H7/n6 Fit Tolerances
ISO Fits · Hole-basis fits (H hole)
H7/n6: Transition fit, Hole-basis fits (H hole). At ⌀25 mm the hole is +21 / 0 µm, the shaft +28 / +15 µm, giving a maximum clearance of 6 µm and a minimum clearance of −28 µm (negative = interference). The table below lists the limits for every ISO size range up to 500 mm.
- Fit type
- Transition
- Max. clearance at ⌀25 mm
- 6 µm0.00024 in0.00024 in6 µm
- Min. clearance at ⌀25 mm (− = interference)
- −28 µm−0.00110 in−0.00110 in−28 µm
Drawing
H7/n6 specifications
| Fit type | Transition |
|---|---|
| Hole limits at ⌀25 mm (µm) | +21 / 0 |
| Shaft limits at ⌀25 mm (µm) | +28 / +15 |
| Max. clearance at ⌀25 mm | 6 µm0.00024 in |
| Min. clearance at ⌀25 mm (− = interference) | −28 µm−0.00110 in |
H7/n6 limits for every size range (µm)
| Size (mm) | Hole ES / EI | Shaft es / ei | Max. clearance | Min. clearance | Type |
|---|---|---|---|---|---|
| ≤ 3 | +10 / 0 | +10 / +4 | +6 | −10 | transition |
| 3–6 | +12 / 0 | +16 / +8 | +4 | −16 | transition |
| 6–10 | +15 / 0 | +19 / +10 | +5 | −19 | transition |
| 10–18 | +18 / 0 | +23 / +12 | +6 | −23 | transition |
| 18–30 | +21 / 0 | +28 / +15 | +6 | −28 | transition |
| 30–50 | +25 / 0 | +33 / +17 | +8 | −33 | transition |
| 50–80 | +30 / 0 | +39 / +20 | +10 | −39 | transition |
| 80–120 | +35 / 0 | +45 / +23 | +12 | −45 | transition |
| 120–180 | +40 / 0 | +52 / +27 | +13 | −52 | transition |
| 180–250 | +46 / 0 | +60 / +31 | +15 | −60 | transition |
| 250–315 | +52 / 0 | +66 / +34 | +18 | −66 | transition |
| 315–400 | +57 / 0 | +73 / +37 | +20 | −73 | transition |
| 400–500 | +63 / 0 | +80 / +40 | +23 | −80 | transition |
Transition fit with likely interference: bronze bushes in housings, gear hubs, parts pressed on with moderate force.
Other fits of the same type (Transition)
All ISO fits
Sources
- ISO 286-1:2010, Geometrical product specifications (GPS): ISO code system for tolerances on linear sizes, Part 1: Basis of tolerances, deviations and fits
- ISO 286-2:2010, Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
- ANSI B4.2-1978 (R2020): Preferred metric limits and fits
Values last checked against these sources on November 15, 2026. · How we check data
Reference values for planning and identification. Confirm critical dimensions with the manufacturer's drawing or the current edition of the standard before production.