Neodymium Magnet Grades Chart (N35–N52, M, H, SH, UH, EH)

A neodymium magnet grade such as N42SH has two parts: the number is the minimum energy product in MGOe (here about 40–43 MGOe), the letters the coercivity class, which sets how hot the magnet may run (SH: about 150 °C). Higher numbers are stronger; more letters mean more heat resistance. No grade is both at once.

39 gradesChecked 2026-11-154 sources
grade number = (BH)max in MGOe2830333538404245485052N80 °CN35N38N40N42N45N48N50N52M100 °CN35MN38MN40MN42MN45MN48MN50MH120 °CN35HN38HN40HN42HN45HN48HSH150 °CN35SHN38SHN40SHN42SHN45SHUH180 °CN28UHN30UHN33UHN35UHN38UHN40UHEH200 °CN28EHN30EHN33EHN35EHN38EHclassHigher temperature classes stop at lower grade numbers.
Filled cells are standard grades; stronger colour = higher energy product. Tap a cell for its properties.Proportions shown, not to scale

Grade chartTap a grade for its properties and demagnetization curve

39 of 39
GradeBrRemanenceTkG(BH)maxMax. energy productkJ/m³MGOeHcJIntrinsic coercivity (min.)kA/mkOeTmaxMax. working temp. (typical)°C°F
N: standard (HcJ ≥ 11–12 kOe, 80 °C)
N351.17–1.2211.7–12.2263–28633–369551280176
N381.22–1.2512.2–12.5286–31036–399551280176
N401.25–1.2812.5–12.8302–32638–419551280176
N421.28–1.3212.8–13.2318–34240–439551280176
N451.32–1.3813.2–13.8342–36643–469551280176
N481.38–1.4213.8–14.2366–39046–499551280176
N501.40–1.4514–14.5382–40648–518751180176
N521.43–1.4814.3–14.8398–42250–538751180176
M: HcJ ≥ 14 kOe, 100 °C
N35M1.17–1.2211.7–12.2263–28633–36111414100212
N38M1.22–1.2512.2–12.5286–31036–39111414100212
N40M1.25–1.2812.5–12.8302–32638–41111414100212
N42M1.28–1.3212.8–13.2318–34240–43111414100212
N45M1.32–1.3813.2–13.8342–36643–46111414100212
N48M1.38–1.4213.8–14.2366–39046–49111414100212
N50M1.40–1.4514–14.5382–40648–51111414100212
H: HcJ ≥ 17 kOe, 120 °C
N35H1.17–1.2211.7–12.2263–28633–36135317120248
N38H1.22–1.2512.2–12.5286–31036–39135317120248
N40H1.25–1.2812.5–12.8302–32638–41135317120248
N42H1.28–1.3212.8–13.2318–34240–43135317120248
N45H1.32–1.3813.2–13.8342–36643–46135317120248
N48H1.38–1.4213.8–14.2366–39046–49135317120248
SH: HcJ ≥ 20 kOe, 150 °C
N35SH1.17–1.2211.7–12.2263–28633–36159220150302
N38SH1.22–1.2512.2–12.5286–31036–39159220150302
N40SH1.25–1.2812.5–12.8302–32638–41159220150302
N42SH1.28–1.3212.8–13.2318–34240–43159220150302
N45SH1.32–1.3813.2–13.8342–36643–46159220150302
UH: HcJ ≥ 25 kOe, 180 °C
N28UH1.04–1.0810.4–10.8207–23126–29198925180356
N30UH1.08–1.1310.8–11.3223–24728–31198925180356
N33UH1.13–1.1711.3–11.7247–27131–34198925180356
N35UH1.17–1.2211.7–12.2263–28633–36198925180356
N38UH1.22–1.2512.2–12.5286–31036–39198925180356
N40UH1.25–1.2812.5–12.8302–32638–41198925180356
EH: HcJ ≥ 30 kOe, 200 °C
N28EH1.04–1.0810.4–10.8207–23126–29238730200392
N30EH1.08–1.1310.8–11.3223–24728–31238730200392
N33EH1.13–1.1711.3–11.7247–27131–34238730200392
N35EH1.17–1.2211.7–12.2263–28633–36238730200392
N38EH1.22–1.2512.2–12.5286–31036–39238730200392
Hard ferrite (ceramic)
Ferrite C50.383.8273.41992.5250482
Ferrite C80.393.85283.52433.05250482

How to read a magnet grade

N stands for sintered neodymium-iron-boron. The number is the nominal maximum energy product (BH)max in MGOe, taken as the bottom of its range. N42 means 40–43 MGOe (318–342 kJ/m³) in the usual grade table. The suffix is the coercivity class: none, M, H, SH, UH, EH, in rising order of intrinsic coercivity HcJ and therefore of temperature resistance.

