Rebar Size Chart: US #3–#18, Metric and Canadian Bars

Nominal diameter, cross-sectional area and weight of reinforcing bars in the three systems used in North America and worldwide. Up to #8, a US bar number is the diameter in eighths of an inch. A #4 bar is 4/8 = 1/2 in (12.7 mm).

31 sizesChecked 2026-11-154 sources
US bars (ASTM A615)#3#4#5#6#7#8#9#10#11#14#18Metric bars, mm (EN 10080)6810121416202528324050
Nominal cross-sections, one scale for both rows. US #3–#18 and metric Ø6–Ø50 mm.Drawn to scale · Dimensions in mmDimensions in inches

Size chartTap a size for its drawing and full specs

31 of 31
BardNominal diametermminmm · inANominal areamm²in²mm² · in²Nominal weightkg/mlb/ftkg/m · lb/ftSoft-metric size (A615M)
US inch-pound bars, ASTM A615 / A706
#39.50.375710.1100.5600.376#10
#412.70.5001290.2000.9940.668#13
#515.90.6252000.3101.5521.043#16
#619.10.750283.90.4402.2351.502#19
#722.20.875387.10.6003.0422.044#22
#825.41.000509.70.7903.9732.670#25
#928.71.128645.21.0005.0603.400#29
#1032.31.270819.41.2706.4044.303#32
#1135.81.4101006.51.5607.9075.313#36
#14431.6931451.62.25011.3857.650#43
#1857.32.2572580.64.00020.23913.600#57
Metric bars, EN 10080 / ISO 6935-2
Ø660.23628.30.0440.2220.149—
Ø880.31550.30.0780.3950.265—
Ø10100.39478.50.1220.6170.415—
Ø12120.4721130.1750.8880.597—
Ø14140.5511540.2391.2100.813—
Ø16160.6302010.3121.5801.062—
Ø20200.7873140.4872.4701.660—
Ø25250.9844910.7613.8502.587—
Ø28281.1026160.9554.8303.246—
Ø32321.2608041.2466.3104.240—
Ø40401.57512571.9489.8606.626—
Ø50501.96919633.04315.40010.348—
Canadian metric bars, CSA G30.18
10M11.30.4451000.1550.7850.527—
15M160.6302000.3101.5701.055—
20M19.50.7683000.4652.3551.582—
25M25.20.9925000.7753.9252.637—
30M29.91.1777001.0855.4953.692—
35M35.71.40610001.5507.8505.275—
45M43.71.72015002.32511.7757.912—
55M56.42.22025003.87519.62513.187—

How rebar sizes are named

US bars are designated by number. From #3 to #8 the number is the nominal diameter in eighths of an inch: #3 = 3/8 in, #5 = 5/8 in, #8 = 1 in. From #9 up the bars are sized by area instead (#9 has 1.00 in², #10 1.27 in², #11 1.56 in²), so the diameters (1.128, 1.270, 1.410 in) no longer match the number. #14 and #18 are large bars for columns and heavy foundations.

The same bars are marked in soft metric under ASTM A615M: #4 is "13", #5 is "16", #8 is "25". The number is the diameter rounded to whole millimetres. The steel is identical; only the label differs.

Metric bars (Europe, Asia, most of the world) are named by nominal diameter in millimetres: Ø12, Ø16, Ø20. Canadian bars use a different series named 10M, 15M … 55M, where the number is roughly the diameter but the real diameter is 11.3, 16.0, 19.5 … mm and areas are round numbers (100, 200, 300 mm²).

Nominal diameter is the diameter of a plain round bar with the same mass per length. The ribs (deformations) make the outer diameter about 5–15 % larger, so a caliper across the ribs reads more than the chart.

About Rebar Sizes

Weights follow from the area and a steel density of 7850 kg/m³ (490 lb/ft³): mass per metre = 0.00785 × area in mm². US bar weight in lb/ft is about 3.4 × the area in in². These are nominal values; the standards allow a mass deviation of about −6 % per bar (ASTM A615) or ±4.5–6 % (EN 10080, depending on size).

To identify a bar on site, read the rolled-on marks: on US bars the producer letter, the size number (or soft-metric number), the type of steel (S for A615 carbon steel, W for A706 weldable) and a grade mark (60, 80, or a number of lines). European bars carry a rib pattern that identifies the mill and the grade class (B500B, B500C).

Grade (yield strength) does not change the size. US Grade 60 means 60 ksi (420 MPa) minimum yield; European B500 means 500 MPa characteristic yield strength. Strength is set by the designer: a #5 of Grade 40 and one of Grade 80 have the same 0.31 in² area.

Substituting bars between systems

Bars in different systems are never exactly equal. Substitute by area, never by name: a #5 bar (200 mm²) is nearly the same as a Canadian 15M (200 mm²) and close to a metric Ø16 (201 mm²); a #4 (129 mm²) is a bit larger than Ø12 (113 mm²). Spacing, cover and development length must be checked again after any substitution.

Questions

What size is #4 rebar?

1/2 in (12.7 mm) nominal diameter, 0.20 in² (129 mm²) area, 0.668 lb/ft (0.994 kg/m). Its soft-metric designation is 13.

How do you tell the diameter from the rebar number?

For #3 to #8, divide the number by 8 to get inches: #6 = 6/8 = 3/4 in. Above #8 that rule no longer holds: #9 is 1.128 in, #10 1.270 in, #11 1.410 in.

How much does rebar weigh per foot?

#3 0.376, #4 0.668, #5 1.043, #6 1.502, #7 2.044, #8 2.670, #9 3.400, #10 4.303, #11 5.313 lb/ft. Metric: Ø10 0.617, Ø12 0.888, Ø16 1.58, Ø20 2.47 kg/m.

Is 12 mm rebar the same as #4?

No. #4 is 12.7 mm (129 mm²); Ø12 is 113 mm², about 12 % less steel. They are often treated as alternatives, but only after checking the design by area.

What is the difference between 10M and #3 rebar?

10M (Canada) is 11.3 mm and 100 mm²; #3 (US) is 9.5 mm and 71 mm². 10M is closer to a #3½, between #3 and #4.

Sources

  1. ASTM A615/A615M: Deformed and plain carbon-steel bars for concrete reinforcement (Table 1, bar designations)
  2. CRSI: Concrete Reinforcing Steel Institute, ASTM standard reinforcing bars
  3. EN 10080:2005 / ISO 6935-2: Steel for the reinforcement of concrete, nominal sizes and masses
  4. CSA G30.18: Carbon steel bars for concrete reinforcement (metric bar designations)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.