Screwdriver Bit Size Chart: Phillips, Pozidriv, Slotted, Square

Cross-recess bits are numbered by recess size, not by screw length: PH2 and PZ2 fit M3.5–M5 and #5–#9 screws, by far the most common size. Phillips and Pozidriv look alike but are not interchangeable; Pozidriv screws have four extra radial marks between the arms of the cross.

32 sizesChecked 2026-11-158 sources
PhillipsPozidrivSlottedSquareHexTorxTri-wingSpanner
Recess shapes seen from above (schematic, not to scale). Phillips and Pozidriv differ by the extra radial ticks; Torx and hex have parallel flanks and do not cam out.Proportions shown, not to scale

Size chartSort by any column, or filter to find a row

32 of 32
SizeMetric screws (ISO 7045 / slot width)Wood screw gauge (typical)Color codeHandle coloraBlade thicknessmminmm · inbBlade widthmminmm · inTest torque (ISO 2380)N·mlb·ftN·m · lb·ftsHex shank across flatsmminmm · inShank form
Phillips (cross recess type H)
PH0M1.6, M2#0, #1———————
PH1M2.5, M3#2–#4———————
PH2M3.5, M4, M5#5–#9———————
PH3M6#10–#16———————
PH4M8, M10#18–#24———————
Pozidriv (cross recess type Z)
PZ0M1.6, M2#0, #1———————
PZ1M2.5, M3#2–#4———————
PZ2M3.5, M4, M5#5–#9———————
PZ3M6#10–#16———————
PZ4M8, M10#18–#24———————
Slotted blades, thickness × width in mm (ISO 2380)
0.4 × 2————0.40.01620.0790.30.2——
0.4 × 2.5————0.40.0162.50.0980.40.3——
0.5 × 3————0.50.02030.1180.70.5——
0.6 × 3————0.60.02430.1181.10.8——
0.6 × 3.5————0.60.0243.50.1381.31.0——
0.8 × 4————0.80.03140.1572.61.9——
1 × 4.5————10.0394.50.1774.53.3——
1 × 5.5————10.0395.50.2175.54.1——
1.2 × 6.5————1.20.0476.50.2569.57.0——
1.2 × 8————1.20.04780.31511.58.5——
1.6 × 8————1.60.06380.31520.515.1——
1.6 × 10————1.60.063100.39425.618.9——
2 × 12————20.079120.4724835.4——
2.5 × 14————2.50.098140.55187.564.5——
Robertson / square drive
#00 square—#1, #2Orange#FF8C00—————
#0 square—#3, #4Yellow#F2C200—————
#1 square—#5–#7Green#2E8B3A—————
#2 square—#8–#10Red#C8102E—————
#3 square—#12, 1/4″Black#1A1A1A—————
Hex bit shanks (ISO 1173)
C6.3———————6.351/4Plain hex, for bit holders (insert bit, usually 25 mm long)
E6.3———————6.351/4Hex with ball groove, for quick-change chucks (power bit, 50 mm and longer)
C8———————7.940.313Plain hex, for bit holders (insert bit, usually 25 mm long)

How to identify the drive and pick the bit

Phillips (PH): a plain cross with rounded, tapered flanks. Pozidriv (PZ): a cross with four fine lines (ticks) at 45° on the head, and a square-ish centre. A PH bit in a PZ screw rocks and cams out; a PZ bit in a PH screw sits on its corners and chews the recess. European construction and furniture screws are mostly PZ, US screws mostly PH.

Fit test: the right bit stands upright in the recess without support and fills it to the bottom. One size too small wobbles; one size too big does not reach the bottom and slips at the first turn.

Slotted: the blade should fill the slot length and its thickness should match the slot width. A blade narrower than the slot twists out; one wider than the head scars the part around a countersunk screw.

Square (Robertson): sized #00 to #3, and the handle color tells the size. #2 (red) drives most #8–#10 deck and construction screws in North America.

