG1622.50.8861.41118.022.7–230.894–0.90621.250.837—
PG2128.31.1141.58816.028.5–28.81.122–1.13426.751.053—
PG29371.4571.58816.037.2–37.51.465–1.476——
PG36471.8501.58816.047.2–47.51.858–1.87045.51.791—
PG42542.1261.58816.054.2–54.52.134–2.146——
PG4859.32.3351.58816.059.5–59.82.343–2.354——
NPT conduit entries (ASME B1.20.1)
1/2" NPT21.340.8401.81414.022.50.88518.260.719—
3/4" NPT26.671.0501.81414.028.31.11523.420.922—
1" NPT33.41.3152.20911.534.61.36229.371.156—
1-1/4" NPT42.161.6602.20911.543.21.70138.11.500—
1-1/2" NPT48.261.9002.20911.549.61.95144.051.734—
2" NPT60.332.3752.20911.5—56.362.219—

How to identify a gland thread

Measure the outside diameter of the male thread and count the threads over 10 mm or 1 inch. Metric gland threads are always 1.5 mm pitch (17 threads per inch) and the diameter is a round number: 12, 16, 20, 25, 32, 40, 50 or 63 mm. PG threads have a coarse, shallow 80° thread with 20, 18 or 16 threads per inch and diameters that look odd in mm: 12.5, 15.2, 18.6, 20.4, 22.5 mm … NPT threads are tapered (you can feel the cone) with 14 or 11.5 threads per inch.

The size names do not match across systems: PG13.5 is 20.4 mm, not 13.5 mm, and it will not go into an M20 hole. PG designations come from old steel conduit bore sizes. The nearest metric replacements by thread diameter are PG7 → M12, PG9 → M16, PG11 → M20, PG13.5 / PG16 → M20 or M25, PG21 → M25 or M32, PG29 → M32 or M40, PG36 → M40 or M50, PG42 → M50, PG48 → M63, but always check the cable range, which decides the gland.

The cable range is the outside diameter of the cable sheath the gland seals on. It depends on the seal insert, not only on the thread: one M20 gland may take 6–12 mm, another 10–14 mm. The ranges listed are examples from one common nylon gland range; choose the gland by its printed clamping range.

About Cable Glands

A cable gland seals and strain-relieves a cable where it enters an enclosure. The entry thread is the only part that is truly standardized: the thread on the gland must match the tapped hole or, more often, the plain clearance hole and locknut.

Metric (EN 60423) threads replaced PG in Europe when EN 50262 (now EN 62444) took over from VDE 0619 in 2000. All sizes have a fine 1.5 mm pitch, so one clearance-hole rule (thread + 0.2 to 0.5 mm) and one tap-drill rule (thread − 1.5 mm: M20 → 18.5 mm) cover the range. Knockouts in metric enclosures are punched to these hole sizes.

PG threads (DIN 40430) are still found on older machines, valves, sensors and lights; PG7, PG9, PG11, PG13.5 and PG16 are the common sizes. The flank angle is 80° and the profile is shallow, so a PG gland will not thread into a metric hole even when the diameters are close.

NPT glands (often called cord grips in the US) screw into tapped hubs or pass through conduit knockouts with a locknut. The thread size is the pipe size: a 1/2" NPT gland has a 0.840" (21.3 mm) thread and fits the standard 7/8" knockout for 1/2" conduit.

IP rating and thread sealing

A gland's IP68 rating applies only with its sealing washer or O-ring between body and enclosure, and with a cable inside the clamping range. In a tapped hole in thin sheet metal, use a locknut or a sealing ring anyway: a plain thread in 1–2 mm sheet does not seal. NPT threads seal on the taper with thread sealant; metric and PG threads do not seal by themselves.

Questions

What size hole do I drill for an M20 cable gland?

20.2 to 20.5 mm for a gland held with a locknut (most makers specify 20.5 mm). For a tapped entry, drill 18.5 mm and tap M20 × 1.5.

What is the difference between PG and metric cable glands?

PG (DIN 40430) threads have inch-based pitches (20, 18 or 16 TPI), an 80° thread angle and diameters like 15.2 or 20.4 mm; metric glands have a 60° thread with 1.5 mm pitch and whole-mm diameters. They are not interchangeable even when the diameters are close (PG13.5 = 20.4 mm vs M20 = 20 mm).

What is the thread diameter of PG9?

15.2 mm with 18 threads per inch (1.411 mm pitch). Clearance hole about 15.4–15.7 mm, tap drill 14.0 mm. The nearest metric gland is M16 × 1.5.

Which cable gland size do I need for my cable?

Measure the cable's outside diameter and pick a gland whose clamping range covers it, ideally in the middle of the range. The thread size follows: a 10 mm cable typically needs an M20 gland (e.g. 7–13 mm range); a 6 mm cable fits an M16 (about 4–10 mm) or a reduced-range M20.

Does a 1/2 inch NPT gland fit a 7/8 inch knockout?

Yes. A 1/2" NPT thread is 0.840" (21.3 mm) in diameter and passes through the standard 7/8" (nominally; 0.885" punched) knockout for 1/2" conduit, secured with a locknut.

Sources

  1. DIN 40430: Steel conduit thread (PG): dimensions, via gewindebohrer.de thread tables
  2. Heyco: PG hub liquid-tight cordgrip, DIN 40430 thread specifications
  3. Newman Tools: PG steel conduit taps per DIN 40430 (tap drill sizes)
  4. LAPP: SKINTOP ST-M cable glands, metric (clamping ranges)
  5. metric-bolt-torque.com: Cable gland sizes and entry holes
  6. Greenlee: Standard round knockout punches (hole sizes per conduit trade size)
  7. ASME B1.20.1: Pipe threads, general purpose (inch), NPT

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.