K7/h6 Fit Tolerances
ISO Fits · Shaft-basis fits (h shaft)
K7/h6: Transition fit, Shaft-basis fits (h shaft). At ⌀25 mm the hole is +6 / −15 µm, the shaft 0 / −13 µm, giving a maximum clearance of 19 µm and a minimum clearance of −15 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Transition
- Max. clearance at ⌀25 mm
- 19 µm0.00075 in0.00075 in19 µm
- Min. clearance at ⌀25 mm (− = interference)
- −15 µm−0.00059 in−0.00059 in−15 µm
Drawing
K7/h6 specifications
| Fit type | Transition |
|---|---|
| Hole limits at ⌀25 mm (µm) | +6 / −15 |
| Shaft limits at ⌀25 mm (µm) | 0 / −13 |
| Max. clearance at ⌀25 mm | 19 µm0.00075 in |
| Min. clearance at ⌀25 mm (− = interference) | −15 µm−0.00059 in |
K7/h6 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | 0 / −10 | 0 / −6 | +6 | −10 | transition |
| 3–6 | +3 / −9 | 0 / −8 | +11 | −9 | transition |
| 6–10 | +5 / −10 | 0 / −9 | +14 | −10 | transition |
| 10–18 | +6 / −12 | 0 / −11 | +17 | −12 | transition |
| 18–30 | +6 / −15 | 0 / −13 | +19 | −15 | transition |
| 30–50 | +7 / −18 | 0 / −16 | +23 | −18 | transition |
| 50–80 | +9 / −21 | 0 / −19 | +28 | −21 | transition |
| 80–120 | +10 / −25 | 0 / −22 | +32 | −25 | transition |
| 120–180 | +12 / −28 | 0 / −25 | +37 | −28 | transition |
| 180–250 | +13 / −33 | 0 / −29 | +42 | −33 | transition |
| 250–315 | +16 / −36 | 0 / −32 | +48 | −36 | transition |
| 315–400 | +17 / −40 | 0 / −36 | +53 | −40 | transition |
| 400–500 | +18 / −45 | 0 / −40 | +58 | −45 | transition |
Shaft-basis transition fit: bearing outer rings or bushes in housings, located firmly but removable.
Other fits of the same type (Transition)
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.