Torx and Torx Plus have their own chart; see Torx sizes. Hex socket screws take hex keys or hex bits; see hex key sizes.

About Screwdriver Bits

Bits wear. A rounded PH2 cams out on a screw it used to drive; replace it before it ruins the recess. Impact-rated bits (usually black, with a torsion zone in the shank) last far longer in impact drivers than standard bits.

Below PH0 there are PH00 and PH000 for eyeglass, watch and electronics screws smaller than M1.6. They are not assigned to screw sizes in ISO 7045, so they are not in the table; precision screwdriver sets include them.

The shank matters as much as the tip. A C6.3 insert bit (1/4 in hex, 25 mm long) goes into a magnetic bit holder or a screwdriver handle. An E6.3 power bit has a ball groove near the drive end and locks into the quick-change chuck of drills and impact drivers. Both have the same 1/4 in hex (6.35 mm across flats), so a C6.3 bit also fits an E6.3 chuck if a holder is used. Heavy impact drivers sometimes take 5/16 in (C8) bits.

Two less common security drives: tri-wing (three slotted wings, found on electronics and aircraft panels) and spanner or 'snake-eye' (two holes, on public fixtures and elevators). Their sizes are not standardised across makers; buy bits from the screw maker's own range when possible.

Phillips, Pozidriv, JIS: three crosses

Japanese cross-recess screws (JIS B 1012, marked with a single dot on the head) have a shallower cam-out angle than Phillips. A JIS bit drives both JIS and Phillips screws well; a Phillips bit tends to cam out in JIS screws on cameras, motorcycles and electronics. The sizes are numbered the same way (JIS 0, 1, 2, 3).

Cam-out in Phillips was partly intended: the bit slips before the screw is overtightened. Pozidriv's parallel flanks were designed to transmit more torque without slipping.

DriveHead markingCommon inBit to use
Phillips PHPlain crossUS screws, drywall screws, electrical devicesPH
Pozidriv PZCross with 4 ticksEuropean wood, chipboard and machine screwsPZ
JIS crossCross with one dotJapanese equipmentJIS (PH works poorly)
Combination slot/crossCross with slotElectrical terminals, switchgearPZ/slotted combo (FL/PZ) or PH/slotted

Questions

What size Phillips bit is the most common?

PH2. It fits M3.5–M5 machine screws and #5–#9 wood and drywall screws. PH1 covers M2.5–M3 and #2–#4, PH3 covers M6 and #10–#16.

Can I use a Phillips bit on a Pozidriv screw?

It turns, but it contacts the recess only at points and cams out under load. Use PZ bits on screws with the four tick marks; it matters most on long wood and chipboard screws.

What color is a #2 Robertson bit?

Red. #00 is orange, #0 yellow, #1 green, #2 red and #3 black. #2 fits #8–#10 screws, #3 fits #12 and 1/4 in.

What is the difference between C6.3 and E6.3 bits?

Both have a 1/4 in (6.35 mm) hex shank. C6.3 is a plain insert bit, typically 25 mm long, for bit holders; E6.3 has a ball groove and is long enough (50 mm and up) to lock directly in a quick-change chuck.

Sources

  1. ISO 7045:2011, Pan head screws with type H or type Z cross recess (recess number per thread size)
  2. ISO 4757:1983, Cross recesses for screws
  3. ISO 8764-1: Assembly tools for screws and nuts, Screwdriver bits for cross-recessed head screws
  4. ISO 2380-1: Assembly tools for screws and nuts, Screwdrivers for slotted-head screws
  5. ISO 1173:2001, Drive ends for hand- and machine-operated screwdriver bits and connecting parts
  6. Wikipedia: List of screw drives (Phillips sizes, ISO 2380 slotted table)
  7. Wikipedia: Robertson screw (size and colour table)
  8. EJOT: Cross recess / hexagon drive bit form C 6.3 (catalogue)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.