Lifting Chain WLL Chart: Grade 80 & Grade 100

Single-leg working load limits of alloy steel lifting chain. Grade 100 carries 25 % more than Grade 80 of the same size: a 3/8 in chain is rated 7,100 lb in Grade 80 and 8,800 lb in Grade 100; a 10 mm EN 818-2 grade 8 chain 3.15 t.

21 sizesChecked 2026-11-156 sources

Size chartTap a size for its drawing and full specs

21 of 21
SizedWire diameter (metric size)mminmm · inWLL Grade 80 (single leg)tlbt · lbWLL Grade 100 (single leg)tlbt · lbMin. breaking force, Grade 80 (4 × WLL)tlbt · lb
Metric: EN 818-2 grade 8; grade 10 per makers' tables
6 mm60.2361.122,4691.43,0864.59,877
7 mm70.2761.53,307—613,228
8 mm80.31524,4092.55,512817,637
10 mm100.3943.156,94548,81812.627,778
13 mm130.5125.311,6846.714,77121.246,738
16 mm160.630817,6371022,0463270,548
18 mm180.7091022,046—4088,185
20 mm200.78712.527,5581635,27450110,231
22 mm220.8661533,069—60132,277
26 mm261.02421.246,738—84.8186,952
32 mm321.26031.569,446—126277,782
Inch: ASTM A391 Grade 80 / ASTM A973 Grade 100 (NACM)
7/32″5.50.2170.952,1001.222,7003.88,400
9/32″70.2761.593,5001.954,3006.414,000
5/16″80.3152.044,5002.595,7008.218,000
3/8″100.3943.227,1003.998,80012.928,400
1/2″130.5125.4412,0006.815,00021.848,000
5/8″160.6308.2118,10010.2522,60032.872,400
3/4″200.78712.8428,30016.0135,30051.3113,200
7/8″220.86615.5134,20019.3742,70062.1136,800
1″261.02421.6447,70027.0859,70086.5190,800
1-1/4″321.26032.7972,3004190,400131.2289,200

How to identify lifting chain

Lifting chain is identified by grade and size, embossed on the links every metre or so: 8, 80, G8 or T for Grade 80, 10 or 100 for Grade 100, often with the maker's mark. Unmarked chain, and hardware or transport chain (Grade 30, 43, 70; gold or yellow chromate), must never be used for overhead lifting.

The size is the wire diameter of the link: caliper the link stock away from the weld. Inch and metric sizes are the same chain sold under two names: 3/8 in Grade 80 is 10 mm, 1/2 in is 13 mm, 5/8 in is 16 mm.

The WLL in the chart is for one leg pulled straight. In a two-leg sling at 60° from horizontal (30° from vertical), the sling capacity is 1.73 × the single-leg WLL; at 45° it is 1.41 ×; at 30° from horizontal only 1.0 ×. Choke hitches reduce the WLL by 20 %.

About Lifting Chain

Grade 80 and Grade 100 chains are quenched and tempered alloy steel with a 4:1 design factor: the minimum breaking force is four times the WLL. Grade 100 has 25 % higher strength in the same size, so a lighter chain can do the same job, but all fittings (hooks, master links, couplers) must be rated for the same grade. Metric grade 10 ratings differ slightly between makers: European RUD/pewag tables (used here) give 1.4 t for 6 mm and 6.7 t for 13 mm, US-made ASTM A973 metric chain 1.5 t and 6.8 t.

Inspect chain slings before each use and at least yearly by a competent person (ASME B30.9, EN 818-6). Retire a chain when the link diameter is worn by more than 10 % (EN 818-6) or the maker's limit (ASME tables give wear limits per size), when a link is stretched (pitch growth above about 3–5 %), nicked, bent, cracked or heat-damaged, or when the grade marking cannot be read.

Alloy lifting chain loses strength above about 400 °F (200 °C). Makers' tables reduce the WLL in steps above that temperature, and chain heated above about 1,000 °F (540 °C) must be scrapped. Do not galvanize or plate Grade 80/100 chain after manufacture: hydrogen embrittlement can make it brittle.

Questions

What is the WLL of 3/8 grade 80 chain?

7,100 lb (3.2 t) single leg, straight pull. Grade 100 of the same size is rated 8,800 lb. Metric 10 mm EN 818-2 grade 8 chain is rated 3.15 t.

What is the difference between grade 80 and grade 100 chain?

Grade 100 is about 25 % stronger for the same size: 1/2 in Grade 80 is rated 12,000 lb, Grade 100 15,000 lb. Both have a 4:1 design factor. Use only fittings of the same or higher grade.

Can I use grade 70 transport chain for lifting?

No. Grade 70 (gold chromate) is for cargo tie-downs only. Only alloy chain of Grade 80, 100 or 120, marked as lifting chain, may be used for overhead lifting.

How do I calculate the capacity of a two-leg chain sling?

Multiply the single-leg WLL by 2 × the sine of the sling angle from horizontal: 1.73 at 60°, 1.41 at 45°, 1.0 at 30°. A two-leg 3/8 Grade 80 sling at 60° is rated 7,100 × 1.73 ≈ 12,300 lb.

What does the 8 or T on a chain link mean?

Grade 8 (Grade 80) alloy lifting chain to EN 818-2 or ASTM A391. T refers to the tolerance class in EN 818. 10 or 100 marks Grade 100.

Sources

  1. EN 818-2: Short link chain for lifting purposes, medium tolerance chain for chain slings, grade 8
  2. ASTM A391/A391M: Grade 80 Alloy Steel Chain; ASTM A973/A973M: Grade 100 Alloy Steel Chain
  3. NACM: Welded Steel Chain Specifications (working load limits)
  4. Peerless Chain: Grade 80 / 100 working load limits
  5. Brindley Chains: LINX-8 grade 8 load chain EN 818-2 table
  6. RUD: VIP grade 100 chain load tables

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.