Spark Plug Size Chart: Thread, Hex, Reach and Seat Type

A spark plug is identified by thread diameter (8, 10, 12, 14 or 18 mm), seat (flat with a gasket, or tapered), reach (thread length) and hex for the socket. The most common car plug is 14 mm × 1.25 with a 5/8 in (16 mm) hex; modern engines increasingly use 12 mm plugs with a 14 mm hex.

7 sizesChecked 2026-11-155 sources
8 mmFlat with gasket10 mmFlat with gasket12 mmFlat with gasket14 mmFlat with gasket14 mmTapered (no gasket)18 mmFlat with gasket18 mmTapered (no gasket)
Thread diameter, a typical reach and the common hex for each size, to one scale. Simplified outlines.Drawn to scale

Size chartSort by any column, or filter to find a row

7 of 7
ThreadPThread pitchmminSeatHex (socket size)Reach optionsTypical engines
Flat (gasket) seat
8 mm (M8 × 1.0)10.0394Flat with gasket13 mm9.5 mm (3/8 in)model engines, small 2-stroke tools, some motorcycles
10 mm (M10 × 1.0)10.0394Flat with gasket16 mm (5/8 in); 12 mm on thin-wall plugs12.7 mm (1/2 in), 19 mm (3/4 in)motorcycles, scooters, small engines, some modern car engines
12 mm (M12 × 1.25)1.250.0492Flat with gasket14 mm, 16 mm (5/8 in), 17.5 mm19 mm (3/4 in), 26.5 mm (1.04 in)modern 4-valve car engines (compact heads, direct injection), motorcycles
14 mm (M14 × 1.25) gasket seat1.250.0492Flat with gasket16 mm (5/8 in), 20.6 mm (13/16 in); 21 mm on older European plugs9.5 mm (3/8 in), 12.7 mm (1/2 in), 19 mm (3/4 in), 26.5 mmmost cars worldwide since the 1960s, lawn mowers and small engines (3/8 in reach)
18 mm (M18 × 1.5) gasket seat1.50.0591Flat with gasket20.6 mm (13/16 in); 24 or 21 mm in Europe12.7 mm (1/2 in), 19 mm (3/4 in)older cars, aircraft piston engines (5/8-24 shielded types differ), stationary engines
Tapered (conical) seat
14 mm (M14 × 1.25) tapered seat1.250.0492Tapered (no gasket)16 mm (5/8 in)11.7 mm (0.460 in), 18 mm (0.708 in)GM V8s (small-block Chevy, LS), many Ford and Chrysler engines
18 mm (M18 × 1.5) tapered seat1.50.0591Tapered (no gasket)20.6 mm (13/16 in)about 11–12 mm (0.438 in typical; short reach, tapered)older Ford V8s and industrial engines

Thread, seat, reach and hex

Thread: all automotive spark plugs use metric threads: M10 × 1.0, M12 × 1.25, M14 × 1.25 or M18 × 1.5. Seat: a flat seat seals with a crush gasket (a washer folded into the plug), a tapered seat seals on a conical face without a gasket. Never put a gasket on a tapered plug or fit a flat-seat plug in a tapered hole.

Reach is the length of the threaded part from the seat to the end of the thread. It must match the head: too short and the thread in the head carbons up, too long and the plug sticks into the combustion chamber and can hit a valve or piston. Common reaches: 3/8 in (9.5 mm, small engines), 1/2 in (12.7 mm), 3/4 in (19 mm) and 26.5 mm (modern long-reach plugs); tapered seats 0.460 in (11.7 mm) and 0.708 in (18 mm).

Hex: 5/8 in (16 mm) and 13/16 in (20.6 mm; a 21 mm socket fits) are the classic socket sizes; 14 mm and 12 mm hexes on newer thin plugs. Use a spark plug socket with a rubber insert or magnet so the insulator is held and protected.

About Spark Plug Sizes

The plug's part number encodes everything: on an NGK BKR6E, B = 14 mm thread with 5/8 in hex, K = compact type, R = resistor, 6 = heat range, E = 19 mm reach. Denso, Bosch and Champion each use their own codes, so cross-reference by the engine maker's specification or the plug maker's cross-reference table, not by similar-looking codes.

Heat range describes how fast the plug's insulator tip sheds heat to the head. A hot plug (long insulator nose) burns off deposits at low load; a cold plug (short nose) resists pre-ignition at high load and in tuned engines. NGK and Denso numbers get colder as they rise; Champion and older Bosch numbers get hotter. Change only one step from the specified heat range unless you know why.

Torque new plugs to the maker's figure. As a guide for gasket-seat plugs in aluminum heads: M10 about 10–15 N·m, M12 15–20 N·m, M14 25–30 N·m, M18 35–40 N·m; tapered seats need less (M14 tapered about 10–20 N·m). Without a torque wrench, a new gasket plug is turned 1/2 to 2/3 turn past finger-tight, a tapered plug about 1/16 turn.

Reach, in inches and millimeters

Measure from the seat (gasket face or taper) to the end of the thread.

ReachmmSeatTypical
3/8 in9.5gasketsmall engines, mowers
0.460 in11.7taperedGM, Ford 14 mm tapered (short)
1/2 in12.7gasketolder cars, motorcycles
0.708 in18.0taperedGM LS and many later tapered-seat engines
3/4 in19.0gasketmost cars from the 1980s
1.04 in26.5gasketmodern 4-valve and direct-injection engines

Questions

What size socket is a spark plug?

5/8 in (16 mm) for most 14 mm and many 10 mm plugs, 13/16 in (20.6 mm) for older 14 mm and 18 mm plugs, and 14 mm for most 12 mm plugs. Use a spark plug socket with a rubber insert.

What thread is a spark plug?

Metric: M14 × 1.25 is the most common, then M12 × 1.25, M10 × 1.0 and M18 × 1.5.

What is spark plug reach?

The length of the threaded section from the seat to the end of the thread: typically 9.5, 12.7, 19 or 26.5 mm for gasket seats and 11.7 or 18 mm for tapered seats.

What is the difference between a gasket seat and a tapered seat plug?

A gasket-seat plug seals with a crushable washer on a flat face; a tapered-seat plug seals on a cone in the head and has no washer. They are not interchangeable.

Does a higher heat range number mean hotter?

With NGK and Denso, no: higher numbers are colder plugs. With Champion, higher numbers are hotter. Check the maker's chart.

Sources

  1. ISO 28741: Road vehicles, spark plugs and their cylinder head housings, basic characteristics and dimensions
  2. SAE J548: Spark plugs
  3. NGK Spark Plugs: Reading the part number (thread, hex, reach, heat range)
  4. Denso: Spark plug numbering system
  5. Champion: Spark plug catalogue: thread, seat and reach

Values last checked against these sources on November 15, 2026. · How we check data

Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.