Br (remanence) is the flux density the material keeps after magnetization, in tesla or kilogauss. It decides how strong the magnet is: holding force scales roughly with Br², so an N52 (Br ≥ 1.43 T) holds about 50 % more than an N35 (Br ≥ 1.17 T) of the same size. HcJ (intrinsic coercivity) is the reverse field the material withstands before it starts to lose its magnetization. It measures resistance to heat and opposing fields. (BH)max combines both into one figure of merit.

Values are given in CGS units (kG, kOe, MGOe) in most catalogues and in SI units (T, kA/m, kJ/m³) in standards; the unit switch converts them. 1 T = 10 kG, 1 kOe = 79.58 kA/m, 1 MGOe = 7.96 kJ/m³.

About Magnet Grades

Sintered NdFeB is the strongest permanent magnet material in production. Every grade is a compromise between remanence and coercivity: adding heavy rare earths (dysprosium, terbium) raises HcJ and the usable temperature but lowers Br. That is why N52 exists only in the plain N and M classes, while the EH class tops out at about N38.

The ranges in the chart are the common industry grade table that Chinese, Japanese and Western producers publish (the GB/T 13560 grade structure; IEC 60404-8-1 lists the same materials under its own codes). Producers differ slightly at the edges (some sell N52 with Br up to 1.48 T, some N48 with HcJ ≥ 11 kOe and some N50 with ≥ 12 kOe), so take design values from your supplier's data sheet. Normal coercivity HcB is not listed for the same reason: published minimums for the same grade vary between producers.

The max. working temperature is the usual catalogue figure for a magnet with a permeance coefficient of about 1–2 (a moderately thick magnet). A thin disc magnetized through its thickness self-demagnetizes more strongly and loses flux at a lower temperature; a magnet in a closed steel circuit can run hotter. Br falls by about 0.11–0.12 % per kelvin for NdFeB, reversibly, until the knee of the curve is crossed. Beyond that point the loss is permanent.

Ferrite and samarium cobalt

Hard ferrite (ceramic) magnets have about a third of the remanence of NdFeB (Br ≈ 0.38–0.40 T) and a tenth of the energy product, but are cheap, do not corrode and keep working to 250 °C. Their coercivity rises with temperature, so they are at risk of demagnetization in the cold rather than the heat. C5 and C8 are the common MMPA grades; Chinese grade names such as Y30 and Y30BH are similar materials.

Samarium cobalt (SmCo5 and Sm2Co17) reaches energy products of about 16–32 MGOe, works to 250–350 °C with very low temperature coefficients and needs no coating. It is the choice for high temperatures and precision sensors; grade tables differ by producer and are not listed here.

Coating

NdFeB corrodes quickly in humid air. Standard coatings are nickel (Ni-Cu-Ni triple layer), zinc and epoxy; the coating does not change the grade but adds thickness, so check it when the magnet must fit a pocket.

Questions

How strong is an N52 magnet?

N52 has a remanence of 1.43–1.48 T (14.3–14.8 kG) and an energy product of 50–53 MGOe (398–422 kJ/m³). For the same size it holds roughly 50 % more than N35. Its HcJ is only ≥ 11 kOe (875 kA/m), so it is limited to about 80 °C, less in thin shapes.

What is the difference between N42 and N52?

N52 has about 12 % higher remanence (1.43 vs 1.28 T minimum) and about 25 % more energy product. Holding force for the same size is roughly 25 % higher. N52 costs more and tolerates less heat.

What do the letters after the grade mean (M, H, SH, UH, EH)?

The coercivity class: minimum HcJ of 14, 17, 20, 25 and 30 kOe, for typical maximum working temperatures of about 100, 120, 150, 180 and 200 °C. Plain N grades: HcJ ≥ 12 kOe (≥ 11 kOe for N50 and N52), about 80 °C.

At what temperature do neodymium magnets lose their magnetism?

Above the grade's maximum working temperature the magnet starts to lose flux permanently: about 80 °C for N grades up to 200 °C for EH. The Curie temperature, where all magnetism is gone, is around 310–340 °C for NdFeB.

How do I convert kG, kOe and MGOe to SI units?

1 kG = 0.1 T; 1 kOe = 79.58 kA/m; 1 MGOe = 7.958 kJ/m³. N42: Br 12.8–13.2 kG = 1.28–1.32 T; (BH)max 40–43 MGOe = 318–342 kJ/m³.

Sources

  1. IEC 60404-8-1:2015, Magnetic materials, Part 8-1: Specifications for individual materials, Magnetically hard materials
  2. GB/T 13560-2017: Sintered neodymium iron boron permanent magnets (grade structure)
  3. MMPA Standard 0100-00: Standard specifications for permanent magnet materials (ferrite C5, C8)
  4. Arnold Magnetic Technologies: Neodymium and ferrite magnet grade data sheets

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.