Wood Screw Size Chart: Gauge, Diameter and Pilot Holes

Inch wood screws are sized by gauge: the diameter in inches is 0.060 + 0.013 × gauge, so a #8 is 0.164 in (4.2 mm). Drill a pilot hole about the size of the thread root (1/8 in in hardwood, 3/32 in in softwood for a #8) and a clearance hole of 11/64 in through the top board.

17 sizesChecked 2026-11-155 sources

Size chartTap a size for its drawing and full specs

17 of 17
SizedMajor diametermminmm · indkFlat head diameter (max)mminmm · inClearance (shank) holemminmm · inPilot hole, hardwood (typical)mminmm · inPilot hole, softwood (typical)mminmm · inDrive (typical)
Inch gauge wood screws (ASME B18.6.1)
#22.180.0864.40.172—1.61/161.23/64—
#32.510.0995.10.199—25/641.61/16—
#42.840.1125.70.2253.21/825/641.61/16—
#53.180.1256.40.252—2.43/3225/64—
#63.510.1387.10.2793.69/642.43/3225/64—
#73.840.1517.70.305—2.87/642.43/32—
#84.170.1648.40.3324.411/643.21/82.43/32—
#94.50.1779.10.358—3.21/82.87/64—
#104.830.1909.80.3855.213/643.21/82.87/64—
#125.490.21611.10.4385.67/323.69/643.21/8—
#146.150.24212.50.4916.41/445/323.69/64—
Metric wood / chipboard screws (typical)
3.0 mm30.11860.236———PZ1 / T10
3.5 mm3.50.13870.276———PZ2 / T15
4.0 mm40.15780.315———PZ2 / T20
4.5 mm4.50.17790.354———PZ2 / T20
5.0 mm50.197100.394———PZ2 / T25
6.0 mm60.236120.472———PZ3 / T30

How to drill for a wood screw

Drill a clearance hole through the piece you are fastening, so the screw pulls it tight instead of jacking the boards apart. Then drill a pilot hole into the piece that receives the thread: hardwood needs a pilot close to the root diameter, softwood a smaller one. Test in a scrap first: densities vary, and tapered pilot bits give different sizes from straight bits.

The pilot and clearance holes in the chart are typical shop values; published charts disagree by 1/64 in. The head diameter is the ASME B18.6.1 maximum for flat (countersunk, 82°) heads; oval heads are the same diameter, pan and round heads differ.

Inch wood screws are named gauge × length: #8 × 1-1/4 is 0.164 in diameter, 1-1/4 in long (flat heads are measured overall, round and pan heads under the head). Metric wood screws are named diameter × length in mm: 4 × 40.

About Wood Screws

The gauge number is not a dimension but maps to one: every gauge step adds 0.013 in. #6, #8 and #10 cover most furniture and construction work; #12 and #14 are for heavy hinges and structural fixing. The same gauge numbers apply to sheet-metal screws, which have the same major diameters but a different thread.

Modern construction and deck screws (and European chipboard screws) are often thinner-shanked, hardened and self-drilling with Torx or Pozidriv drives. Pilot holes are still advisable in hardwood and near board ends.

Metric values in the second group are typical: there is no dimensional standard for chipboard screw heads, but most makers use a head of about twice the thread diameter and the drives listed.

Questions

What size pilot hole for a #8 wood screw?

About 1/8 in (3.2 mm) in hardwood and 3/32 in (2.4 mm) in softwood. The clearance hole in the top board is 11/64 in (4.4 mm).

What is the diameter of a #10 screw?

0.190 in, 4.83 mm. Gauge diameter = 0.060 + 0.013 × gauge.

Is a #8 screw the same as 4 mm?

Close: #8 is 4.17 mm. A 4 mm metric wood screw is a fair substitute; a 4.5 mm screw is slightly thicker.

What size pilot hole for a #10 screw in softwood?

Typically 7/64 in (2.8 mm); in hardwood 1/8 in (3.2 mm).

Sources

  1. ASME B18.6.1: Wood screws (inch series)
  2. McFeely's: Drilling chart for screw sizes
  3. Misumi: Pilot hole sizes for wood screws
  4. HandySkook: Wood screw size chart (gauge, diameter, pilot holes)
  5. EN 14592: Timber structures, dowel-type fasteners (metric wood screws, performance)

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.