Socket Drive Size Chart: 1/4, 3/8, 1/2, 3/4 and 1 inch

The drive size is the square that connects ratchet, extension and socket. It is an inch size everywhere (metric sockets use it too), and ISO 1174 names the same squares 6.3, 10, 12.5, 20 and 25 mm. Pick the drive by torque: 1/2 inch covers wheel nuts and most car work, 3/8 inch the engine bay, 1/4 inch small fasteners.

5 drive sizesChecked 2026-11-154 sources
The five common drive squares drawn to the same scale. Each step roughly doubles the torque capacity.Drawn to scale

Size chartTap a size for its drawing and full specs

5 of 5
DrivesDrive square (across flats)mminISO 1174 sizeMetric sockets (typical range)SAE sockets (typical range)Torque wrench range (typical)N·mlb·ft
1/4″ drive6.351/46.3———
3/8″ drive9.523/810———
1/2″ drive12.701/212.5———
3/4″ drive19.053/420———
1″ drive25.40125———

How to tell the drive size

Measure across the flats of the male square on the ratchet or extension: about 6.3 mm = 1/4 in, 9.5 mm = 3/8 in, 12.7 mm = 1/2 in, 19 mm = 3/4 in, 25.4 mm = 1 in. The socket's hole is a few hundredths larger. Sockets are often stamped with the drive size and the hex size, for example 1/2" 19 mm.

The ISO number (12.5 for 1/2 in) is only a name; it is not a different metric square. A '12.5 mm' socket fits every 1/2 in ratchet.

Adapters step one size up or down (3/8 in female to 1/2 in male, and so on). Stepping up to drive a large socket from a small ratchet is fine for light torque; stepping down from a large wrench onto a small socket will snap the small square first.

About Socket Drive Sizes

The square size is set by the torque the drive square can carry without twisting off. Small drives are shorter and fit in tight spaces; large drives carry more torque but the socket walls and the head of the ratchet get bulky.

Impact sockets are made of chrome-molybdenum steel with thicker walls, a black oxide or phosphate finish and a cross hole for a retaining pin. Hand sockets are usually chrome-vanadium, chrome plated and thinner walled. Never put a hand socket on an impact wrench: the hardened, thin wall can crack and fly apart.

Impact wrenches hold the socket with a friction ring (hog ring), a detent pin, or a pin and O-ring through the cross hole. The anvil square follows ISO 1174-2 and has the same nominal sizes. Very large industrial impact wrenches use 1-1/2 in square drives or the #5 spline drive, which has no square at all.

Six-point sockets grip the flats of a hex and are the right choice for tight or rusted fasteners; twelve-point sockets index more easily in tight spaces but load the corners and round them off sooner.

Which drive for which job

Orientation, based on common tightening torques. Check the torque value of your fastener and choose a drive with headroom.

DriveTypical jobs
1/4 inElectronics, interior trim, small engine and bicycle bolts, M4–M8
3/8 inEngine bay, spark plugs, brake calipers on small cars, M6–M14
1/2 inWheel nuts, suspension, axle nuts on cars, M10–M20
3/4 inTrucks, tractors, construction equipment, M20–M30
1 inHeavy trucks, mining and industrial bolting, M30 and up

Questions

What size is a 1/2 inch drive square in mm?

12.70 mm across the flats (ISO 1174 calls it size 12.5). 3/8 in is 9.53 mm (size 10), 1/4 in is 6.35 mm (size 6.3).

Do metric sockets use metric drive squares?

No. Metric sockets use the same inch squares; only the hex opening is metric. A 13 mm socket with a 3/8 in drive fits any 3/8 in ratchet.

Can I use regular sockets on an impact wrench?

No. Use impact sockets: they are Cr-Mo steel with thicker walls and are designed for the hammering load. Chrome hand sockets can crack.

What is the strongest common drive size?

1 in square drive in normal tool sets; industrial bolting goes to 1-1/2 in square or #5 spline drives.

Sources

  1. ISO 1174-1:1996, Assembly tools for screws and nuts, Driving squares, Part 1: Driving squares for hand socket tools
  2. ISO 1174-2:1996, Driving squares, Part 2: Driving squares for power socket tools
  3. ASME B107.4: Driving and spindle ends for portable hand, impact, air, and electric tools
  4. ASME B107.110: Socket wrenches, hand (inch and metric series)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.