H7/m6 Fit Tolerances
ISO Fits · Hole-basis fits (H hole)
H7/m6: Transition fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +21 / 0 µm, the shaft +21 / +8 µm, giving a maximum clearance of 13 µm and a minimum clearance of −21 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Transition
- Max. clearance at ⌀25 mm
- 13 µm0.00051 in0.00051 in13 µm
- Min. clearance at ⌀25 mm (− = interference)
- −21 µm−0.00083 in−0.00083 in−21 µm
Drawing
H7/m6 specifications
| Fit type | Transition |
|---|---|
| Hole limits at ⌀25 mm (µm) | +21 / 0 |
| Shaft limits at ⌀25 mm (µm) | +21 / +8 |
| Max. clearance at ⌀25 mm | 13 µm0.00051 in |
| Min. clearance at ⌀25 mm (− = interference) | −21 µm−0.00083 in |
H7/m6 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +10 / 0 | +8 / +2 | +8 | −8 | transition |
| 3–6 | +12 / 0 | +12 / +4 | +8 | −12 | transition |
| 6–10 | +15 / 0 | +15 / +6 | +9 | −15 | transition |
| 10–18 | +18 / 0 | +18 / +7 | +11 | −18 | transition |
| 18–30 | +21 / 0 | +21 / +8 | +13 | −21 | transition |
| 30–50 | +25 / 0 | +25 / +9 | +16 | −25 | transition |
| 50–80 | +30 / 0 | +30 / +11 | +19 | −30 | transition |
| 80–120 | +35 / 0 | +35 / +13 | +22 | −35 | transition |
| 120–180 | +40 / 0 | +40 / +15 | +25 | −40 | transition |
| 180–250 | +46 / 0 | +46 / +17 | +29 | −46 | transition |
| 250–315 | +52 / 0 | +52 / +20 | +32 | −52 | transition |
| 315–400 | +57 / 0 | +57 / +21 | +36 | −57 | transition |
| 400–500 | +63 / 0 | +63 / +23 | +40 | −63 | transition |
Transition fit, mostly tight: parts that must not loosen but can still be dismantled, bearing rings under heavier loads.
Other fits of the same type (Transition)
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.